Service bulletins for the 2010 Audi S5
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
637 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| A911392 2030947- | 2017-12-05. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 91 number 12-61 dated September 25, 2012. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype®, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone gets the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call assuming the phone is not responding. |
|---|---|
| A911388 2021780- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. Supersedes Technical Service Bulletin Group 91 number 10-70 dated October 26, 2010. Sequence of error messages are seen on the radio display screen after a CD was loaded into or removed from the internal CD drive. "Drive defective. The error could be corrected by resetting it (see radio system owner's manual). Otherwise, contact your Audi dealer." "The CD-drive is damaged and was therefore deactivated." The CD drive cannot be selected in the Source list and is described as "damaged." After the ignition is cycled or a radio reset performed, the CD drive is fully operational. DTC 00468 (CD-ROM Drive -R92- Faulty) is stored in the radio (address word 56). The DTC will be sporadic if the ignition has been cycled or a radio reset performed and will automatically be cleared after 40 ignition cycles without a reoccurrence. Only vehicles with the CAN-based generation 3 radio (Concert (PR 8UQ) or Symphony (PR 8YN)) are affected. |
| A551332 2023967- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM:WIRING:FRONT UNDERHOOD; LATCHES/LOCKS/LINKAGES:HOOD:LATCH. Supersedes Technical Service Bulletin Group 55 number 13-30 dated May 28, 2013. "Low Oil Level" message is on in the DIS or MMI. The hood must be open for at least 30 seconds for a reset of this message to be performed. The message is not reset in the DIS/MMI because the hood has not been recognized as being opened due to an inoperative hood contact switch. |
| A481346 2021191- | 2017-12-05. Service bulletin. STEERING. Supersedes Technical Service Bulletin Group 40 number 09-06 dated August 3, 2009. Customer hears squeaking noises when turning or maneuvering the steering wheel. The folds of the outer CV joint rubber boots can touch each other when the steering wheel is turned. |
| A481345 2034351- | 2017-12-05. Service bulletin. STEERING. Customer may report hearing creaking or squeaking noise from the steering column when steering slowly (the noise can be duplicated while the vehicle is stationary if the steering wheel is turned slowly). The noise may get louder at higher temperatures or when the vehicle is driven for a longer period of time. The noise comes from the sealing sleeve/steering column opening on the bulkhead. Listen to the attached audio file for example of the noise. Insufficient lubrication of the intermediate steering shaft in the area of the sealing sleeve. |
| A461347 2034387- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM; PARKING BRAKE. Customer may report sporadically hearing the parking brake being actuated after the vehicle has been switched off. If the customer does not identify the sound as the sound of the parking brake being actuated, he or she may simply complain of hearing noises from the rear brakes. Ignition is switched off. Steering is locked. Park is selected. Parking brake is not engaged. If the electro-mechanical parking brake is not operated for some time, the free play between brake pads and brake discs increases because of normal brake pad wear. The parking brake control unit performs an automatic correction about every 621 miles (1,000 km). On A8 models, the brake pad thickness is also calculated. |
| A441338 2034445- | 2017-12-05. Service bulletin. TIRES:PRESSURE MONITORING AND REGULATING SYSTEMS. Customer reports seeing the messages "TPMS" and "Tire pressure: System malfunction!" in the instrument cluster. The "TPMS" message is not related to a loss of tire pressure. The message only indicates that tire pressure monitoring system (TPMS) is not active. |
| A371309 2028715- | 2017-12-05. Service bulletin. POWER TRAIN. Supersedes Technical Service Bulletin Group 37 number 12-40 dated February 28, 2012. Rough gear changes, both when accelerating and when slowing down. There is a rough driving power disruption that occurs sporadically and lasts for less than a second. After a mechatronics, torque converter, or complete gearbox replacement, the clutches must be adapted to the new component. This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted. |
| A351313 2030477- | 2017-12-05. Service bulletin. POWER TRAIN. Supersedes Technical Service Bulletin Group 35 number 13-10 dated May 7, 2013. The following message appears in the information display: "Gearbox malfunction: you can continue driving". Fault entries are stored in the transmission control module. Fault codes and expanded environmental conditions codes must match exactly or this TSB should not be followed. Poor internal contact area on circuit board will lead to faults. Oil additives can cause the plastic circuit plates to delaminate, causing contact loss. |
| A191343 2034439- | 2017-12-05. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM:RADIATOR ASSEMBLY; ENGINE AND ENGINE COOLING. The coolant warning light is illuminated. Coolant is leaking from the front intercooler radiator because of stone damage to the radiator. When vehicles are driven on gravel roads, there is a greater chance of front-end stone impact damage to the intercooler radiator. |
| A911374 2024323- | 2017-11-17. Service bulletin. BACK OVER PREVENTION: CAMERA SYSTEM. Supersedes Technical Service Bulletin Group 91 number 12-61 dated October 1, 2012. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions. |
| A551327 2023967- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 55 number 12-24 dated August 7, 2012. "Low Oil Level" message is on in the DIS or MMI. The hood must be open for at least 30 seconds for a reset of this message to be performed. The message is not reset in the DIS/MMI because the hood has not been recognized as being opened due to an inoperative hood contact switch. |
| A441336 2022563- | 2017-11-17. Service bulletin. SUSPENSION. Supersedes Technical Service Bulletin Group 44 number 13-35 dated January 18, 2013. Customer feels vibration from 55 - 80 mph (88 - 128 km/h) in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not result in any handling concerns or loss of vehicle control. |
| A011369 2028344- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM; ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 01 number 12-57 dated October 29, 2012. Noises/inconsistent engine operation after cold start during the catalyst heating phase. The customer may interpret this engine roughness as misfiring. To comply with the legal requirements on exhaust gas emissions according to the LEV-1 and LEV-2 standards, a high exhaust gas quality must be ensured. The necessary catalyst only operates at a temperature over 300°C (572°F). To achieve this, the catalyst is heated up. The catalyst heating phase is achieved by a late ignition angles and by introducing additional fresh air to the exhaust valves (secondary air system). Late ignition angles make sure that the exhaust gas from the cylinders has a higher temperature. This exhaust gas includes fuel that is un-burnt, and was deliberately injected into great quantities. The secondary air system adds fresh air to the exhaust gas as it leaves the cylinder and the extra fuel is burnt. As a result, the temperatures of the exhaust gas and of the catalyst increase quickly. The afterburning in the exhaust manifold before the catalyst changes the sound characteristic of the engine. This heating-up of the catalyst, including afterburning, is normal and has no effect on the service life of the engine. During this catalyst heating phase, the engine has increased idle speed, may have increased vibrations, and has a different sound characteristic. Depending on conditions, the time of the catalyst heating phase varies. |
| A281321 2017555- | 2017-11-17. Service bulletin. EQUIPMENT:ELECTRICAL. Supersedes Technical Service Bulletin Group 28 number 12-19 dated May 1, 2012. The master key with remote control does not engage or stay in the ignition lock. On vehicles without Advanced Key, the remote keys are inoperable. Keyless unlocking/locking using the door handle and keyless opening of the trunk lid using the trunk handle are inoperable. The vehicle cannot be started with the Start/Stop button. The remote keys are inoperable. The message "ignition lock faulty" may appear in the instrument cluster driver information display. DTC 00166 (Access/Start Authorization Switch -E415- Incorrect Signal) may be stored in Comfort System Central Control Module J393 (address word 46). It is possible that objects have been inserted into the ignition lock, which causes the slide of the ignition lock to become stuck in the rear part of the lock (S-contact position). The stuck slide is not allowed to return to the starting point (0-position). |
| A001348 2002047- | 2017-11-17. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Supersedes Technical Service Bulletin Group 00 number 11-19 dated April 8, 2011. This TSB contains information on technician preparation when calling the Audi Technical Assistance Center |
| A191335 2025303- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 11-19 dated February 10, 2011. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service. |
| A421317 2026049- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 42 number 12-14 dated October 5, 2012. Oil leak in the area of the Quattro sports rear differential (PR-PDU, PDR, or GH2) side flange or axle shaft inboard flange. Insufficient sealant on the protective cap on the inboard constant velocity joint at the rear differential on vehicles with a sports differential. |
| A461330 2027636- | 2017-11-17. Service bulletin. SERVICE BRAKES. Supersedes Technical Service Bulletin Group 46 number 12-22 dated June 5, 2012. Brakes squeak or squeal when braking with light to moderate force on vehicles produced before June 20, 2011 (calendar week 25 of 2011). |
| A941312 2017566- | 2017-11-17. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS:SWITCH; EXTERIOR LIGHTING:HEADLIGHTS. Supersedes Technical Service Bulletin Group 94 number 09-23 dated August 12, 2009. Headlight switch knob is pressed in. The switch functions correctly. The headlight switch knob was designed with a normal position and a pushed-in position. This is a deliberate design feature designed to avoid injuries in the event of a collision. |
| A971335 2033412- | 2017-11-17. Service bulletin. STEERING:ELECTRIC POWER ASSIST SYSTEM; STEERING. Steering wheel lock does not work. Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. The ignition key cannot be removed. DTC with description "Brake control unit, no signal/communication" is present in several control units. DTC entry in ABS Control unit, J104 (03). One or more may be present. This condition does not result in any drivability concerns. The steering system is fully connected. This condition does not result in any drivability concerns. The steering system is fully connected. The insulation for the ABS wheel speed sensor is damaged in production. Over time, this can lead to corrosion on the wires and restricted functions with the ABS control module. Only the wires in the left bulkhead grommet are affected. |
| Email Mandatory | 2017-11-17. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This document contains the important email to all Audi dealership personnel in regards to the immediate madatory stop-sale order that is in effect to all vehicles from 20110-2015 that have a 2.0L TDI engine. |
| A961501 2019260- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 96 number 13-67 dated July 10, 2013. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer?s door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 model years 2005?2006 and A3 model year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer?s HomeLink® opener system is using an alternate code. The handheld transmitter?s programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal. |
| A461522 2027636- | 2017-11-17. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Supersedes Technical Service Bulletin Group 46 number 15-21 dated September 11, 2015. Customer may complain about brake squeak or squeal with light to moderate pedal pressure. |
| A461521 2027636- | 2017-11-17. Service bulletin. SERVICE BRAKES. Supersedes Technical Service Bulletin Group 46 number 15-17 dated July 14, 2015. Customer may complain about brake squeak or squeal with light to moderate pedal pressure. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.