WenmarOpen by Wenmar Pro

Service bulletins for the 2012 Audi S4

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

795 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
A171561 2030197-2017-10-21. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 17 number 15-59 dated March 17, 2015. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner's Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue, and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions.
A011519 2040403-2017-10-21. Service bulletin. ELECTRICAL SYSTEM:STARTER ASSEMBLY:SOLENOID; ENGINE AND ENGINE COOLING. The MIL is on. DTCs P2440(00) and/or P2442(00) are stored in the ECM. One of the combi valves is defective or the vacuum solenoid is defective.
A911579 2038824-2017-10-21. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 91 number 14-69 dated November 4, 2014. The following message appears on the MMI display: "Device or cable type not supported". The AMI cable being used is a genuine Audi-branded cable with an Audi part number (see Required Parts and Tools for a list of valid part numbers). The "Device or cable type not supported" message may be displayed when an incorrect AMI cable type is connected to the MMI system. Only cables with an Audi part number (i.e., 4F0.XXX.XXX) are supported by the MMI system. Volkswagen-branded cables look similar, but are not guaranteed to work with Audi MMI systems. The label on the end of an Audi-branded cable has an Audi logo and Audi part number. Audi-branded cables have unique firmware inside the hardware that can determine which MMI system and iOS device are connected to the cable. Volkswagen cables do not have this firmware. The firmware is required to allow the system to function normally due to the different technology available in the different MMI systems and in the different iPhones and iPod Touch devices. In addition, the AMI system was designed to play the music stored locally on the connected device only. Music streaming (from Spotify or Pandora, for example) is not supported, and music stored in the cloud (on Google Play, Amazon Prime, or iTunes Match/iCloud, for example) may drop out, pause, and skip when played.
A911578 2011500-2017-10-21. Service bulletin. EQUIPMENT:ELECTRICAL; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. Supersedes Technical Service Bulletin Group 91 number 08-129 dated November 12, 2008. Customer states that the reception of satellite radio occasionally fades or drops out. The information display may show a message related to the satellite radio, such as "Linking", "Updating", "Acquiring Signal", "Loading", "No Signal", or "No Sat".
A171557 2010043-2017-10-21. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 17 number 13-35 dated January 9, 2013. This bulletin lists engine oils that meet Audi oil quality standards (VW 501 01, 502 00, 505 00, 505 01, and 504 00/507 00).
A101511 2018288-2017-10-21. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 10 number 13-10 dated September 5, 2013. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these metal debris pieces are not removed prior to the installation and operation of the replacement engine, they could be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage.
A011514 2014753-2017-10-21. Service bulletin. FUEL SYSTEM, GASOLINE. Supersedes Technical Service Bulletin Group 01 number 13-09 dated June 21, 2013. The use of contaminated gasoline or gasoline with a low content of deposit control additives may result in excessive accumulation of deposits on intake valves, intake manifold, fuel injectors, and combustion chambers, engine running rough after cold start, excessive engine cranking time, hesitations while driving, rough engine idle, Reduced engine performance, and/or Poor fuel economy. Conditions may be severe enough to illuminate the MIL in conjunction with storage of DTCs for misfire, lean fuel system, or air/fuel ratio imbalance in the engine control module. Condition may be caused by use of contaminated gasoline. Condition may be caused by use of gasoline with a low content of deposit control additives.
Customer Letter2017-10-21. Service bulletin. FUEL SYSTEM, OTHER:FUEL INJECTION SYSTEM. This document contains information on the warranty extension for fuel injectors.
Customer Letter2017-10-21. Service bulletin. FUEL SYSTEM, OTHER:FUEL INJECTION SYSTEM. This document contains information on the warranty extension for fuel injectors.
A191777 2046712-2017-10-04. Service bulletin. ENGINE AND ENGINE COOLING. This informational bulletin contains guidelines for figuring out why coolant marks are present around the coolant expansion tank cap.
A011703 2033001-2017-10-04. Service bulletin. ENGINE. This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A011701 2033001-2017-10-04. Service bulletin. ENGINE. This bulletin provides instructions on how to clean the secondary air ports if they have too much carbon and cause a restriction.
A351620 2030477-2017-10-04. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. Gearbox malfunction message in cluster. DTCs P17D800, P179D00, P174000, P174C, P174B, P174F, P179C, P174A, and/or P174E are stored in the transmission control module. Fault codes and symptom codes must match exactly or this TSB should not be followed. Poor internal contact area on circuit board will lead to faults. Oil additives can cause the plastic circuit plates to delaminate, causing contact loss.
Elsa Newsletter2017-10-04. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. TSBs in this newsletters include the MIL on due to DTC P042000 and/or P043000 (Catalyst system Bank 1/2, Efficiency below threshold) being stored in the ECM. New ECM software implemented to correct the condition.
A351619 2032211-2017-10-04. Service bulletin. STEERING:GEAR BOX (OTHER THAN RACK AND PINION); POWER TRAIN:AUTOMATIC TRANSMISSION; ELECTRICAL SYSTEM. Gearbox warning light on (DTCs P179E00, P179F00, P0700, P060A). The driver information system displays the message "gearbox malfunction: you can continue driving". There are two scenarios present. Scenario 1 is that entries are logged individually or in combination, with P179E logged first (using DTC environmental data).The entries are DTC P179E (Drive position sensor electrical error), DTC P0700 with DFCC 20196 (Transmission control system malfunction), DTC P1758 with DFCC 8464 (Terminal 15 voltage supply open circuit), and DTC P060A with DFCC 8126, 8345 (Internal control module monitoring processor performance) In this scenario, if DTC P179E is not logged first, this TSB does not apply. Scenario 2 is that entries are logged individually or in combination. The order in which the DTCs are logged is not relevant. The entries are DTC P179E with DFCC 8050, 8051, 8052, 8053, 17595, 17596, 17597, 17598, 17602 (Drive position sensor electrical error), DTC P179F with DFCC 8054, 8055, 8056, 8057, 17599, 17600, 17601 (Drive position sensor malfunction), DTC P0716 with DFCC 8096, 8101, 18153, 20738 (Input turbine/speed sensor ?A? circ. range/performance), DTC P171F with DFCC 8097, 8102, 18154 (Transmission input speed (RPM) sensor 2 implausible signal), DTC P0715 with DFCC 8094, 8103, 18161 (Input turbine/speed sensor ?A? circuit.), DTC P2765 with DFCC 8095, 8104 (Input turbine/speed sensor ?B? circuit), DTC P0501 with DFCC 8098 (Vehicle speed sensor ?A? range/performance), and DTC P2159 with DFCC 8099 (Vehicle speed sensor ?B? range/performance). Fault codes and DFCC codes must match exactly for this TSB to apply. The DFCC is the 4-6 digit code that is typically listed before the fault code. Incorrect driving mode sensor module.
A191666 2043142-2017-10-04. Service bulletin. ENGINE; ENGINE AND ENGINE COOLING:COOLING SYSTEM; ENGINE AND ENGINE COOLING. The MIL is sporadically on. One or more of the following DTCs is stored in the engine control module (ECM, J623 (address word 01). They are DTC P261A00 (Coolant Pump ?B? Control Circuit/Open), DTC P261B00 (Coolant Pump ?B? Control Circuit Range/Performance), and DTC P261C00 (Coolant Pump ?B? Control Circuit Low). The continued coolant circulation pump sporadically fails.
A011650 2026299-2017-10-04. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. MIL is on due to One of the following DTCs for air-fuel ratio imbalance is stored in the engine control module (ECM), J623 (address word 01): DTC P219C00 (stored in cylinder 1), DTC P219D00 (stored in cylinder 2), DTC P219E00 (stored in cylinder 3), DTC P219F00 (stored in cylinder 4), DTC P21A000 (stored in cylinder 5), DTC P21A100 (stored in cylinder 6). An incorrect software setting causes the DTC to be stored. TSB 2011732 00 Software Version Management (SVM), operating instructions will be necessary to complete this procedure.
A011649 2041120-2017-10-04. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. The MIL is on due to DTC P042000 and/or P043000 (Catalyst system Bank 1/2, Efficiency below threshold) being stored in the engine control module (ECM), J623 (address word 01). The diagnostic limitations were too narrow. New ECM software implemented to correct the condition.
A921614 2038151-2017-09-27. Service bulletin. VISIBILITY:WINDSHIELD WIPER/WASHER. This bulletin provides instructions for repairing a vehicle with a washer solvent light on but the level is correct.
A201676204375842017-03-17. Service bulletin. FUEL SYSTEM, OTHER:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS. THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO DIAGNOSE ISSUES WITH FUEL PRESSURE AND TO REPLACE THE FUEL DELIVERY UNIT IF DEVIATIONS ARE FOUND.
A201675204375832017-03-17. Service bulletin. FUEL SYSTEM, OTHER:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS. THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO DIAGNOSE ISSUES WITH FUEL PRESSURE AND TO REPLACE THE FUEL DELIVERY UNIT IF DEVIATIONS ARE FOUND.
A011673 2040403-2017-03-17. Service bulletin. ENGINE AND ENGINE COOLING. THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO REPLACE EITHER A COMBI VALVE OR VACUUM SOLENOID VALVE DEPENDING ON THE CIRCUMSTANCES UNDER WHICH DTC P244000 AND/OR P244200 WERE STORED.
2012-3-17-20162017-03-16. Service bulletin. VISIBILITY/WIPER; VISIBILITY:WINDSHIELD WIPER/WASHER. "MODIFIED WIPER BLADE CHECK FOR US: WIPER BLADES – CHECK CONDITION AND REPLACE IF NECESSARY (USA ONLY) ADDED WIPER BLADE CHECK FOR CAN: WIPER BLADES – CHECK CONDITION (CANADA ONLY)"
A1716732030197162017-03-14. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. THIS TECHNICAL SERVICE BULLETIN INSTRUCTS THE READER TO TEST FOR EXCESSIVE OIL CONSUMPTION AND UPDATE THE SOFTWARE IF NEEDED.
A011665203545442017-03-14. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. THIS TECHNICAL SERVICE BULLETIN CONTAINS INSTRUCTIONS FOR PRESSURE WASHING PORTS TO RESOLVE AN "AIR SYSTEM -- ACTION REQUIRED" MESSAGE.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.