Service bulletins for the 2014 Audi Q7
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1122 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Electrical system are shown. Show all
| A371451 2036113- | 2017-12-05. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 37 number 13-19 dated December 20, 2013. The ignition key cannot be removed even though the gear shifter is in Park (P). The vehicle is mechanically in the Park position, but this is not recognized electronically. The gear shifter cannot be moved from the Park position. On vehicles with advanced key, the vehicle cannot be locked by remote control after the engine has been switched off. DTC 00230: Transmission park selector switch-F305 - short circuit to ground may be sporadically stored in the vehicle authorization system control module. The Park position of the gear shifter is sporadically not recognized, which causes the ignition key to not be cleared and prevents the vehicle from being locked. |
|---|---|
| A971337 2034945- | 2017-12-05. Service bulletin. EXTERIOR LIGHTING:HAZARD FLASHING WARNING LIGHTS; ELECTRICAL SYSTEM. The customer may report two or more warning lights are/were illuminated simultaneously. The warning lights may be sporadic, and may not be illuminated by the time the customer brings the vehicle to the workshop. CAN communication DTCs may be found in control modules. There is sporadic data disruption on the CAN bus wiring behind the dashboard, between the left (T46a) and right (T46b) 46-pin CAN disconnect plugs. |
| A941323 2033675- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM:WIRING: REAR COMPARTMENT/TRUNK; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 94 number 13-17 dated May 22, 2013. DTC 03073 (Closed Rear Lid Sensor - Incorrect Signal) may be stored in the comfort system central control module, J393 (address word 46). In order for the vehicle to receive a proper rear lid status signal when the lid is operated, the paddle switches on the rear sill trim must contact the opposing lid latch points uniformly. When the rear lid is opened, the paddle switches change state and the comfort system central control module 2, J773, will read G525 and G526. It will then communicate to the comfort system central control module, J393. |
| A911392 2030947- | 2017-12-05. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 91 number 12-61 dated September 25, 2012. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype®, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone gets the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call assuming the phone is not responding. |
| A551331 2033675- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM:WIRING: REAR COMPARTMENT/TRUNK. DTC 03073 (Closed Rear Lid Sensor - Incorrect Signal) may be stored in the comfort system central control module, J393 (address word 46). In order for the vehicle to receive a proper rear lid status signal when the lid is operated, the paddle switches on the rear sill trim must contact the opposing lid latch points uniformly. When the rear lid is opened, the paddle switches change state and the comfort system central control module 2, J773, will read G525 and G526. It will then communicate to the comfort system central control module, J393. |
| A461347 2034387- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM; PARKING BRAKE. Customer may report sporadically hearing the parking brake being actuated after the vehicle has been switched off. If the customer does not identify the sound as the sound of the parking brake being actuated, he or she may simply complain of hearing noises from the rear brakes. Ignition is switched off. Steering is locked. Park is selected. Parking brake is not engaged. If the electro-mechanical parking brake is not operated for some time, the free play between brake pads and brake discs increases because of normal brake pad wear. The parking brake control unit performs an automatic correction about every 621 miles (1,000 km). On A8 models, the brake pad thickness is also calculated. |
| A011380 2024344- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 01 number 11-19 dated February 3, 2011. MIL on. Vehicle has reduced performance (in "limp mode"). Various entries may be logged. After recognizing that the boost pressure is too low or too high, the engine control module switches to emergency operation and the engine performance is reduced via the injected fuel quantity ("limp mode"). |
| A571385 2017082- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM; LATCHES/LOCKS/LINKAGES:DOORS:LATCH. Supersedes Technical Service Bulletin Group 57 number 13-82 dated February 5, 2013. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders. |
| A941310 2029194- | 2017-11-17. Service bulletin. EXTERIOR LIGHTING; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 94 number 13-03 dated February 1, 2013. Only vehicles with Xenon headlights can be affected by this condition. The customer complains the high beams do not function on one side or one of the low beams flickers intermittently. In addition to this, an "Adaptive Headlight Defective" warning can be present in the cluster if the vehicle has the Prestige trim level. One of the following DTCs are set in the vehicle electrical system control module, J519 (09), or in the headlamp range control module, J431 (55), depending on the trim level of the vehicle. Vehicles with the Premium Plus option package can have the DTC set in the J519 (09) module. Vehicles with the Prestige option package can have the DTC set in the J431 (55) module. One or more of the connectors inside the headlamp housing are disconnected fully or partially from the factory. |
| A961501 2019260- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 96 number 13-67 dated July 10, 2013. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer?s door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 model years 2005?2006 and A3 model year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer?s HomeLink® opener system is using an alternate code. The handheld transmitter?s programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal. |
| A911517 2042013- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. While using Audi connect, the customer cannot access the online destination search and/or the Google Earth navigation view. ?This service is currently unavailable. Please try again later" message appears in the MMI. The customer may also see an error message in the myAudi portal indicating that one or multiple licenses are expired and must be renewed. Replacing the SIM card or MMI hardware or performing the SVM recovery activation will not remedy the concern. |
| A481567 2017266- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 48 number 14-62 dated September 23, 2014. Electrically-adjustable steering column adjustment is restricted and does not adjust vertically. Incorrect operation of Easy Entry is not the cause. It is unlikely that external forces have led to the loss of the stored end positions of the adjustment movement. See TSB 2015819, 48 Easy Entry function of the power adjustable steering column intermittently does not work, for more information. Seat adjustments can be used to maintain the 10-inch minimum recommended distance from the steering wheel in case of airbag deployment. The axial adjustment is still functional during this condition. The steering column may be under tension due to unfavorable tolerances of the steering column and module cross carrier. As a result, the current draw of the regulator motors is above specification, which causes the electric steering column adjustment to fail. Once the vehicle electrical system control module, J519 (address word 09), detects an excessive current draw, the basic settings will be erased. If basic settings are not stored in the vehicle electrical system control module, the module will not send voltage/current to the motor to operate the vertical adjustment. |
| A011542 2041787- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM. DTCs are stored in the ECM. There may be soot buildup on the moveable elements of the pressure sensing glow plug (PSG). |
| A911529 2013422- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 91 number 13-04 dated September 11, 2013. The Bluetooth® telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present. |
| A171568 2028440- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY. Supersedes Technical Service Bulletin Group 17 number 14-49 dated April 3, 2014. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer. |
| A011309 2014753- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE. Supersedes Technical Service Bulletin Group 00 number 10-01 dated February 5, 2010. Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Excessive engine cranking time. Hesitations while driving. Rough engine idle. Reduced engine performance. Poor fuel economy. Conditions may be severe enough to illuminate the MIL in conjunction with storage of DTCs for misfire (example: P0300, P030x) and / or lean fuel system (example: P0171, P0174, P1128, P1130, P1136, P1138) in the engine control module (ECM). Condition may be caused by use of contaminated gasoline. Condition may be caused by use of gasoline with a low content of deposit control additives. |
| A941298 2028277- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING:HEADLIGHTS; EQUIPMENT. Supersedes Technical Service Bulletin Group 94 number 12-91 dated October 24, 2012. Considerable moisture present in headlamp. The moisture disappears only after extended drives (greater than 10 minutes). No external damage to headlamp which could introduce moisture. Humid air settles on the inside of the glass, causing moisture to appear on the inside of the headlamp lens. Because of the headlamp circulation system, outside air is allowed to flow through the headlamps. The open, water-protected ventilation system (needed for pressure compensation) creates different ? climate zones? inside the headlamp, where the lens is either warmed up by the light or cooled down by passing air. When high air humidity and temperature differences exist between the inside of the headlamps and the outside, condensation can form on the inside of the lens, especially in cold and wet weather. The moisture in the headlamps can be compared with condensation on the windshield, which is cleared by the "defroster vent". This moisture buildup can happen for example: after a car wash, after steam cleaning of the engine or the front end, or after overnight temperature changes. This condition is more easily visible with headlamps made from clear glass. The moisture is an optical condition which does not affect the headlamp function (light performance) and does not lead to corrosion nor does it lead to damage of the internal headlamp parts. This condition is common to all exterior vehicle lights, and can occur on every headlamp, fog lamp, or rear lamp. |
| A941299 2029194- | 2017-11-08. Service bulletin. EXTERIOR LIGHTING; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 94 number 12-74 dated April 23, 2012 . The customer complains the high beams do not function on one side or one of the low beams flickers intermittently. In addition to this, an ? Adaptive Headlight Defective? warning can be present in the cluster if the vehicle has the Prestige trim level. DTCs are set in the 09 ? Central Electric Control Unit or in the 55 ? Headlamp Range Control Unit depending on the trim level of the vehicle. Vehicles with the Premium Plus option package can have the DTC set in the 09 module. Vehicles with the Prestige option package can have the DTC set in the 55 module. One or more of the connectors inside the headlamp housing are disconnected fully or partially from the factory. |
| A571278 2031413- | 2017-11-08. Service bulletin. SEATS; ELECTRICAL SYSTEM. The seat memory does not work. The MMI displays that the memory function is not active. The seat memory control unit can be deactivated due to voltage fluctuations in the vehicle? s power system, or from a large static discharge through the seat cover. If the seat memory control unit is deactivated due to the above mentioned influences, the control unit cannot be reactivated through any vehicle controls, vehicle keys, or through the normal GFF test plans. It can only be reactivated with special test plans within the tester. |
| A571279 2018737- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Supersedes Technical Service Bulletin Group 57 number 10-32 dated September 9, 2010. Customer may complain that the vehicle locks itself when removing the key from the ignition lock. When removing the ignition key from the ignition, the customer may unintentionally operate the lock button of the remote key. With the S contact in the ignition lock off (key is removed), the central locking will resume to respond to signals from the remote key. MVB 17 in electric control unit address $46 (Comfort System Central Control Module) can be used for argumentation. The last received central locking command is stored in this MVB. A value of ?2? indicates a locking command last sent from the remote key. With the Autolock feature, MVB 17 is overwritten. Therefore MVB 17 must be read immediately after the complaint. |
| A901238 2032113- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. The customer may state that the outside ambient temperature display is incorrect. To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor measurement. The display will not change faster than 4° F (2° C) per minute. This concept applies to both falling and rising temperatures. A programming strategy is also implemented to avoid incorrect readings on a parked vehicle, due to the temperature sensor being affected by outside influences such as radiant heat from the engine bay, elevated road surface temperatures, etc. |
| A571402 2022032- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 57 number 13-97 dated October 29, 2013. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. The lock command history is stored in the convenience system control module (J393). |
| A011485 2036761- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 01 number 14-71 dated March 13, 2014. The MIL is on. DTC P164B(00) is stored in the engine control module.The oil pressure switch is defective. |
| A001466 2037949- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated. This DTC is normal. It indicates that the parameter data has not been properly programmed into the ECU by SVM. |
| A001465 2011732- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 00 number 12-32 dated February 7, 2012. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.