Service bulletins for the 2012 Audi Q7
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1131 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Engine are shown. Show all
| A011313 2034359- | 2017-12-05. Service bulletin. ENGINE. MIL on. DTC P20E9 is stored in the engine control module (ECM). In vehicles produced during a certain period, the AdBlue filter seal within the level sensor module may have been damaged during the assembly process. This damaged seal can allow unfiltered AdBlue to be sucked into the delivery system, subsequently damaging the pressure sensor and reducing agent pump V437. |
|---|---|
| Dealer Letter - | 2017-11-17. Service bulletin. FUEL SYSTEM, OTHER; ENGINE. Due to Illinois state tax incentives for biofuels, biodiesel blends of B5 or less may not be available in the State of Illinois. Because Audi supports the development and use of renewable fuels (such as biodiesel fuel blends), customers with 2009-2013 MY Audi TDI® Clean Diesel Engine vehicles registered in the State of Illinois only will receive a communication on or about February 21, 2013 regarding the use of biodiesel fuel blends in their vehicles. Audi will continue to honor the terms and conditions of Audi Limited Warranties that came with these vehicles. Please refer to Warranty Policies & Procedures Bulletin AWA 13-01 for additional information. |
| A171336 2030197- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 17 number 12-34 dated December 12, 2012. Customer complains of excessive oil consumption. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner's Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods. |
| A011380 2024344- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 01 number 11-19 dated February 3, 2011. MIL on. Vehicle has reduced performance (in "limp mode"). Various entries may be logged. After recognizing that the boost pressure is too low or too high, the engine control module switches to emergency operation and the engine performance is reduced via the injected fuel quantity ("limp mode"). |
| A011383 2033001- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING; ENGINE AND ENGINE COOLING:COOLING SYSTEM. MIL on. DTC P0491 and P0492 (Secondary Air System Insufficient Flow, Bank 1/2) are stored at the same time. Mileage is greater than 15,000 miles. Under certain driving conditions, the secondary air ports in the cylinder head can accumulate carbon over time, causing a restriction. |
| A171337 2030197- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 17 number 13-36 dated February 14, 2013. Customer complains of excessive oil consumption. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner's Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods. |
| A171338 2012913- | 2017-11-17. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 17 number 10-07 dated June 3, 2010. Oil filter cartridge requires replacement. |
| A171339 2030197- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 17 number 13-37 dated March 13, 2013. Customer complains of excessive oil consumption. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions, internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This can occur while the vehicle is operated in city driving conditions, for example: stop and go traffic with extended idle periods. |
| A191335 2025303- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 11-19 dated February 10, 2011. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service. |
| A191562 2025303- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 15-61 dated July 7, 2015. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service. |
| A171565 2038129- | 2017-11-17. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 17 number 15-63 dated June 2, 2015. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual. |
| Dealer Letter - | 2017-11-17. Service bulletin. ENGINE. This is an update to the November 12, 2015, communication regarding the stop sale order for all 2013-2016 model year Audi vehicles equipped with a 3.0 liter V6 TDI engine. Audi is adding 2009-2012 model year Audi Q7 vehicles equipped with a 3.0 liter V6 TDI engine in CPO inventory to Stop Sale Code STP5. The STP5 code will be visible in Elsa for these vehicles on November 23, 2015. |
| A191341 2025303- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 13-35 dated March 25, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service. |
| A171233 2030197- | 2017-11-08. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 10 number 12-09 dated October 1, 2012. Engine oil consumption too high. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner? s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This condition can occur while the vehicle is operated in metro driving conditions, for example: Stop and go traffic with extended idle periods. |
| A871236 2012886- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING; VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM. Supersedes Technical Service Bulletin Group 87 number 10-07 dated September 2, 2010. The A/C system is not cooling as desired in hot weather areas. The following are suggestions to achieve maximum cooling efficiency in hot weather areas. |
| A101209 2030197- | 2017-11-08. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 10 number 12 ? 08 dated September 5, 2012. Engine oil consumption too high. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This condition can occur while the vehicle is operated in metro driving conditions, for example: Stop and go traffic with extended idle periods. |
| A011263 2031458- | 2017-11-08. Service bulletin. ENGINE; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 01 number 12-58 dated November 5, 2012. MIL on, with DTCs stored in the 01 (Engine Control Module). Under extreme driving conditions, such as a driving profile of mainly short distance (stop and go) driving high crankcase pressure can lead to the above described DTC codes. By changing the crankcase pressure valve to a lower operating pressure this condition can be improved and eliminate the mentioned possible DTC codes. Along with the crankcase pressure being lowered, a new ECM software level is required to compensate for new crankcase pressure. |
| A171234 2030197- | 2017-11-08. Service bulletin. EQUIPMENT; ENGINE. Supersedes Technical Service Bulletin Group 17 number 12-33 dated November 21, 2012. Engine oil consumption too high. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner? s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature, and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Under certain driving conditions internal engine pressure conditions in the 3.0 TFSI engine can negatively influence the rate of oil consumption. This condition can occur while the vehicle is operated in metro driving conditions, for example: Stop and go traffic with extended idle periods. |
| A001463 2033576- | 2017-11-08. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Supersedes Technical Service Bulletin Group 00 number 13-49 dated May 14, 2013. Although the correct amount of oil was added to the engine during an oil change service, a check of the oil level shows that the oil level is not okay. When an unapproved aftermarket speed-filling device is used to add oil to the engine, the increased oil flow rate may force oil into the intake manifold or combustion chamber, creating the potential for engine damage. |
| A191450 2025303- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 13-41 dated June 20, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service. |
| A971441 2036764- | 2017-11-08. Service bulletin. ENGINE; ELECTRICAL SYSTEM. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly. |
| A801406 2033806- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM. Supersedes Technical Service Bulletin Group 80 number 13-05 dated September 11, 2013. Malfunction Indicator Lamp is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. "Limp Home" mode is active. Faults are stored in the transmission control module (address word 02). Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss, or due to a faulty N82 control valve. Inspection of the coolant control valves N82, N509, or N488 reveals the presence of coolant inside the electrical connector as shown in the illustration. The connectors, wiring harness, and/or connected control units may have been damaged from exposure to coolant. |
| A191449 2036852- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN. Cooling fans stay on after engine is turned off. The cooling fans may operate for up to 10 minutes after the engine is turned off. This function is mapped to specific driving patterns and vehicle operating modes (for example, DPF regeneration). This is normal operation, and no parts should be replaced. |
| A011473 2031458- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CRANKCASE (PCV); ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 01 number 13-45 dated December 5, 2013. The MIL is on. DTCs are stored in the ECM. Under extreme driving conditions (such as short-distance, stop-and-go driving), high crankcase pressure can cause the DTCs to appear. The condition can be improved and the DTCs eliminated when the crankcase pressure valve is changed to a lower operating pressure and the ECM software is updated to compensate for new crankcase pressure. |
| A011471 2036761- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING. The MIL is on. DTC P164B(00) is stored in the ECM. The oil pressure switch is defective. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.