Service bulletins for the 2014 Audi Q5
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1389 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
| A911430 2017425- | 2017-11-08. Service bulletin. EQUIPMENT:ELECTRICAL. Supersedes Technical Service Bulletin Group 91 number 10-08 dated March 18, 2010. On generation III Concert and Symphony radios , the control knob or volume knob is broken or loose. Knobs may be damaged by outside influence. |
|---|---|
| A461481 2037044- | 2017-11-08. Service bulletin. SERVICE BRAKES. Customer may report that the front brakes squeal during the first stop in the morning when vehicle is back out of the driveway and when brakes are applied after driving direction is changed at slow speeds. This condition may occur more frequently during cold weather conditions (without rain), and the noise will disappear as temperature increases. This PSS TSB does not apply to Q5 2.0T and Hybrid models. Various parts have been replaced under warranty for the condition noted above, but no issues have been identified with the replaced parts. |
| A461480 2037029- | 2017-11-08. Service bulletin. SERVICE BRAKES. Customer may report hearing brake noise when the vehicle comes to a stop. |
| A441449 2022563- | 2017-11-08. Service bulletin. SUSPENSION. Supersedes Technical Service Bulletin Group 44 number 13-44 dated November 21, 2013. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 - 80 mph (88 - 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires or an imbalance of the wheel and tire assembly. Tires with higher mileage and/or wear should be inspected to determine the best correction for the issue (repair or replacement). Tire life and condition should be determined prior to starting any diagnosis or repair for a vibration. |
| A271424 2025360- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. Supersedes Technical Service Bulletin Group 27 number 12-12 dated February 28, 2012. Customer may report that the vehicle does not start due to a discharged battery. The vehicle has either a battery diagnostic management control module or a battery energy management control module. This TSB provides basic diagnosis steps for discharged batteries, general tips for working with batteries, and system verification steps to ensure that the vehicle is configured correctly. |
| A201433 2036866- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING. MIL and/or glow plug light on. DTC P304300 is stored in the engine control module. Some pumps may draw slightly too much current, which causes the fuel pump malfunction DTC to be stored. |
| A171449 2028440- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. Supersedes Technical Service Bulletin Group 17 number 12-26 dated January 20, 2012. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer. |
| A971442 2036764- | 2017-11-08. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 97 number 14-41 dated March 18, 2014. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system, including: P056200, P057100, P068700, P068A00, P162400, P190C00, U010000, U010100, U012100, U014600, U015500, U021200, U101100, U102600, U111100, U111300, U140000, VAG00003, VAG00185, VAG00263, VAG00317, VAG00384, VAG00446, VAG00456, VAG00457, VAG00466, VAG00473, VAG00532, VAG00565, VAG00591, VAG00714, VAG00819, VAG00955, VAG01217, VAG01299, VAG01314, VAG01315, VAG01317, VAG01320, VAG01330, VAG01331, VAG01332, VAG01334, VAG01333, VAG01336, VAG01705, VAG01964, VAG02067, VAG02072, VAG02095, VAG02103, VAG02203, VAG02214, VAG02635, VAG02812, VAG02874, VAG03041, VAG03157, VAG03166, VAG03220, VAG03278, and/or VAG03531. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly. |
| A971441 2036764- | 2017-11-08. Service bulletin. ENGINE; ELECTRICAL SYSTEM. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly. |
| A961482 2036344- | 2017-11-08. Service bulletin. LATCHES/LOCKS/LINKAGES:DOORS:LATCH; EQUIPMENT:ELECTRICAL:ANTI-THEFT DEVICES. The vehicle's anti-theft alarm sounds when the driver door is unlocked with a mechanical key. No DTCs are stored. The keyless remote was not used to unlock the vehicle. In order to minimize current draw after the ignition has been turned off, the electronics system of the vehicle goes into sleep mode. During this time, each module monitors the CAN bus more slowly than when the electronics system is awake. Because the system is being monitored more slowly, there is a delay in the waking of the central locking system. This delay causes a delay in the disabling of the anti-theft alarm system when the manual key is used. If the key is turned in less than a quarter of a second, the system can unlock the vehicle even though the anti-theft alarm has not been disabled. |
| A941434 2036670- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING:HEADLIGHTS. The high beam is inoperative on one side of the vehicle. The low beams operate correctly. A warning may appear in the instrument cluster. DTCs may be present in the central electrics control module, J519 (address word 09). The connection for the high beam shutter is not connected in the affected headlight. |
| A911429 2026888- | 2017-11-08. Service bulletin. EQUIPMENT:ELECTRICAL. Supersedes Technical Service Bulletin Group 91 number 12-50 dated August 1, 2012. Echo effects, caller on either end cannot hear conversation, sound distortion or feedback, and the sound is distorted, hisses, or scrapes occur during a phone call. This bulletin provides guidelines for analyzing the call quality of the Bluetooth system in the vehicle, and is not applicable to any Audi warranty. |
| A911428 2036576- | 2017-11-08. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT:ELECTRICAL. Supersedes Technical Service Bulletin Group 91 number 14-26 dated February 24, 2014. The MMI screen goes blank then restarts or the MMI screen freezes for a few minutes then recovers when a phone is connected to the vehicle via Bluetooth when the user searches for a contact name in the MMI address book (by using the MMI control knob or the voice recognition system). This condition occurs because special characters (including symbols, emoticons, or map icons) are stored in the name field of a phonebook contact. |
| A911427 2036575- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). The addresses and contacts stored in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus disappear intermittently in vehicles with MMI3G+ Navigation, and in vehicles with or without Audi connect. Intermittently, the MMI system does not appear to remember that the user's myAudi PIN has already been entered, and it requires the user to enter the PIN again in vehicles with Audi connect. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is paired to the vehicle, those addresses and contacts will only be visible any time that the same phone is paired to the vehicle. Any time that the same phone is not paired to the vehicle, the addresses and contacts will not be available. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is not paired to the vehicle, the addresses and contacts will be available any time. In vehicles with Audi connect, the user is prompted to enter the myAudi PIN when selecting online destinations or when importing contacts from the myAudi account. If the user?s Bluetooth phone (the same phone that was paired to the vehicle when the PIN was entered initially) is paired to the vehicle, the user will not be prompted to re-enter the PIN after it has been entered. |
| A801406 2033806- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM. Supersedes Technical Service Bulletin Group 80 number 13-05 dated September 11, 2013. Malfunction Indicator Lamp is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. "Limp Home" mode is active. Faults are stored in the transmission control module (address word 02). Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss, or due to a faulty N82 control valve. Inspection of the coolant control valves N82, N509, or N488 reveals the presence of coolant inside the electrical connector as shown in the illustration. The connectors, wiring harness, and/or connected control units may have been damaged from exposure to coolant. |
| A691428 2023323- | 2017-11-08. Service bulletin. AIR BAGS:FRONTAL:SENSOR/CONTROL MODULE-INACTIVE; AIR BAGS. Supersedes Technical Service Bulletin Group 69 number 13-26 dated October 21, 2013. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. An SVM code is required to code and parameterize the new service replacement airbag control module. Each model's SVM code is provided in a parts bulletin (GP bulletin), which should have been referenced through ETKA when the module was replaced. The control module cannot be coded until the SVM code has been executed. If the SVM code was not acquired through the GP bulletin in ETKA, follow the instructions in the Service section of this bulletin to update the control module. |
| A201432 2035073- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING. upersedes Technical Service Bulletin Group 20 number 14-31 dated January 9, 2014. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak. |
| A191449 2036852- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM:FAN. Cooling fans stay on after engine is turned off. The cooling fans may operate for up to 10 minutes after the engine is turned off. This function is mapped to specific driving patterns and vehicle operating modes (for example, DPF regeneration). This is normal operation, and no parts should be replaced. |
| A011475 2036668- | 2017-11-08. Service bulletin. FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP; FUEL SYSTEM, GASOLINE. Supersedes Technical Service Bulletin Group 01 number 14-69 dated March 6, 2014. The MIL is on. No start or rough running. DTCs are stored in the ECM. When diagnosing a MIL on, no-start, or rough running concern on a common rail diesel vehicle, and no root cause is found after checking all other components and following all GFF diagnostic procedures, it may be necessary to check for metallic particles in the High Pressure Fuel Pump. |
| A011471 2036761- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING. The MIL is on. DTC P164B(00) is stored in the ECM. The oil pressure switch is defective. |
| A011469 2036668- | 2017-11-08. Service bulletin. FUEL SYSTEM, GASOLINE:DELIVERY:FUEL PUMP. The MIL is on. No start or rough running. DTCs are stored in the ECM. When diagnosing the condition listed above on a common rail diesel vehicle, if no root cause is found after all GFF diagnostic procedures have been performed, it may be necessary to check for metallic particles in the high pressure fuel pump using the procedure in the Service section of this bulletin. |
| A941432 2017806- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING:BACK UP LIGHTS. Supersedes Technical Service Bulletin Group 94 number 13-19 dated May 23, 2013. The light bulb warning light is displayed in the instrument cluster with the ?Vehicle lights: malfunction? message. DTCs are stored in the vehicle electrical system control module. Exterior lights are functioning properly. If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after approximately ten seconds. Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is turned to a defined position, and the status of DTC 03280 or DTC 01800 are changed to sporadic. After 40 driving cycles without an implausible signal detected, the DTCs are automatically cleared. |
| A911424 2020399- | 2017-11-08. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT ADAPTIVE/MOBILITY. Supersedes Technical Service Bulletin Group 91 number 09-30 dated April 14, 2009. The Audi MMI system will not play audio files from an SD card. The MMI system does not recognize the audio files on the SD card. The MMI system reports that the audio files on the SD card are damaged. The audio files on the SD card will play on one Audi vehicle, but will not play on a different Audi vehicle. |
| A911419 2026895- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 91 number 11-16 dated October 5, 2011. During a Bluetooth call, the sound is difficult to hear for the other party. Voice recognition accuracy is poor. This TSB provides guidelines for testing microphones in a vehicle. |
| A461466 2022584- | 2017-11-08. Service bulletin. STEERING; WHEELS; SERVICE BRAKES, HYDRAULIC. Supersedes Technical Service Bulletin Group 46 number 12-23 dated June 18, 2012. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. Document contains the brake pulsation diagnostic guidelines. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.