Service bulletins for the 2009 Audi A8
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
452 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| A961367 2019260- | 2017-12-05. Service bulletin. EQUIPMENT:ELECTRICAL. Supersedes Technical Service Bulletin Group 96 number 12-37 dated June 11, 2012. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer's door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 Model Years 2005 - 2006 and A3 Model Year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer's HomeLink® opener system is using an alternate code. The handheld transmitter's programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal. |
|---|---|
| A911392 2030947- | 2017-12-05. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 91 number 12-61 dated September 25, 2012. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype®, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone gets the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call assuming the phone is not responding. |
| A871343 2020124- | 2017-12-05. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Supersedes Technical Service Bulletin Group 87 number 13-42 dated June 11, 2013. Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Audi Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255. |
| A481346 2021191- | 2017-12-05. Service bulletin. STEERING. Supersedes Technical Service Bulletin Group 40 number 09-06 dated August 3, 2009. Customer hears squeaking noises when turning or maneuvering the steering wheel. The folds of the outer CV joint rubber boots can touch each other when the steering wheel is turned. |
| A461347 2034387- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM; PARKING BRAKE. Customer may report sporadically hearing the parking brake being actuated after the vehicle has been switched off. If the customer does not identify the sound as the sound of the parking brake being actuated, he or she may simply complain of hearing noises from the rear brakes. Ignition is switched off. Steering is locked. Park is selected. Parking brake is not engaged. If the electro-mechanical parking brake is not operated for some time, the free play between brake pads and brake discs increases because of normal brake pad wear. The parking brake control unit performs an automatic correction about every 621 miles (1,000 km). On A8 models, the brake pad thickness is also calculated. |
| A371309 2028715- | 2017-12-05. Service bulletin. POWER TRAIN. Supersedes Technical Service Bulletin Group 37 number 12-40 dated February 28, 2012. Rough gear changes, both when accelerating and when slowing down. There is a rough driving power disruption that occurs sporadically and lasts for less than a second. After a mechatronics, torque converter, or complete gearbox replacement, the clutches must be adapted to the new component. This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted. |
| A911374 2024323- | 2017-11-17. Service bulletin. BACK OVER PREVENTION: CAMERA SYSTEM. Supersedes Technical Service Bulletin Group 91 number 12-61 dated October 1, 2012. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions. |
| A571382 2017082- | 2017-11-17. Service bulletin. LATCHES/LOCKS/LINKAGES; EQUIPMENT:ELECTRICAL. Supersedes Technical Service Bulletin Group 57 number 11-55 dated August 22, 2011. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders. |
| A441336 2022563- | 2017-11-17. Service bulletin. SUSPENSION. Supersedes Technical Service Bulletin Group 44 number 13-35 dated January 18, 2013. Customer feels vibration from 55 - 80 mph (88 - 128 km/h) in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not result in any handling concerns or loss of vehicle control. |
| A481343 2015819- | 2017-11-17. Service bulletin. STEERING:ELECTRIC POWER ASSIST SYSTEM. Supersedes Technical Service Bulletin Group 48 number 11-15 dated January 10, 2011. The customer may report that the Easy Entry function of the power adjustable steering column intermittently does not work. |
| A461335 2017130- | 2017-11-17. Service bulletin. SERVICE BRAKES. Supersedes Technical Service Bulletin Group 46 number 11-16 dated December 9, 2011. Customer complains of brake squeal. |
| A431314 2018765- | 2017-11-17. Service bulletin. SUSPENSION:REAR:SPRINGS:AIR SUSPENSION SYSTEM; SUSPENSION:FRONT:SPRINGS:AIR SUSPENSION SYSTEM. Supersedes Technical Service Bulletin Group 43 number 12-11 dated October 29, 2012. The self-leveling system can no longer be adjusted with the MMI. The compressor for the self-leveling system continues to run after the engine has been switched off and the vehicle has been locked. DTCs may be stored in the level control system module, J197 (address word 34). Because of poor performance or failure of the air suspension compressor, the vehicle ride height cannot be adjusted. As a safeguard, the control module will lower the vehicle to the lowest position and illuminate the warning light. Drivability is not affected. |
| A001348 2002047- | 2017-11-17. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Supersedes Technical Service Bulletin Group 00 number 11-19 dated April 8, 2011. This TSB contains information on technician preparation when calling the Audi Technical Assistance Center |
| A191335 2025303- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 11-19 dated February 10, 2011. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service. |
| A571385 2017082- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM; LATCHES/LOCKS/LINKAGES:DOORS:LATCH. Supersedes Technical Service Bulletin Group 57 number 13-82 dated February 5, 2013. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders. |
| A961501 2019260- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 96 number 13-67 dated July 10, 2013. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer?s door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 model years 2005?2006 and A3 model year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer?s HomeLink® opener system is using an alternate code. The handheld transmitter?s programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal. |
| A481567 2017266- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 48 number 14-62 dated September 23, 2014. Electrically-adjustable steering column adjustment is restricted and does not adjust vertically. Incorrect operation of Easy Entry is not the cause. It is unlikely that external forces have led to the loss of the stored end positions of the adjustment movement. See TSB 2015819, 48 Easy Entry function of the power adjustable steering column intermittently does not work, for more information. Seat adjustments can be used to maintain the 10-inch minimum recommended distance from the steering wheel in case of airbag deployment. The axial adjustment is still functional during this condition. The steering column may be under tension due to unfavorable tolerances of the steering column and module cross carrier. As a result, the current draw of the regulator motors is above specification, which causes the electric steering column adjustment to fail. Once the vehicle electrical system control module, J519 (address word 09), detects an excessive current draw, the basic settings will be erased. If basic settings are not stored in the vehicle electrical system control module, the module will not send voltage/current to the motor to operate the vertical adjustment. |
| A191562 2025303- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 15-61 dated July 7, 2015. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service. |
| A171565 2038129- | 2017-11-17. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 17 number 15-63 dated June 2, 2015. A check with the engine oil service dipstick T40178 is necessary, but the adjustment values for the dipstick are not available in the Elsa repair manual. Because of a system change, the adjustment values for the service dipstick T40178 were removed from the repair manual. |
| A911518 2016513- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. Supersedes Technical Service Bulletin Group 91 number 10-59 dated September 15, 2010. In Mix (shuffle) mode, very long response times and subsequent malfunctions occur when the next track is being selected. Long response times also occur when the ?Return? hard key is pressed. In Mix (shuffle) mode, the previous track is not played when the ?Previous? button is selected in the CD control menu. A different track plays instead. In Mix (shuffle) mode, when the first track of the playlist was selected via the ?Previous? button in the CD control menu (rather than with the rotary push button), the track list shown in the MMI does not match the track list shown in the driver information panel (synchronization issue). In Mix (shuffle) mode, the current track is not highlighted in white letters in the MMI display. If the current track is selected again via the rotary push button, the audio briefly drops out. The current track is not color-highlighted in the MMI display. Audiobook tracks continuously fast-forward if ?Fast Forward? was selected in the first few seconds after the track started playing. The message ?Device is being initialized. Please wait?? is displayed when a second generation iPod Nano is installed. iPod locks up but is operable again after the iPod is reset. iPod performs a reset and restarts on its own. iPod is not detected when it is plugged into the AMI. The message ?Device or cable type not supported? appears in the MMI display. An automatic iPod upgrade through iTunes contained inoperative driver software. The customer may not realize that the iPod was updated and may complain that the AMI software is causing the issues. Because downgrading the updated iPod software is usually not possible, the AMI driver software (firmware) must be updated. The firmware update of AMI is not a ZUG update. Unlike ZUG updates, which are performed with an update CD in the CD changer, this firmware update is performed with a USB device connected dir |
| A461525 2022584- | 2017-11-17. Service bulletin. STEERING: STEERING WHEEL/HANDLE BAR; SERVICE BRAKES, HYDRAULIC. Supersedes Technical Service Bulletin Group 46 number 14-86 dated July 14, 2014. DO NOT use this TSB if there is another TSB for same concern applicable to the VIN. This TSB is only intended for diagnostic purposes and does not serve as a guideline for determining warrantable conditions. Customer may report that the steering wheel vibrates or pulsates when the brakes are applied. driving style, environmental conditions, and service history of the vehicle. Additionally, as brake pads and discs wear, their dampening ability is reduced. Disc thickness variation (DTV) is a common condition that contributes to brake pulsation. DTV occurs when the two braking surfaces of the brake disc are no longer parallel to each other. This condition cannot be accurately measured with normal workshop tools. |
| A441557 2022563- | 2017-11-17. Service bulletin. SUSPENSION. Supersedes Technical Service Bulletin Group 44 number 14-56 dated December 8, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. Customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. Tires with higher mileage and/or wear should be inspected to determine the best correction for the issue (repair or replacement). Tire life and condition should be determined prior to starting any diagnosis or repair for a vibration. |
| A911529 2013422- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 91 number 13-04 dated September 11, 2013. The Bluetooth® telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present. |
| A911526 2042097- | 2017-11-17. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). The traffic feature in the MMI navigation is inoperative. If the vehicle is a model year 2016 A6 or A7, see TSB 2042013: 91 Audi connect online destination search, Google Earth navigation view, or INRIX online traffic is not available. There is a known server issue that can only be resolved through a change to the Audi AG backend server. Audi has changed traffic providers over the years as new technologies have developed. This bulletin provides an overview of the different systems and the basic checks that can be performed to diagnose complaints related to traffic in the MMI navigation system. |
| A401549 2018194- | 2017-11-17. Service bulletin. SUSPENSION:FRONT:SHOCK ABSORBER; SUSPENSION:REAR:SHOCK ABSORBER. Supersedes Technical Service Bulletin Group 40 number 14-41 dated July 2, 2014. Oil appears on one or several shock absorbers. Oil may appear on a shock absorber As a result of a leak because the shock absorber is damaged. Oil may appear on a shock absorber As a result of residue from when the shock was filled during production, or as a result of slight condensation in the seal area. This small amount of oil is for lubrication and it reduces wear on the seal. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.