Service bulletins for the 2009 Audi A8
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
452 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| A201559 2011703- | 2017-11-17. Service bulletin. FUEL SYSTEM, DIESEL; FUEL SYSTEM, GASOLINE. Supersedes Technical Service Bulletin Group 20 number 13-29 dated November 15, 2013. The fuel tank has been removed from the vehicle and must be neutralized before shipment or disposal. When the fuel tank in a vehicle is replaced, the original tank must be properly flushed to neutralize the remaining gasoline or diesel fuel. |
|---|---|
| A171568 2028440- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; FUEL SYSTEM, GASOLINE:STORAGE:TANK ASSEMBLY. Supersedes Technical Service Bulletin Group 17 number 14-49 dated April 3, 2014. When the vehicle is completely refueled, the vehicle range (?distance to empty?) that is displayed is different than the vehicle range that was displayed the last time the vehicle was completely refueled. The displayed vehicle range drops inconsistently. After the vehicle is refueled, the displayed vehicle range does not change for a long period of time. When the vehicle is driven on hilly roads for a long period of time, the displayed vehicle range suddenly changes by a significant amount. There are no DTCs related to fuel senders stored in the instrument cluster control module, J285 (address word 17). This condition does not involve or affect the accuracy of the fuel level indicator, but only the estimated distance to empty display on the on-board computer. |
| A001578 2021205- | 2017-11-17. Service bulletin. EQUIPMENT:OTHER:LABELS. Supersedes Technical Service Bulletin Group 00 number 10-05 dated June 14, 2010. VIN plate and/or B-Pillar Safety Certification label requires replacement. |
| A011309 2014753- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE. Supersedes Technical Service Bulletin Group 00 number 10-01 dated February 5, 2010. Excessive accumulation of deposits on intake valves, intake manifold, fuel injectors and combustion chambers. Engine runs rough after cold start. Excessive engine cranking time. Hesitations while driving. Rough engine idle. Reduced engine performance. Poor fuel economy. Conditions may be severe enough to illuminate the MIL in conjunction with storage of DTCs for misfire (example: P0300, P030x) and / or lean fuel system (example: P0171, P0174, P1128, P1130, P1136, P1138) in the engine control module (ECM). Condition may be caused by use of contaminated gasoline. Condition may be caused by use of gasoline with a low content of deposit control additives. |
| A191341 2025303- | 2017-11-17. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 19 number 13-35 dated March 25, 2013. Discontinuation and mixing of Audi-approved engine coolants. G11, G12, and G12+ coolants have been replaced by an improved version. G12++ coolant (for service available) has been introduced in MY 2005 for all engines. G13 has been introduced in MY 2008 as factory filling and service. |
| A871342 2020124- | 2017-11-17. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; ELECTRICAL SYSTEM:12V/24V/48V BATTERY. Supersedes Technical Service Bulletin Group 87 number 12-37 dated November 16, 2012. Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Audi Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255. |
| A401227 2024318- | 2017-11-08. Service bulletin. SUSPENSION:FRONT:WHEEL BEARING. Supersedes Technical Service Bulletin Group 40 number 12-26 dated September 26, 2012. Clicking or clacking noise when maneuvering or parking. Normal driving dynamics may cause microscopic movements between the wheel bearing and wheel bearing housing. |
| A871237 2020124- | 2017-11-08. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 87 number 12-32 dated September 5, 2012. Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C Pressure/Temperature Sensor G395 leaks refrigerant. This causes Sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the J519 Central Electrics Control unit to Sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Audi Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of Vehicle Electrical System Control Module J519. Vehicle Electrical System Control Module J519 transfers the information provided by the sensor via the comfort data bus to Climate Control Module J255. |
| A011255 2030192- | 2017-11-08. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. MIL light on. P2015 sender of intake manifold flap position/air flow control, implausible signal P2020 sender of intake manifold flap position, intake manifold flap 2, implausible signal. Engine may have reduced performance without significant loss of power or stalling. Check service history to see if the improved ? B? suffix V157 Intake Flap motor has already been installed previously; if yes, only replace the potentiometer seals as described below. The fault entry is made because a linkage of the intake manifold flap adjustment sticks. This is caused by deformed oil seal behind the potentiometers. |
| A171232 2018550- | 2017-11-08. Service bulletin. ENGINE. Supersedes Technical Service Bulletin Group 17 number 12 - 31 dated August 30, 2012. Oil consumption measurement - Repair Authorization (CA). In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine and may change significantly over the life of the engine. Typically engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner's Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, the ambient temperature and road conditions. Additional factors are the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. |
| A431211 2018765- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 43 number 12-08 dated February 2, 2012. The self-leveling system cannot be adjusted any more with the MMI. The compressor for the self-leveling system continues to run after switching off the engine and locking the vehicle. DTCs may be stored. Because of poor performance or failure of the compressor for air suspension, the vehicle position cannot be adjusted. As a safeguard, the control module will lower the vehicle to the lowest position and illuminate the warning light. Drivability is not affected. |
| A911262 2024323- | 2017-11-08. Service bulletin. BACK OVER PREVENTION. Supersedes Technical Service Bulletin Group 91 number 10 - 60 dated September 28, 2010. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions. |
| A911263 2021151- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:APPLIANCE:AIR CONDITIONER. Supersedes Technical Service Bulletin Group 91 number 11 ? 83 dated April 15, 2011. The customer may report that the illumination of the dash insert, the air conditioning control panel or the inside light flickers when briefly pressing the accelerator in P or N or when shifting down while driving downhill. Only vehicles with PR number 8GH may be affected. When high electricity consumers are switched off and the battery is fully charged, the energy generated by the alternator is sometimes too great for the power system to absorb. This may lead to briefly increased voltage, and the lights mentioned above may briefly flicker. This characteristic is caused by the alternator design and is a normal condition of the vehicle. |
| A941292 2012749- | 2017-11-08. Service bulletin. EXTERIOR LIGHTING. Supersedes Technical Service Bulletin Group 94 number 11-52 dated October 11, 2011. Condensation is visible on the inside of the headlight, taillight, fog light, side marker light, front turn signal, daytime running lights, or third brake light lens. Damp air settles on the inside of a cold lens, which creates condensation. The headlight circulation system allows air from the outside to flow through the headlights. This open waterprotected ventilation system (needed for pressure compensation) creates different climate zones in the headlight: very warm areas, where the lens is warmed up by the light, and relatively cool areas, where the lens is cooled own by the air flow. Considerable differences in humidity and temperature between the inside and the outside of the headlights, even while driving, can lead to condensation. This is especially true in cold and wet weather, but it can also happen after a car wash, after steam cleaning the engine or the front end, with overnight temperature changes, etc. This phenomenon is more visible on lenses made of clear glass than on lenses with patterns. The moisture does not affect the headlight function (light performance) and does not lead to corrosion or other damage to headlight parts. |
| Email - Counterf | 2017-11-08. Service bulletin. AIR BAGS. On October 10, 2012, the National Highway Traffic Safety Administration released a press release regarding the potential for some vehicles to be at risk for containing counterfeit airbags if the airbags in the vehicle were replaced at independent repair shops that are not Audi dealerships or Audi certified. The Audi vehicles listed by NHTSA as at risk vehicles for the potential of containing counterfeit airbags if the airbags have been replaced are MY 2006-2009 A3, A4, A6, A8, Q5, and Q7 vehicles. If a Customer purchased their vehicle new, or if the vehicle is Certified pre-owned and a CARFAX report shows the airbag has never been replaced, there is no issue. |
| A901238 2032113- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. The customer may state that the outside ambient temperature display is incorrect. To achieve a smoothening effect of the displayed outside ambient temperature, the value shown does not instantaneously follow the temperature sensor measurement. The display will not change faster than 4° F (2° C) per minute. This concept applies to both falling and rising temperatures. A programming strategy is also implemented to avoid incorrect readings on a parked vehicle, due to the temperature sensor being affected by outside influences such as radiant heat from the engine bay, elevated road surface temperatures, etc. |
| A941200 2024877- | 2017-11-08. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM; EXTERIOR LIGHTING:HEADLIGHTS. Supersedes Technical Service Bulletin Group 94 number 12-83 dated July 9, 2012. Warning light for dynamic headlight range control is displayed in the instrument cluster. DTC 00003 / 14 (Control unit faulty) is registered in the dynamic headlight range control unit, address word 55. Both headlights function normally. Vehicles equipped with adaptive (cornering) lighting. New software version 0010 in the dynamic headlight range control module addresses this condition. If the headlight range control module has a software version lower than 0010 installed, then use the SVM code listed in Service to update the module. Some control units will already have software version 0010 installed but can still exhibit the conditions mentioned above. When this occurs, the software will need to be reflashed using a separate SVM code. The corrupt software will be overwritten. The software version does not change after the update. |
| A911450 2018187- | 2017-11-08. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. Supersedes Technical Service Bulletin Group 91 number 13-02 dated August 30, 2013. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices. |
| A401441 2018194- | 2017-11-08. Service bulletin. SUSPENSION:FRONT:SHOCK ABSORBER; SUSPENSION:REAR:SHOCK ABSORBER. Supersedes Technical Service Bulletin Group 40 number 13-34 dated September 23, 2013. Oil appears on one or several shock absorbers. |
| A401440 2023187- | 2017-11-08. Service bulletin. STEERING: STEERING WHEEL/HANDLE BAR. Supersedes Technical Service Bulletin Group 40 number 13-35 dated September 23, 2013. Squeaking noises are heard when the steering wheel is turned or maneuvered. The noises may be more prevalent in wet weather. The folds of the outer rubber boots on the front axle shafts may come in contact with each other when the steering wheel is turned, causing squeaking noises. These noises are more likely to occur when the vehicle is new. The volume and occurrence of the noise will dissipate after a short break-in period. |
| A001467 2002047- | 2017-11-08. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Supersedes Technical Service Bulletin Group 00 number 14-61 dated May 1, 2014. Technician preparation when calling the Audi Technical Assistance Center (TAC). |
| A001466 2037949- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated. This DTC is normal. It indicates that the parameter data has not been properly programmed into the ECU by SVM. |
| A001465 2011732- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 00 number 12-32 dated February 7, 2012. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update. |
| A441450 2022563- | 2017-11-08. Service bulletin. SUSPENSION; STEERING: STEERING WHEEL/HANDLE BAR. Supersedes Technical Service Bulletin Group 44 number 14-49 dated April 17, 2014. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration while driving at highway speeds from 55 ? 80 mph (88 ? 128 km/h). This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. If an applicable Repair Authorization is not followed, the claim will not be paid. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires or an imbalance of the wheel and tire assembly. |
| A371430 2003658- | 2017-11-08. Service bulletin. POWER TRAIN:CLUTCH ASSEMBLY:PEDAL/HAND LEVER(MOTORCYCLE). Supersedes Technical Service Bulletin Group 37 number 13-07 dated May 29, 2013. Customer states that the engine returns to idle speed of approximately 1,400 RPM although the accelerator is depressed, and/or the vehicle hesitates (lacks power on take-off). No DTCs are stored. This condition may be caused when the brake pedal and the accelerator pedal are depressed simultaneously. Drivers who drive with their left foot resting on the brake pedal are prone to experience this condition. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.