Service bulletins for the 2013 Audi A6
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
1666 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
By topic
Only bulletins with component: Software are shown. Show all
| A201554 2035073- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 20 number 15-52 dated October 28, 2015. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak. |
|---|---|
| A201552 2035073- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 20 number 15-48 dated October 15, 2015. The MIL is on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. The NVLD pressure switch may erroneously detect a very small leak. |
| A011545 2042071- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Engine warning lamp is illuminated. EPC lamp is illuminated. The engine runs irregularly. DTCs related to the cylinder on demand (COD) function are stored in the engine control module, J623 (address word 01). See the Service section of this bulletin for a complete list. A delay during the actuation of the COD adjusting mechanism is possible during the switch between 8 and 4 cylinder mode. |
| A901560 2042644- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. In vehicles with PR code 9Q7, display content is sporadically not shown in the driver information system and text is superimposed on the information line of the on-board computer. Incorrect software in the instrument cluster. |
| A011305 2033919- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 01 number 13-03 dated May 29, 2013. MIL on. DTCs are stored in the engine control module. There may be slight power reduction at high RPMs. One of the vacuum actuators on intake runner bank 1 or bank 2 is defective. |
| A011306 2033919- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 01 number 13-05 dated June 7, 2013. MIL on. DTCs are stored in the engine control module. There may be slight power reduction at high RPMs. One of the vacuum actuators on intake runner bank 1 or bank 2 is defective. |
| A011311 2033919- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 01 number 13-06 dated June 18, 2013. MIL on. DTCs are stored in the engine control module. There may be slight power reduction at high RPMs. One of the vacuum actuators on intake runner bank 1 or bank 2 is defective. |
| Dealer Letter - | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This communication is to inform you that Update 48K4 has been closed. We have turned off visibility for this Update while an alternate software solution is being developed. |
| A571402 2022032- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 57 number 13-97 dated October 29, 2013. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. The lock command history is stored in the convenience system control module (J393). |
| A011485 2036761- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 01 number 14-71 dated March 13, 2014. The MIL is on. DTC P164B(00) is stored in the engine control module.The oil pressure switch is defective. |
| A001466 2037949- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. A DTC with the description ?Invalid Data Record? is stored after an ECU has been replaced or updated. This DTC is normal. It indicates that the parameter data has not been properly programmed into the ECU by SVM. |
| A001465 2011732- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 00 number 12-32 dated February 7, 2012. This Technical Service Bulletin (TSB) details the general process for carrying out a Software Version Management (SVM) software update for any TSB or Update. |
| A641433 2029714- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 64 number 12-22 dated July 5, 2012. After one or both of the front door control units (J386/J387) is replaced, one or both of the rear door control units (J3888/J389) cannot be coded or parameterized via an SVM specified vs. actual comparison (spec/actual). The parameter data in the software coding container has changed for the front and rear door control units. As a result, an SVM code is required to update the parameter data for any replacement control unit. Simply running an SVM spec/actual will not code nor update the parameter data in the new replacement control unit. A hardware change suggestion will be provided when an SVM spec/actual is executed. An additional hardware replacement is not required. |
| A961483 2034000- | 2017-11-08. Service bulletin. LANE DEPARTURE: ASSIST; ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 96 number 13-78 dated October 31, 2013. Audi side assist deactivates or is sporadically inoperative. Message "Side Assist Unavailable" is displayed in the driver information system display when the system deactivates. Audi side assist deactivates or is sporadically inoperative. DTCs are stored in the Lane change assistance control module. A software issue within J769 causes a diagnostic fault, which deactivates the Audi side assist temporarily. |
| A911442 2036607- | 2017-11-08. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); ELECTRICAL SYSTEM:SOFTWARE. The GPS location or vehicle direction indicated on the navigation map does not match the actual vehicle's location or actual direction of travel. The condition can happen sporadically or consistently. The condition does not happen during or immediately following the initial PDI inspection (once the vehicle has been taken out of transport mode). It is normal for the satellite reception to be 0 immediately after taking the vehicle out of transport mode. With the ignition off, the vehicle must sit in open sky view for 10-15 minutes before a GPS fix can be obtained. The vehicle is a Model Year 2013. The MMI navigation unit uses internal sensors in the main unit and vehicle sensor data to determine the direction and movement of the vehicle. The GPS system provides supplementary position data upon vehicle start-up, when the vehicle has been off for less than four hours. If the vehicle has been off for more than four hours, a more accurate GPS 3D fix is required, as the previous GPS data is not used and has been thrown out. The GPS 3D fix is obtained when the system acquires four or more satellites. In areas with limited sky view or with tall obstructions, the system can take an extended amount of time to acquire four satellites, or may not be able to acquire the satellites at all until the vehicle is driven into an open sky view area. |
| A911441 2035919- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). Supersedes Technical Service Bulletin Group 91 number 13-17 dated December 3, 2013. The vehicle is a model year 2013 vehicle and TSB 2036607: 91 MMI3G+ Navigation GPS Location is inaccurate, has been completed. The GPS location or vehicle direction indicated on the navigation map does not match the vehicle's actual location or direction of travel. |
| A911437 2030947- | 2017-11-08. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 91 number 13-92 dated July 16, 2013. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype®, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone receives the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call because it assumes that the phone is not responding. |
| A911436 2027903- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 91 number 12-55 dated August 13, 2012. The most recent calls are not shown in the call lists of the vehicle. Call lists are not shown. The phone book (Directory) in the vehicle is not updated. The phone book is not downloaded to the vehicle. Vehicles with MMI 3G+ are affected. |
| A911427 2036575- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). The addresses and contacts stored in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus disappear intermittently in vehicles with MMI3G+ Navigation, and in vehicles with or without Audi connect. Intermittently, the MMI system does not appear to remember that the user's myAudi PIN has already been entered, and it requires the user to enter the PIN again in vehicles with Audi connect. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is paired to the vehicle, those addresses and contacts will only be visible any time that the same phone is paired to the vehicle. Any time that the same phone is not paired to the vehicle, the addresses and contacts will not be available. If a user stores addresses and contacts in the Navigation >> Favorites, Navigation >> Directory, and Navigation >> Last destinations submenus while a Bluetooth phone is not paired to the vehicle, the addresses and contacts will be available any time. In vehicles with Audi connect, the user is prompted to enter the myAudi PIN when selecting online destinations or when importing contacts from the myAudi account. If the user?s Bluetooth phone (the same phone that was paired to the vehicle when the PIN was entered initially) is paired to the vehicle, the user will not be prompted to re-enter the PIN after it has been entered. |
| A901447 2036132- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL. Supersedes Technical Service Bulletin Group 90 number 14-45 dated January 14, 2014. Customer may report that the head-up display (HUD) flickers or dims quickly. Software in the windshield projection head-up display control module, J898 (address word 82), causes incorrect brightness control. |
| A901445 2036132- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Customer may report that the head-up display (HUD) flickers or dims quickly. Software in the windshield projection head-up display control module, J898 (address word 82), causes incorrect brightness control. |
| A011456 2032900- | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 01 number 13-68 dated February 7, 2013. The MIL is on. DTC P008700 is stored in the ECM. The fault listed can occur under certain driving conditions. It is caused by an incorrect software setting. Some driving scenarios (such as extended idling or heavy stop-and-go traffic) can cause a slight misinterpretation of the data, which causes the MIL to illuminate. |
| Update Bulletin | 2017-11-08. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ELECTRICAL SYSTEM. Under certain conditions, permanent mode $0A DTC codes concerning the fuel pump power stage module may remain visible after the vehicle?s OBD system has run the proper monitors successfully to allow the DTC to be erased by the system, after a proper repair. This software malfunction may cause vehicle to not pass IM inspection programs. This software update eliminates specific permanent DTC codes stored in mode $0A of the ECM. All other DTC storage functions remain unaffected. This Update is in effect until removed. |
| Update Bulletin | 2017-11-03. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:SOFTWARE. Under certain conditions, permanent mode $0A DTC codes concerning the fuel pump power stage module may remain visible after the vehicle?s OBD system has run the proper monitors successfully to allow the DTC to be erased by the system, after a proper repair. This software malfunction may cause vehicle to not pass IM inspection programs. This software update eliminates specific permanent DTC codes stored in mode $0A of the ECM. All other DTC storage functions remain unaffected. This Update is in effect until removed. Procedure is valid only for vehicles that show the 24AD code in the ElsaWeb Campaign/Action Information screen on the day of repair. Vehicle must be within the Federal Emissions Warranty. Procedure must be performed within the allotted time frame stated in this Technical Service Bulletin. Procedure must be performed on applicable vehicles in dealer inventory prior to sale. |
| Dealer Letter - | 2017-11-03. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; ELECTRICAL SYSTEM. This communication is to inform you of upcoming Update 24AD. Under certain conditions, permanent mode $0A DTC codes concerning the fuel pump power stage module may remain visible after the vehicle?s OBD system has run the proper monitors successfully to allow the DTC to be erased by the system, after a proper repair. This software malfunction may cause vehicle to not pass IM inspection programs. This software update eliminates specific permanent DTC codes stored in mode $0A of the ECM. All other DTC storage functions remain unaffected. Update the ECM software to latest levels via SVM. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.