WenmarOpen by Wenmar Pro

Service bulletins for the 2010 Audi A5

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

892 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Only bulletins with component: Transmission control module are shown. Show all

Bulletins, newest first
37 14 46 20255352022-05-02. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); UNKNOWN OR OTHER; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. If the memory is read with guided fault finding (GFF) or if Immobilizer test plans are performed, the above DTC entries may be stored due to a communication error between the VAS tester and the TCM. (In particular, the issue happens with tester VAS 5051B).
37 14 26 20255352022-05-02. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); UNKNOWN OR OTHER. If the memory is read with guided fault finding (GFF) or if Immobilizer test plans are performed, the above DTC entries may be stored due to a communication error between the VAS tester and the TCM. (In particular, the issue happens with tester VAS 5051B).
37 13 08 20341632022-05-02. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM:SOFTWARE. Software error in the transmission control module. Customer may report that the transmission does not work correctly. ? Shortly after a cold start, the following message appears in the instrument cluster display: ?Gearbox Malfunction! Journey can be continued?. The gearbox is in limp mode until the key is cycled. ? The issue is very sporadic and cannot be reproduced with a test drive. ? DTC P17E1 (Gear positioner 2 mechanical malfunction) with DFCC 9473 is stored in the transmission control module, J743 (address word 02). ? The DFCC is the 4-6 digit code that is typically listed before the fault code (Figure 1).
37 12 75 20298082022-05-02. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). New software in the Transmission Control Module (J217) addressed the condition.
A971442 2036764-2017-11-08. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 97 number 14-41 dated March 18, 2014. The MIL is on. Vehicle will not start. DTC P068A00 is stored in the engine control module (ECM), J623 (address word 01). Numerous unrelated DTCs are also stored in the system, including: P056200, P057100, P068700, P068A00, P162400, P190C00, U010000, U010100, U012100, U014600, U015500, U021200, U101100, U102600, U111100, U111300, U140000, VAG00003, VAG00185, VAG00263, VAG00317, VAG00384, VAG00446, VAG00456, VAG00457, VAG00466, VAG00473, VAG00532, VAG00565, VAG00591, VAG00714, VAG00819, VAG00955, VAG01217, VAG01299, VAG01314, VAG01315, VAG01317, VAG01320, VAG01330, VAG01331, VAG01332, VAG01334, VAG01333, VAG01336, VAG01705, VAG01964, VAG02067, VAG02072, VAG02095, VAG02103, VAG02203, VAG02214, VAG02635, VAG02812, VAG02874, VAG03041, VAG03157, VAG03166, VAG03220, VAG03278, and/or VAG03531. The motronic engine control module power supply relay, J271, is not functioning properly. Because the J271 relay controls battery voltage (Terminal 30) via a ground signal sent from the ECM, numerous faults can occur in multiple control modules when it is not functioning properly.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.