Service bulletins for the 2008 Audi A5
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
487 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| A401443 2035854- | 2017-12-05. Service bulletin. SUSPENSION. Supersedes Technical Service Bulletin Group 40 number 14-42 dated July 8, 2014. A rattling or knocking noise is heard when the car is driven over bumps or uneven road surfaces. This noise is heard after the car has been driven for a while and is warmed up, and when the temperature outside is warm. This condition can be duplicated if the brakes are applied while the car is being driven over bumpy roads. This condition is a comfort concern. Vehicle handling is not affected. This bulletin applies only to vehicles equipped with 75mm hydro-bushings. This bulletin does not apply to vehicles equipped with 65mm bushings. High ambient temperatures at the hydraulic guide links cause the noise. |
|---|---|
| 2013_06_ATU Anal | 2017-12-05. Service bulletin. STRUCTURE:BODY:DOOR; VISIBILITY:POWER WINDOW DEVICES AND CONTROLS. This document contains information on analyzing squeaking windows on frameless doors. |
| 2013_06_ATU Audi | 2017-12-05. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This document contains information on the Audi side assist update. |
| 2013 06 Audi Bra | 2017-12-05. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; SERVICE BRAKES. This document contains information on the Audi braking guard. |
| A261319 2027945- | 2017-12-05. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM. Supersedes Technical Service Bulletin Group 26 number 13-18 dated May 22, 2013. Humming or metallic rattling noise from under the vehicle, heard most consistently during engine idle or slow acceleration. Initial inspection indicates that the noise is coming from the exhaust system. Relative movements in the rear mounting of the exhaust system (rear silencer). |
| A481348 2021191- | 2017-12-05. Service bulletin. STEERING. Supersedes Technical Service Bulletin Group 48 number 13-46 dated July 22, 2013. Customer hears squeaking noises when turning or maneuvering the steering wheel. The folds of the outer CV joint rubber boots can touch each other when the steering wheel is turned. |
| A571392 2022032- | 2017-12-05. Service bulletin. LATCHES/LOCKS/LINKAGES:DOORS:LATCH. Supersedes Technical Service Bulletin Group 57 number 11-49 dated August 8, 2011. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle "locked itself". The lock command history is stored in the convenience system control module (J393). |
| A641329 2020552- | 2017-12-05. Service bulletin. VISIBILITY:WINDSHIELD. Windshield is streaked, has a snakeskin appearance, or its surface feels rough. Residue from industrial fallout as well as normal road dirt and grime may accumulate on windshield. |
| A871344 2020124- | 2017-12-05. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Supersedes Technical Service Bulletin Group 87 number 13-43 dated July 12, 2013. Air conditioning is inoperative. The HVAC blower functions normally. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255. |
| A911302 2018187- | 2017-12-05. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. Supersedes Technical Service Bulletin Group 91 number 11-20 dated October 21, 2011. Customer may report that cracking, grinding, rattling, humming, whining, or similar interference is coming from one or more speakers. Parts of the speakers (such as the brackets, cables, or covers) or parts of the interior fittings (such as door covers, rear shelf, facings, or covers) can vibrate at certain frequencies, causing noises. The radio tuner or other control modules may be affected by electromagnetic interference from aftermarket electronic devices. |
| A911393 2034784- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE; EQUIPMENT:ELECTRICAL. Some telephone numbers that were downloaded via Bluetooth® are stored with additional, unrelated numbers that do not appear in the contact on the customer"s cellular phone. These telephone numbers are displayed incorrectly on the radio display. The software incorrectly stores the downloaded phone numbers. |
| A961367 2019260- | 2017-12-05. Service bulletin. EQUIPMENT:ELECTRICAL. Supersedes Technical Service Bulletin Group 96 number 12-37 dated June 11, 2012. The customer may report that the handheld transmitter cannot be programmed to the garage door opener control module, J530. The customer's door opener system may not be compatible with J530. The battery in the handheld transmitter may be too weak for a good signal. The battery charge may be sufficient to operate the garage door opener, but not enough to program the remote transmitter to the vehicle system. In A4 Model Years 2005 - 2006 and A3 Model Year 2009, the actual location of the garage door opener control module differs from the location shown in the owner's manual (opposite side of front bumper). The customer may misunderstand the programming procedure, particularly if the customer's HomeLink® opener system is using an alternate code. The handheld transmitter's programming function may become inoperative, or the transmitter is too far away from J530. Interference prevents the communication between handheld transmitter and J530. If the vehicle flashes during the programming of a handheld transmitter, this does not necessarily indicate that the programming was successful; it only indicates that the vehicle has recognized and saved a signal. |
| A961368 2029384- | 2017-12-05. Service bulletin. EQUIPMENT:ELECTRICAL. Supersedes Technical Service Bulletin Group 96 number 13-64 dated June 20, 2013. The customer is able to program one or more of the Homelink buttons using their garage door remote, but after a few days or weeks, one or more of the programmed Homelink buttons no longer functions. The LED on the Homelink button that is no longer functioning now flashes slowly, indicating that no programming is stored. The customer's transmitter operates at 295Mhz. No DTCs are stored in any control units. At the workshop, the Homelink system can be programmed to the workshop garage door successfully. No trouble is found. The garage door opener control module, J530, was designed with an operational frequency range in which the 295Mhz frequency works correctly during the initial programming of the system. Over time, the transmitting frequency can drift out of range (especially in warmer climates), causing the system to lose its programming. |
| A911392 2030947- | 2017-12-05. Service bulletin. EQUIPMENT:ELECTRICAL; ELECTRICAL SYSTEM:SOFTWARE. Supersedes Technical Service Bulletin Group 91 number 12-61 dated September 25, 2012. The customer complains that when he or she is trying to place a phone call from the vehicle while using a Bluetooth®-connected phone, the phone call disconnects before it begins and an error shows on the MMI display. The message may be "Function not supported" or "Network error". The customer is using a phone with the Android operating system. In addition, Skype®, or another network-based communication software, is installed on the phone. Call can be placed directly from the phone without a problem. When the phone gets the request to place a call from the vehicle, a prompt appears on the phone asking the user to choose how the call should be placed. If the prompt is ignored, the MMI system disconnects the call assuming the phone is not responding. |
| A911388 2021780- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. Supersedes Technical Service Bulletin Group 91 number 10-70 dated October 26, 2010. Sequence of error messages are seen on the radio display screen after a CD was loaded into or removed from the internal CD drive. "Drive defective. The error could be corrected by resetting it (see radio system owner's manual). Otherwise, contact your Audi dealer." "The CD-drive is damaged and was therefore deactivated." The CD drive cannot be selected in the Source list and is described as "damaged." After the ignition is cycled or a radio reset performed, the CD drive is fully operational. DTC 00468 (CD-ROM Drive -R92- Faulty) is stored in the radio (address word 56). The DTC will be sporadic if the ignition has been cycled or a radio reset performed and will automatically be cleared after 40 ignition cycles without a reoccurrence. Only vehicles with the CAN-based generation 3 radio (Concert (PR 8UQ) or Symphony (PR 8YN)) are affected. |
| A871343 2020124- | 2017-12-05. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Supersedes Technical Service Bulletin Group 87 number 13-42 dated June 11, 2013. Air conditioning is inoperative. The HVAC blower functions normally. Battery discharged; however, when charged, there is no bus silence when vehicle ignition is off. The A/C pressure/temperature sensor, G395, leaks refrigerant. This causes sensor G395 to show an incorrect or implausible value when reading MVBs. An incorrect signal or a low refrigerant level in the system can cause the air conditioning compressor to deactivate. The LIN cable connecting the vehicle electrical system control module, J519, to sensor G395 is pinched or cut. This affects the A4/S4, A5/S5 Coupe and Cabriolet, and Audi Q5 vehicles. The A6 and A8 are not affected by this type of failure. The pressure sensor G395/G65 sends an incorrect signal that prevents bus silence and the battery is discharged. Sensor G395 is a LIN slave of the vehicle electrical system control module. The vehicle electrical system control module transfers the information provided by the sensor via the comfort data bus to the climate control module, J255. |
| A551332 2023967- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM:WIRING:FRONT UNDERHOOD; LATCHES/LOCKS/LINKAGES:HOOD:LATCH. Supersedes Technical Service Bulletin Group 55 number 13-30 dated May 28, 2013. "Low Oil Level" message is on in the DIS or MMI. The hood must be open for at least 30 seconds for a reset of this message to be performed. The message is not reset in the DIS/MMI because the hood has not been recognized as being opened due to an inoperative hood contact switch. |
| A481346 2021191- | 2017-12-05. Service bulletin. STEERING. Supersedes Technical Service Bulletin Group 40 number 09-06 dated August 3, 2009. Customer hears squeaking noises when turning or maneuvering the steering wheel. The folds of the outer CV joint rubber boots can touch each other when the steering wheel is turned. |
| A461351 2033674- | 2017-12-05. Service bulletin. SERVICE BRAKES. Supersedes Technical Service Bulletin Group 46 number 13-46 dated June 27, 2013. Brakes on vehicles produced before September 3, 2012 (calendar week 36 of 2012), squeak or squeal when used with light to moderate force. |
| A461347 2034387- | 2017-12-05. Service bulletin. ELECTRICAL SYSTEM; PARKING BRAKE. Customer may report sporadically hearing the parking brake being actuated after the vehicle has been switched off. If the customer does not identify the sound as the sound of the parking brake being actuated, he or she may simply complain of hearing noises from the rear brakes. Ignition is switched off. Steering is locked. Park is selected. Parking brake is not engaged. If the electro-mechanical parking brake is not operated for some time, the free play between brake pads and brake discs increases because of normal brake pad wear. The parking brake control unit performs an automatic correction about every 621 miles (1,000 km). On A8 models, the brake pad thickness is also calculated. |
| A371309 2028715- | 2017-12-05. Service bulletin. POWER TRAIN. Supersedes Technical Service Bulletin Group 37 number 12-40 dated February 28, 2012. Rough gear changes, both when accelerating and when slowing down. There is a rough driving power disruption that occurs sporadically and lasts for less than a second. After a mechatronics, torque converter, or complete gearbox replacement, the clutches must be adapted to the new component. This requires a gradual move of the clutch linings toward the optimal operating points in the most diverse load conditions. As a result, sporadic driving power disruptions lasting for less than a second or reduced shift comfort are possible over the first 500 miles. This is normal, and these issues will decrease over time. The issues can also occur if the adaptation values of the gearbox were deleted. |
| A941306 2017806- | 2017-11-17. Service bulletin. ELECTRICAL SYSTEM; EXTERIOR LIGHTING. Supersedes Technical Service Bulletin Group 94 number 12-79 dated June 6, 2012. Light bulb warning light and the message Vehicle lights: malfunction is displayed in the instrument cluster display. DTC 03280 (Light switch position implausible signal) is stored in the vehicle electrical system control module, J519 (09). Exterior lights are functioning properly. If the headlight switch is moved to an intermediate position and remains there, the light bulb warning light and the error message appear after approximately ten seconds. Once displayed, the message turns off after approximately five seconds. The light bulb warning light turns off only after the headlight switch is turned to a defined position, and the status of DTC 03280 is changed to sporadic. After 40 driving cycles without an implausible signal detected, the DTC is automatically cleared. |
| A911374 2024323- | 2017-11-17. Service bulletin. BACK OVER PREVENTION: CAMERA SYSTEM. Supersedes Technical Service Bulletin Group 91 number 12-61 dated October 1, 2012. Parking aid sporadically warns of obstacles when none exist. Parking aid is inoperative or provides constant warning. Various parking aid sensor fitting issues. Environmental conditions. |
| A571383 2021363- | 2017-11-17. Service bulletin. LATCHES/LOCKS/LINKAGES; EQUIPMENT:ELECTRICAL. Supersedes Technical Service Bulletin Group 57 number 11-48 dated July 25, 2011. Vehicle doors cannot be locked or unlocked using Advanced key. Vehicle cannot be started using the Start-Stop button. In Access/Start Authorization Control Module J518 (address word 05), DTC 03283 (Driver's side Access/Start Authorization Antenna Short Circuit to Ground), DTC 03284 (Right Access/Start Authorization Antenna Short Circuit to Ground) or DTC 00183 (Interior Access/Start Authorization Antenna 1 -R138-) are stored. Vehicle keys function properly otherwise, operating the door locks via the remote control as well as starting the vehicle using the ignition switch. |
| A571382 2017082- | 2017-11-17. Service bulletin. LATCHES/LOCKS/LINKAGES; EQUIPMENT:ELECTRICAL. Supersedes Technical Service Bulletin Group 57 number 11-55 dated August 22, 2011. Central locking via remote control does not work either sporadically or permanently. The locks can still be operated manually. Missing synchronization between the remote control key and vehicle because the battery has been disconnected or the battery of the remote control has been replaced. If other senders operate in the same frequency range (mobile phones, TV stations, wireless headphones, baby monitors, other vehicle remote controls, etc.), the remote control key may have been temporarily switched off because a clear identification of the remote control key is not possible. This is necessary to prevent an unintentional unlocking of the vehicle by other unrelated senders. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.