Service bulletins for the 2014 Audi A4 allroad
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
645 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| A961377 2035047- | 2017-10-31. Service bulletin. LANE DEPARTURE. Supersedes Technical Service Bulletin Group 96 number 13-72 dated August 26, 2013. Audi Lane Change Assistant deactivates or is sporadically inoperative when the vehicle is driven in slowmoving stop-and-go traffic, especially on roads with multiple lanes. The message "Audi side assist unavailable: Sensors blocked" appears in the driver information system. The system is able to be activated approximately ten minutes after the traffic condition is removed, or after an ignition cycle. Audi Lane Change Assistant can be activated without issue. No obstructions can be found. DTCs are stored in the Lane Change Assistance control module. The control module mounting brackets are securely fastened to the lower rear bumper, and no damage is found to the rear bumper area, on the inside or outside. (If any damage is found, it is not covered under warranty.) The control module mounting brackets are not broken or loose. If a loose bracket is found, repair as necessary using the Elsa Repair Manual. Submit a separate warranty claim, as this TSB does not cover this repair. |
|---|---|
| A911308 2028190- | 2017-10-31. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Supersedes Technical Service Bulletin Group 91 number 11-28 dated December 9, 2011. Customer is inquiring about retrofitting the MMI system with a language pack or map database outside of factory-available options. |
| A911304 2013422- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 91 number 12-49 dated July 31, 2012. The Bluetooth® telephone cannot be connected to the vehicle?s Infotainment system. Certain restrictions are present when a Bluetooth device is connected to the vehicle. The restrictions vary depending on the vehicle system present. |
| A901341 2010353- | 2017-10-31. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. Supersedes Technical Service Bulletin Group 90 number 10-14 dated August 10, 2010. Cigarette lighter element will not lock into the lighter socket -U1- to begin the heating process, or the lighter element will not automatically release once the heating process has completed. As a result, the socket can become inoperative when used as a power outlet. |
| A871345 2024644- | 2017-10-31. Service bulletin. ENGINE AND ENGINE COOLING:COOLING SYSTEM:HOSES/LINES/PIPING/FITTINGS. Supersedes Technical Service Bulletin Group 87 number 13-41 dated May 30, 2013. Moisture in the driver or front passenger foot well. Due to a faulty and/or incorrectly installed condensation drain hose, condensation from the evaporator could enter the front foot well areas through a gap between the body and the sealing surface of the drain hose. |
| A801305 2033806- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM:WIRING. Supersedes Technical Service Bulletin Group 80 number 13-04 dated August 9, 2013. Malfunction Indicator Lamp is on. Climate system heating performance is insufficient. Coolant level warning is on. Engine temperature is elevated. ?Limp Home? mode is active. Faults are stored in the transmission control module. Coolant loss is found from one or more control valves: N82, N509, or N488. Coolant may have migrated into the wiring harness through the connector and into various control units. Climate system heating performance is insufficient due to coolant loss, or due to a faulty N82 control valve. Inspection of the coolant control valves N82, N509, or N488 reveals the presence of coolant inside the electrical connector as shown in the illustration. The connectors, wiring harness, and/or connected control units may have been damaged from exposure to coolant. |
| A721309 2035357- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. Seat memory function does not work. DTCs are stored. In the event of a voltage fluctuation in the vehicle power system, the software of the seat adjustment module fails. |
| A571394 2035367- | 2017-10-31. Service bulletin. EQUIPMENT. Various features in the rear passenger compartment are inoperative. Some features may include power rear windows, rear climate control operating unit, rear sunroof panel, rear reading lamps, rear cigarette lighters, etc. By design, many electronically-controlled features in the rear passenger compartment, in addition to the power rear windows, are deactivated if the child lock in the driver's door is activated. |
| A511307 2009967- | 2017-10-31. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. Supersedes Technical Service Bulletin Group 51 number 13-06 dated August 9, 2013. Instructions for vehicle inspection, protection removal, and detailing. |
| A481354 2028220- | 2017-10-31. Service bulletin. WHEELS; STEERING. Supersedes Technical Service Bulletin Group 48 number 12-30 dated June 25, 2012. Steering wheel appearance damaged due to external impact (e.g., contact with finger nails, zippers, watches, rings, etc.). External impact (e.g., contact with finger nails, zippers, watches, rings etc.) can cause damage to the appearance of the steering wheel. This type of damage is not warrantable, as numerous investigations have shown that there is no fault in material or workmanship. |
| A451307 2033412- | 2017-10-31. Service bulletin. STEERING. Supersedes Technical Service Bulletin Group 97 number 13-35 dated March 27, 2013. Steering wheel does not lock. Various warning lights are on. Steering feels stiffer than usual. The engine cannot be switched off. The ignition key cannot be removed. There are DTC entries present in the system (either static or sporadic). DTCs are stored in the ABS control module. This condition does not result in any drivability concerns. The steering system is fully connected. The insulation for the ABS wheel speed sensor is damaged in production. Over time, this can lead to corrosion on the wires and restricted functions with the ABS control module. Only the wires in the left bulkhead grommet are affected. |
| A441342 2022563- | 2017-10-31. Service bulletin. SUSPENSION; STEERING. Supersedes Technical Service Bulletin Group 44 number 13-36 dated February 18, 2013. This bulletin is not applicable if this vehicle has a Repair Authorization on this topic. Customer feels vibration in the seat, vehicle floor, footwell, pedals, or steering wheel. This condition does not lead to any handling concerns or loss of vehicle control. The customer feels the vibration in one or both of the following circumstances: * When driving at highway speeds from 55 - 80 mph (88 - 128 km/h). * When applying low brake pedal pressure with minor slow down. The vibrations felt by the customer could be a result of the harmonic vibrations caused by the radial force variation (RFV) of the tires. |
| A441341 2030194- | 2017-10-31. Service bulletin. STEERING; WHEELS. Supersedes Technical Service Bulletin Group 44 number 12-30 dated July 23, 2012. Complaints of steering wheel vibration and/or steering wheel oscillation at a speed range of 55 - 80 mph (88 ? 128 km/h), on vehicles with very low mileage or at PDI. The condition does not result in any handling concerns or loss of vehicle control. Vehicles have original factory-installed wheels and tires. Tire pressures on Audi vehicles are set to specified values in order to prevent flat spotting during the transportation process from various Audi plants to United States ports. To closely monitor complaints of tire-related vibration at very low mileage, we are asking that you contact the Audi Technical Assistance Center (TAC) before performing any repairs on vehicles with this condition. This will assist us in diagnosing any potential issues with the condition noted above. |
| A441340 2027779- | 2017-10-31. Service bulletin. STEERING. Supersedes Technical Service Bulletin Group 48 number 12-33 dated October 22, 2012. After replacing the electromechanical steering with the control unit J500, the unit cannot be coded via SVM spec/actual. All new replacement power steering control units (J500) must be coded and parameterized using online SVM spec/actual or an SVM code. If the SVM spec/actual returns a response of ?Check Hardware?, then the SVM code is required to code and parameterize the new replacement control unit. The SVM code can be found in Parts Bulletin 9-97, which is available online through ETKA. |
| A101310 2018288- | 2017-10-31. Service bulletin. ENGINE AND ENGINE COOLING. Supersedes Technical Service Bulletin Group 10 number 10-02 dated September 14, 2010. Prior to engine replacement, any debris lodged in transferred assemblies must be removed. If the vehicle's engine experienced a serious mechanical problem, it is possible that small pieces of metal debris resulting from the mechanical problem may have become deposited in the intake manifold, air intake hoses, exhaust manifolds, exhaust down-pipes, turbocharger, supercharger, and/or intercooler. If these pieces are not removed prior to the installation and operation of the replacement engine, the pieces may be drawn into the combustion chamber, which can cause a knocking noise and subsequent serious engine damage. |
| A011331 2035348- | 2017-10-31. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; ENGINE AND ENGINE COOLING. MIL on. Customer may report loss of performance. DTC P008700 (fuel rail pressure too low) may be stored in the engine control module, J623 (address word 01). Under extreme driving conditions with the A/C compressor switched off (e.g., long idle periods or extended stop-and-go traffic), high temperatures can build up in the fuel rail and may lead to fluctuations in fuel pressure, possibly causing DTC P008700 to be stored. Coolant temperature above 102?C in the freeze frame data can be an indicator of those extreme driving conditions. |
| A691326 2023323- | 2017-10-31. Service bulletin. AIR BAGS; ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 69 number 12-25 dated April 25, 2012. After the airbag control module (J234) has been replaced, the control unit cannot be coded via SVM spec/actual. An SVM code is required to code and parameterize the new service replacement airbag control module. Each model?s SVM code is provided in a parts bulletin (GP bulletin), which should have been referenced through ETKA when the module was replaced. The control module cannot be coded until the SVM code has been executed. |
| A571397 2022032- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM. Supersedes Technical Service Bulletin Group 57 number 13-92 dated August 1, 2013. The customer inquires about the operation of the vehicle locking, and may suggest that the vehicle ?locked itself?. The lock command history is stored in the convenience system control module (J393). |
| A271319 2029010- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. Supersedes Technical Service Bulletin Group 27 number 12-13 dated March 22, 2012. The customer may report a discharged battery when trying to start the vehicle. The condition results in a no start. |
| A271318 2023282- | 2017-10-31. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. Supersedes Technical Service Bulletin Group 27 number 12-10 dated February 13, 2012. Battery testing and charging for vehicles equipped with a Battery Data Manager (BDM - J367). When the InCharge 940 is used as a battery charger in auto mode, it performs a battery condition test and may prematurely fail the battery if the charging takes place at the jumper posts in the engine compartment. This is due to the added resistance in the system between the battery and jumper posts. When the InCharge 940 is used as a battery charger in manual mode, the battery condition test is not performed. |
| A201327 2035073- | 2017-10-31. Service bulletin. ENGINE. MIL on. DTC P045600 (EVAP System Leak Detected NVLD (very small leak)) is stored in the engine control module (ECM), J623 (address word 01). Drivability is not affected. |
| A171344 2035463- | 2017-10-31. Service bulletin. ENGINE AND ENGINE COOLING. In order to provide effective lubrication and cooling of internal engine components, all internal combustion engines consume a certain amount of engine oil. Oil consumption varies from engine to engine, and may change significantly over the life of the engine. Typically, engines with specified break-in periods consume more oil during the break-in period, and the oil consumption will stabilize after the break-in period. Refer to the Owner?s Manual for specific break-in procedures. Under normal conditions, the rate of oil consumption depends on the quality and viscosity of the oil, the RPM at which the engine is operated, and the ambient temperature and road conditions. Additional factors include the amount of oil dilution from water condensation or fuel residue and the oxidation level of the oil. Utilizing the advanced sensor technology integrated in models equipped with the 3.0 TFSI engine, it is possible to measure oil consumption electronically via a Guided Function test plan. If the electronic oil consumption test is not available for this model, perform the test with the conventional scale/oil weighing method. See TSB 2018550 for instructions for the conventional scale/oil weighing method. |
| A011339 2035348- | 2017-10-31. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER. Supersedes Technical Service Bulletin Group 01 number 13-31 dated September 25, 2013. MIL on. Customer may report loss of performance. DTC P008700 (fuel rail pressure too low) may be stored in the engine control module, J623 (address word 01). Under extreme driving conditions with the A/C compressor switched off (e.g., long idle periods or extended stop-and-go traffic), high temperatures can build up in the fuel rail and may lead to fluctuations in fuel pressure, possibly causing DTC P008700 to be stored. Coolant temperature above 102?C in the freeze frame data can be an indicator of those extreme driving conditions. |
| Executive Servic | 2017-10-27. Service bulletin. ENGINE; EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL; SERVICE BRAKES, HYDRAULIC:FLUID; POWER TRAIN; STEERING:HYDRAULIC POWER ASSIST:POWER STEERING FLUID. This document contains a fluid capacity chart as well as a chart that contains the parts and part numbers needed for service. |
| A971550 2034863- | 2017-10-27. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Supersedes Technical Service Bulletin Group 37 number 13-18 dated October 16, 2013. Customer may report that the gearbox warning message is on. DTC P0706 (driving mode sensor, implausible signal) is stored in the transmission control module (TCM), J217 (address 02). There is a reaction between the TCM and the automatic transmission fluid (ATF) in vehicles within a specific VIN range. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.