Service bulletin 007/97U

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	52495
Published by NHTSA	1997-08-14
Manufacturer's number	007/97U
Manufacturer's date	1997-05-19
NHTSA component	EQUIPMENT:APPLIANCE:AIR CONDITIONER

NHTSA's summary

A/C REFRIGERANT CHARGING. *TW

The document

No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.

Components

Equipment and accessories, Heating and air conditioning

Vehicles listed
MAZDA PROTEGE	1995, 1996, 1997

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
0901216	2022-06-06. Service bulletin. Paint damage Mazda pocket paint guide
0100516	2022-06-06. Service bulletin. Battery test procedure requirements using the GR81291
09-025-21-3824	2021-08-24. Service bulletin. This service bulletin provides information regarding the proper use of the driver’s floor mat to avoid any potential interference with the foot pedals. The following are possible causes of floor mat interference, which can be avoided with proper usage.
09-002-21-3770	2021-02-05. Service bulletin. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer
09-003-20-3671	2020-01-23. Service bulletin. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer’s responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. • Mazda vehicles are manufactured with tamper-proof speedometers. • When a speedometer is replaced, the new speedometer will read zero (0) miles. • This procedure is extremely important to accurately represent actual vehicle mileage. • Prior to speedometer removal, complete the information required on the “Speedometer Replacement Label”. Labels can only be ordered through Mazda eStore. • In an effort to achieve a higher level of Customer Experience and retain the value of Mazda’s vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO’s services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
00-003-19-3583	2019-03-21. Service bulletin. In support of the new MRT distribution, Mazda will ship to dealers a new Dual Purpose Diagnostic Leak Detector beginning March, 2019. Training videos will be posted to MGSS shortly and Workshop Manual procedures will be revised gradually.
09-002-19-3554	2019-02-19. Service bulletin. This service bulletin provides information regarding the proper use of the driver's floor mat to avoid anypotential interference with the foot pedals. The following are possible causes of floor mat interference,which can be avoided with proper usage. Floor mat moves forward due to improper installation. Inappropriate floor mat (such as aftermarket, non-factory-equipped, or non-genuine) is used. Floor mat is stacked one on top of another.
09-034-18-3430a	2018-11-13. Service bulletin. In accordance with Federal regulations, follow the procedure listed below when replacing a speedometer. NOTE: Tampering with a motor vehicle odometer is strictly prohibited by Federal, and State laws. It is the dealer's responsibility to comply with Federal, State, and local laws concerning odometer and related documentation requirements when providing a repair or replacement. Mazda vehicles are manufactured with tamper-proof speedometers. When a speedometer is replaced, the new speedometer will read zero (0) miles. This procedure is extremely important to accurately represent actual vehicle mileage. Prior to speedometer removal, complete the information required on the "Speedometer Replacement Label". Labels can only be ordered through Mazda eStore. In an effort to achieve a higher level of Customer Experience and retain the value of Mazda's vehicles, MNAO Warranty Operations is allowing all Mazda dealers to utilize a third party, SPECMO Enterprises, Inc., for Instrument Panel Cluster (IPC) odometer setting service. With the use of SPECMO's services, it is possible that the odometer will be set between 10 to 31 miles over the odometer mileage at the time of replacement for both warranty and customer pay repairs. Please make sure that the customer is aware that there may be a slight variance to the odometer, in which case the customer may have to accept the slightly higher mileage. Since odometer setting service is not part of the warranty repair, it is not warrantable nor required, but optional. However, Mazda Warranty policy provides after- warranty assistance (AWA) or DSA that can be utilized to cover this service expense.
09-014-18-3443a	2018-11-13. Service bulletin. When encountering a vehicle with paint damage, refer to the "Mazda Pocket Paint Guide" to determine cause, prevention, remedy, and warranty coverage (if applicable). Copies of the Mazda Pocket Paint Guide are available for order on Mazda e-Store (part number: 9999-95-MPPG-12).
00-003-18-3480a	2018-11-13. Service bulletin. Mazda North American Operations has approved an additional on-car brake lathe as an option for MNAO authorized equipment. The Pro-Cut On-Car Brake Lathe has been added to the MNAO authorized equipment program. NOTE: Accu-turn is still an approved brake lathe, but it is no longer available for purchase from our vendor. IMPORTANT: Rotors must be machined using a Mazda approved on-car brake lathe, or warranty claims are subject to denial or debit.