WenmarOpen by Wenmar Pro

Over-the-air update HVAC-22.AA.AC Bronco

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeOver-the-air update
NHTSA id11032713
Published by NHTSA2026-05-15
Manufacturer's numberHVAC-22.AA.AC Bronco
Manufacturer's date2026-05-08
Campaign id or software versionHVAC-22.AA.AC
NHTSA componentPOWER TRAIN; ENGINE; UNKNOWN OR OTHER

NHTSA's summary

Quality improvements include: - Optimizes cabin ventilation strategy at high speeds

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Engine, Transmission and driveline

Vehicles listed
FORD BRONCO2021, 2022

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
26V4680002026-07-20. ENGINE; ELECTRICAL SYSTEM:WIRING:FRONT UNDERHOOD
20261882026-04-15. Powertrain
26V2360002026-04-14. POWER TRAIN:AUTOMATIC TRANSMISSION
20244922024-08-23. Engine
24V6350002024-08-23. ENGINE AND ENGINE COOLING:ENGINE:HARD PARTS INTERNAL/MECHANICAL
23V0700002023-02-10. POWER TRAIN:AUTOMATIC TRANSMISSION

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
SSM 552282026-10-12. Service bulletin. Some 2020-2026 Aviator/Explorer/F-150/Bronco/Ranger vehicles equipped with a 2.7L or 3.0L (non-diesel) engine may need the front engine cover removed and reinstalled for various reasons. The Workshop Manual (WSM), Section 303-01 Engine > Removal and Installation > Engine Front Cover service procedure has been updated to include a new essential special service tool (ESST) guide pin alignment tool (303-1790) that is used to align the engine front cover to the engine block, preventing the O-ring seal on the engine oil galley feed tube from getting damaged during installation.
PCM-26.10.3 Bronco2026-09-21. Over-the-air update. 25S75 Recall remedy -Powertrain Control Module update to introduce logic to prevent low pressure fuel pump binding and maintain fuel flow to the engine.
SSM 550732026-08-11. Service bulletin. Some 2021-2026 Bronco vehicles may require the removal and installation of the transfer case for various reasons. Installation requires Loctite® 243 adhesive applied to the mounting bolt threads in the transmission. Make sure that the mating faces are clean and dry. Tightening the mounting bolts also requires an updated two-stage tightening sequence. Workshop Manual (WSM), Sections 307-07C/D and 308-07C/D Installation > Transfer Case have been updated to reflect this change.
TSB 26-22912026-06-22. Service bulletin. This bulletin supersedes 26-2006. Reason for update: update the Parts list to correct the ambient air temperature service part number. Some vehicles listed in the model statement above may require the replacement of the ambient air temperature sensor for various concerns. DTCs P0071, P0072, and/or P0073 may be present in the powertrain control module (PCM).
SSM 549022026-06-09. Service bulletin. For 20202026 vehicles equipped with the 10R60 transmission, a new Transmission Clutch Circuit Leak Test has been introduced in the Ford Diagnosis and Repair System (FDRS). This test utilizes the pressure and vacuum transducer (PVT) when available. Workshop Manual (WSM) updates related to this diagnostic procedure are planned for release in Q4 2026. The new test improves the accuracy of detecting leaks within transmission fluid circuits and replaces the previous air check method. The previous air check procedure has been shown to produce a high rate of false positives, which may lead to unnecessary repairs when no actual leak is present. Accordingly, the air check procedure is not to be used for diagnosing internal transmission hydraulic leaks or as justification for transmission replacement.
25B512026-06-05. Other. Certain 2021-2024 Model Year Bronco, 2021-2024 Model Year Bronco Sport, 2020-2022 Model Year Corsair and Escape, 2016-2024 Model Year Explorer, 2019-2020 Model Year Fusion, 2016-2018 Model Year Focus RS, 2022-2024 Model Year Maverick, 2016-2019 Model Year MKC and 2019-2024 Model Year Ranger Vehicles Equipped with a 2.0L or 2.3L Engine and Engine Block Heater System Block Heater Replacement
SSM 548182026-05-18. Service bulletin. Some 2021-2024 Bronco vehicles equipped with a manual transmission may experience a rotational scraping noise while the transmission is in neutral, 1st and/or 2nd gear with the clutch pedal released. The noise may be more noticeable in ambient temps below 10°C (50°F) and after a cold soak. This noise may also diminish as the transmission warms up. This may be due to the 5th and 6th gear synchronizer rings. The 5th and 6th gear synchronizer rings are now only available in the 6th/5th gear synchronizer assembly (service part number MU7Z-7124-Q). To correct the condition, replace the 6th/5th gear synchronizer. Remove the transmission from the vehicle. Refer to Workshop Manual (WSM), Section 308-03 > Removal. Disassemble the transmission. Refer to WSM, Section 308-03 > Disassembly. Disassemble the input shaft to gain access to the 6th/5th gear synchronizer. Refer to WSM, Section 308-03 > Disassembly and Assembly of Subassemblies > Input Shaft. Replace the 6th/5th gear synchronizer and assemble the input shaft. Assemble the transmission. Refer to WSM, Section 308-03 > Assembly. Install the transmission.
SSM 547812026-04-28. Service bulletin. Some 2021-2025 Bronco vehicles built on or before 09-Sep-2025 may require replacement of the ambient air temperature sensor for various concerns. Diagnostic trouble codes (DTC) P0071, P0072, and/or P0073 may be present in the powertrain control module (PCM). A concern has been identified in TSB 26-2006 that previously instructed replacement of the incorrect ambient air temperature sensor for the vehicle application. Monitor Professional Technician System (PTS) for updates.
TSB 26-20062026-04-22. Service bulletin. Some vehicles listed in the model statement above may require the replacement of the ambient air temperature sensor for various concerns. DTCs P0071, P0072, and/or P0073 may be present in the powertrain control module (PCM).
24N12 S22026-04-07. Other. Certain 2021 - 2022 Model Year Various Vehicles Engine Valve Inspection Test This submission includes : Technical Instructions Updated wording and description with additional photo.