Service bulletin SSM 53980
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 11020051 |
| Published by NHTSA | 2025-07-02 |
| Manufacturer's number | SSM 53980 |
| Manufacturer's date | 2025-06-24 |
| NHTSA component | ELECTRICAL SYSTEM |
NHTSA's summary
Some 2023-2025 F-Super Duty vehicles may exhibit multiple warning indicators with DTCs U0252, U0137, U0199, U0438 stored in the body control module (BCM), image processing module A (IPMA), power steering control module (PSCM), instrument panel cluster (IPC) and/or inoperative power windows and locks. This may be due to an incorrectly tightened ground 201 (G201). Inspect G201 for proper connection, locating tab insertion, and tighten to 8 +/- 1.2 Nm. If the condition remains after tightening G201, continue with normal Workshop Manual diagnostics.
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Electrical system
Trouble codes named
U0137, U0199, U0252, U0438
| FORD F-250 SD | 2023, 2024, 2025 (the catalog's model; the bulletin names a series or trim of it) |
|---|---|
| FORD F-350 SD | 2023, 2024, 2025 (the catalog's model; the bulletin names a series or trim of it) |
| FORD F-450 SD | 2023, 2024, 2025 (the catalog's model; the bulletin names a series or trim of it) |
| FORD F-550 SD | 2023, 2024, 2025 (the catalog's model; the bulletin names a series or trim of it) |
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| 26V104000 | 2026-02-20. EXTERIOR LIGHTING:TAIL LIGHTS; ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL |
|---|---|
| 25V540000 | 2025-08-22. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL |
| 23V506000 | 2023-07-21. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL |
A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.
| SSM 55239 | 2026-10-13. Service bulletin. Some 2023-2026 F-Super Duty vehicles equipped with a trailer brake control module and built on or before 08-May-2026 may exhibit a "Trailer Disconnected" message after cycling the ignition off and back on with a trailer connected. This may be due to the presence of an integrated battery charger on a trailer equipped with electric over hydraulic brakes. If trailer functionality is restored after unplugging and plugging the trailer connector back in while the ignition is on, this condition can be corrected by downloading and performing the "Trailer Brake Configuration" application using the latest software version of the Ford Diagnosis and Repair System (FDRS) scan tool. For claiming, use causal part 19H332 and labor operations 12651D and 12651D4. Workshop Manual (WSM), Section 417-01 Exterior Lighting > Diagnosis and Testing > Trailer Lamps > Pinpoint Test G The Message Center Displays A False Trailer Disconnected Message When A Trailer Is Connected To The Vehicle - Only For Electric Over Hydraulic (EOH) Equipped Trailers When Vehicle Trailer Brake Type Setting Is Set To Electric Over Hydraulic has bee |
|---|---|
| TSB 26-2375 v2 | 2026-10-13. Service bulletin. NOTE: This bulletin has been updated, refer to the change log at the bottom for details. Issue: Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: • Poor shift quality • Illuminated powertrain malfunction (wrench) indicator with DTCs P2704 and P0771 stored in the PCM / TCM . This may be due to a calibration in the TCM and/or wear between the input shaft and the E clutch hub causing theinput shaft O-rings to become damaged resulting in an open E clutch circuit. Action: For vehicles that meet all of the criteria in the Issue and Model statements, follow the Service Procedure toreprogram the PCM / TCM and/or replace the E clutch hub and input shaft O-rings |
| TCU-26.2.12.2.1 | 2026-09-21. Over-the-air update. Quality improvements include: -Addresses a bug that may cause updates to fail |
| ECG-26.2.12.3 Bronco,Esca | 2026-09-11. Over-the-air update. Quality improvements include: -ePrivacy enhancements |
| SSM 55118 | 2026-09-01. Service bulletin. Some of the following vehicles: * 2023-2025 F-Super Duty built on or before 02-Feb-2025 * 2024-2026 Ranger/Bronco/Mustang * 2024-2025 F-150 built on or before 15-Jul-2025 * 2024-2025 Nautilus built on or before 16-Feb-2025 * 2025 Explorer/Aviator built on or before 01-Feb-2025 may exhibit all of the following symptoms: - "No Key Detected" message displayed on the instrument panel cluster (IPC). - Key fob does not work in the backup slot. - Remote keyless entry (RKE) (lock and unlock from the key fob) functionality will work to lock/unlock the vehicle. If the vehicle exhibits these symptoms, start the vehicle using both key fobs. If the no crank/no start condition with "No Key Detected" concern is present, reprogram both key fobs and retest. If the no crank/no start condition with "No Key Detected" is still present, replace the body control module (BCM). Refer to Workshop Manual (WSM), Section 419-10. For claiming, use causal part 15604 and labor operation MT55118SSM up to 1.8 hours. |
| SSM 55116 | 2026-09-01. Service bulletin. Some of the following vehicles: * 2025-2026 Expedition/Navigator built on or after 02-Feb-2025 * 2025-2026 F-Super Duty built on or after 02-Feb-2025 * 2025-2026 Explorer/Aviator built on or after 02-Feb-2025 * 2025-2026 Nautilus built on or after 17-Feb-2025 * 2025-2026 F-150 built on or after 16-Jul-2025 may exhibit all of the following symptoms: - "No Key Detected" message displayed on the instrument panel cluster (IPC) - Key fob does not work in the backup slot. - Remote keyless entry (RKE) (lock and unlock from the key fob) functionality will work to lock/unlock the vehicle. If the vehicle exhibits these symptoms, manually enter the vehicle identification number (VIN) into the VIN entry dialog in the Ford Diagnosis and Repair System (FDRS) and then start a session using the Vehicle Communication Module (VCM) II, VCM 3, Vehicle Communication and Measurement Module (VCMM) or later level device with a universal serial bus (USB) cable disconnected from the laptop. Download the "BCM - Body Control Module (BCM) Hardware Test" app |
| TSB 26-2375 | 2026-08-19. Service bulletin. This article supersedes TSB 26-2050 to increase the labor operation allowance of labor operations A and B. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: Poor shift quality Illuminated powertrain malfunction (wrench) indicator with diagnostic trouble codes (DTC) P2704 and P0771 stored in the PCM/TCM. This may be due to a calibration in the TCM and/or wear between the input shaft and the E clutch hub causing the input shaft O-rings to become damaged resulting in an open E clutch circuit. Additional model information: 6.7L Diesel Engine 2022-2024 F-550 or F-600 F-Super Duty vehicles built on or before 15-May-2024 with over 5,000 miles (8,000km) |
| SSM 55031 | 2026-07-28. Service bulletin. Some 2021-2026 Ford/Lincoln vehicles may exhibit various symptoms including but not limited to the auto start/stop system not operating as intended with a "Check Charging System" message in the instrument panel cluster (IPC) while the charging system is operating properly with no charging related diagnostic trouble codes (DTC) stored. This may be due to someone using an aftermarket programmer to change the body control module (BCM) configuration to disable the auto start/stop system or perform other unsupported programming modifications. To correct this condition on F-150 and Bronco vehicles, download and run the Ford Diagnosis and Repair System (FDRS) application titled "BCM-Charging System Configuration Correction". Running this application will determine if the BCM configuration was modified by the customer and if so, provide the option to return the configuration back to factory settings. For other vehicle models exhibiting concerns related to unsupported aftermarket BCM programming, submit a Technical Support Request (TSR) requesting support to revert the BCM configuration |
| SSM 55021 | 2026-07-21. Service bulletin. Some 2025-2026 Bronco/Bronco Sport/Corsair/F-150/F-Super Duty/Maverick/Mustang/Mustang Mach-E/Ranger vehicles may exhibit a no audio/sound condition. This may be due to the software in the audio control module (ACM). To determine if it is a software concern, disconnect the vehicle's 12-volt battery cables for 10 minutes and reconnect. If the concern is still present, continue with normal diagnostics in Workshop Manual (WSM), Section 415-00 Information and Entertainment System > General Information > Diagnosis and Testing and repair as necessary outside of this article. If the no audio/sound concern is resolved, reprogram the ACM using the latest software level of the Ford Diagnosis and Repair System (FDRS). For claiming, use causal part 18C869 and labor operations 10654C, 12651D and 12651D4. |
| SSM 54979 | 2026-07-08. Service bulletin. Some 2023-2025 Mustang Mach-E and 2024-2026 F-Super Duty vehicles equipped with a 360-degree camera may exhibit a distorted or corrupted 360-degree camera image in the center display screen, but the rear-view camera image is operating correctly. To restore the 360-degree camera image, download and run the "IPMA - Reset the Image Processing Module A (IPMA) Calibration Data" application using the Ford Diagnosis and Repair System (FDRS) scan tool. Then download and run the "IPMA - 360 Degree View Camera Alignment" application. Inform customers that they can continue to drive the vehicle and engineering is currently working on a software solution for this condition that is expected in Q3 of 2026. Replacement or reprogramming of the IPMA will not resolve this condition. Monitor Professional Technician System (PTS) for additional information and schedule service appointments for customers once the repair becomes available. If a vehicle exhibits this condition, enter a vehicle identification number (VIN) and click the "Submit Global Concern Report (GCR)" link at the upper right of the PTS |