WenmarOpen by Wenmar Pro

Service bulletin SA-009-23g

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10241633
Published by NHTSA2023-09-05
Manufacturer's numberSA-009-23g
Manufacturer's date2023-08-15
NHTSA componentEXTERIOR LIGHTING; EQUIPMENT:ELECTRICAL:INFOTAINMENT; ENGINE AND ENGINE COOLING

NHTSA's summary

Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote function(s) inoperative. Engine Start / Stop, Door Lock / Unlock, Lights ON / OFF

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Engine, Equipment and accessories, Lighting

Vehicles listed
MAZDA CX-302020, 2021, 2022, 2023, 2024
MAZDA CX-52021, 2022, 2023, 2024
MAZDA CX-502023, 2024
MAZDA CX-92021, 2022, 2023
MAZDA CX-902024
MAZDA MAZDA32019, 2020, 2021, 2022, 2023, 2024
MAZDA MX-302022, 2023

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
20246572024-10-31. Engine
24V8150002024-10-31. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM)
24V6490002024-09-03. LANE DEPARTURE: SENSING SYSTEM: CAMERA; FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING; EXTERIOR LIGHTING:HEADLIGHTS
20234362023-08-04. Lights And Instruments
20231082023-03-02. Accessories
20193222019-06-27. Engine
19V4970002019-06-27. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); ENGINE
20192242019-05-14. Lights And Instruments

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
SA-061-262026-10-01. Service bulletin. DESCRIPTION Use this guide before ordering or replacing an AT component on applicable H3T vehicles. QUICK CHECKLIST BEFORE ORDERING Confirm the vehicle is a CX-90 (KK) or CX-70 (KJ) with H3T and is within the applicable market coverage. • In GEPC, identify the AT component part number for the vehicle. • Use the GEPC lookup tables below to determine whether the vehicle requires Table A or Table B parts. • Order the complete set of parts listed in the applicable table. DO NOT order the AT component by itself. • Check whether water hose removal is required for that GEPC part number. • Follow the applicable WSM repair procedure for AT component removal/installation, water hose removal, and oil hose/oil pipe installation in MGSS. • IMPORTANT: If only the AT component is ordered, required replacement parts will be missing, and the repair cannot be completed.
SA-059-262026-10-01. Service bulletin. This Service Alert supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-029/24 05/09/24 DESCRIPTION The CX-90 and CX-70 PHEV are equipped with two electric water pumps that look similar but have different part numbers. CAUTION: If the wrong water pump is ordered or they are reversed, DTC U019F could be set.
PF-26-042026-10-01. Other. SUBJECT: ORDERING REQUIREMENT FOR AT COMPONENTS FOR H3T (INLINE 6) Use this guide before ordering or replacing an AT component on applicable H3T vehicles. QUICK CHECKLIST BEFORE ORDERING • Confirm the vehicle is a CX-90 (KK) or CX-70 (KJ) with H3T and is within the applicable market coverage. • In GEPC, identify the AT component part number for the vehicle. • Use the GEPC lookup tables below to determine whether the vehicle requires Table A or Table B parts. • Order the complete set of parts listed in the applicable table. DO NOT order the AT component by itself. • Check whether water hose removal is required for that GEPC part number. • Follow the applicable WSM repair procedure for AT component removal/installation, water hose removal, and oil hose/oil pipe installation in MGSS. IMPORTANT: If only the AT component is ordered, required replacement parts will be missing, and the repair cannot be completed.
09-027-262026-10-01. Service bulletin. DESCRIPTION Some CX-70 and CX-90 PHEV vehicles may fail to start (enter READY mode) in cold weather, but the vehicle can often be started successfully on the next attempt. This may occur when leakage current between connector terminals causes the MAIN Relay to be falsely detected as ON. As a result, the Battery ECU may incorrectly determine the relay status, preventing READY mode activation and resulting in a no-start condition. One or more of the following DTCs may be stored: P0AB9, U0100, U0110, and U0115 and multiple warning lights may also turn on. This is caused by corrosion of the connector terminals on the 3002-411 connector in the luggage compartment from water. To eliminate this concern, urethane has been added around the connector to help prevent water from reaching the connector terminals. REPAIR PROCEDURE 1. Verify the customer concern. 2. Diagnose and repair the vehicle according to the following steps. NOTE: The following procedure uses a heat shrink tube with solder. (1) Connect wire to wire with heat shrink tube. (2) Form a loop at the end of wire to create a passage for the other wire.
SA-038-26a2026-09-04. Service bulletin. This Service Alert supersedes the previously issued service alert listed below. The changes are noted in Red text. SA-038/26 06/15/26 DESCRIPTION Some customers may complain about any of the following: 1. Infotainment Center Display does not provide the Authorization Code (OTP) during the MyMazda App Connected Vehicle enrollment. 2. Remote functions inoperative. Engine Start / Stop Door Lock / Unlock Lights ON / OFF Climate Control 3. MAZDA CONNECT connected vehicle reception strength icon shows "X" or " ". Index MAZDA CONNECT 2 Center Display Status Icon MAZDA CONNECT 3 Center Display Status Icon Remote Engine Start Will Not Function Remote Engine Start Function Will turn engine OFF Customer Subscription Status TCU Communication Line Status
SA-058-262026-09-04. Service bulletin. This Service Alert supersedes the previously issued SA(s) listed below. The changes are noted in Red. SA-001/25 10/16/25, 05/15/25, 04/17/25 and 01/09/25 DESCRIPTION This Service Information is no longer valid and has been unpublished. Refer to: MSP66 - ENGINE WARNING ILLUMINATION WITH DTC P0DAB - 2024-2026 CX-90 AND 2025-2026 CX-70
SA-048-262026-09-04. Service bulletin. Some vehicle may exhibit the CHECK ENGINE light on with DTC P0524 (Engine oil pressure control system: Oil pressure decrease) and no abnormal engine noise. This may be caused by a malfunction of the oil pressure control valve (located at the rear of the engine block near the oil filter) due to machining contamination inside the electromagnet sleeve and the solenoid plunger remaining during manufacturing. This contamination is affecting the OCV operation when oil pressure control is requested by the PCM. REPAIR PROCEDURE Perform the WSM inspection for P0524.
09-023-262026-09-02. Service bulletin. DESCRIPTION Some customers may complain that the Adaptive LED Headlights (ALH) aim upward for several seconds just before the vehicle comes to a stop during nighttime driving. This is caused by improper control logic of the ALH. To eliminate this concern, the control software of the ALH has been modified. REPAIR PROCEDURE 1. Verify the customer concern. 2. Reprogram the ALH with the Mazda Modular Diagnostic System (M-MDS), using Mazda Diagnostic And Repair Software (MDARS). Refer to MDARS ECU Reprogramming Procedure.
01-010-262026-09-02. Service bulletin. This bulletin supersedes the previously issued bulletin(s) listed below. The changes are noted in Red text. 01-012/22 10/06/22 DESCRIPTION Some vehicles may exhibit accumulation of dried coolant (1) around the water pipe (2). This is caused by a gap between the housing and pipe due to a press fitting during the manufacturing process. The accumulated coolant is solidified and plugs the gap in high temperature environment and the seepage is stopped and does not progress. This is normal and does not require a part replacement, clean off the dried coolant from around the pipe with a wire brush. REPAIR PROCEDURE 1. Verify the customer concern. 2. If the above condition is experienced, remove the accumulated coolant around the pipe (1) with a wire brush etc. NOTE: Perform the procedure on the vehicle. No need to remove the water pipe and hoses.
SA-042-262026-07-03. Service bulletin. This Service Alert supersedes the previously issued SAs listed below. The changes are noted in Red text. SA-017/25 12/16/25, 09/08/25, 07/14/25, 05/15/25 and 03/21/25 DESCRIPTION Mazda Connect Frequently Asked Questions (FAQ) Index General Questions MAZDA CONNECT Indication Setup and Getting Started Dealer Processes Registration / Enrollment / Take-Over Customer Subscription Status WI-FI General Informatio Opening the TCU Communication Line WI-FI How-To Conditions for Remote Engine Start Will Not Function WI-FI Trial Period Conditions for Remote Engine Start Function Will turn engine OFF Interacting With The App TCU Communication Line Status Service Issues Educational Videos Troubleshooting Resources MyMazda App Error Codes Customer Opt-Out