WenmarOpen by Wenmar Pro

Service bulletin NTB20-085A

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10213681
Published by NHTSA2022-06-08
Manufacturer's numberNTB20-085A
Manufacturer's date2022-04-21
NHTSA componentEQUIPMENT; ELECTRICAL SYSTEM

NHTSA's summary

TELEMATICS CONTROL UNIT RESET AFTER AUTOMATIC COLLISION NOTIFICATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Electrical system, Equipment and accessories

Vehicles listed
NISSAN ARMADA2021, 2022
NISSAN FRONTIER2022
NISSAN KICKS2021, 2022
NISSAN MAXIMA2021, 2022
NISSAN PATHFINDER2022
NISSAN ROGUE2021
NISSAN SENTRA2021, 2022
NISSAN TITAN2020, 2021, 2022
NISSAN TITAN XD2020, 2021, 2022 (the catalog's model; the bulletin names a series or trim of it)
NISSAN redundant ROGUE2022

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
26V4550002026-07-15. EQUIPMENT:OTHER:LABELS
22V5270002022-07-21. EQUIPMENT:ELECTRICAL:INFOTAINMENT:SOFTWARE; BACK OVER PREVENTION: SENSING SYSTEM: CAMERA
20206032020-12-09. Electrical
20V7590002020-12-08. ENGINE; ELECTRICAL SYSTEM:WIRING:FRONT UNDERHOOD

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
NTB23-048A2026-04-29. Service bulletin. DTC P17F4 STORED IN THE TCM IF YOU CONFIRM The customer reports transmission vibration when accelerating, HINT: Vibration occurs during quick reacceleration after braking, during a 2-1 downshift of the auxiliary gearbox. AND DTC P17F4 for “AUXILIARY GEARBOX (CL JUDDER)” is stored in the TCM. · If DTCs other than P17F4 are stored, this bulletin does not apply. Refer to the ESM for further diagnostic information. ACTION Refer to the Repair Overview on page 2 to determine if this bulletin applies. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
NTB25-030A2025-10-21. Service bulletin. STEERING WHEEL SWITCH BUTTONS INOPERATIVE, STICKING, OR NOT CLICKING WHEN PRESSED IF YOU CONFIRM The customer states that any of the steering wheel switch buttons are inoperative, sticking, or not clicking when pressed. ACTION Follow the SERVICE PROCEDURE to: 1. Remove the steering wheel assembly. 2. Replace the switch assembly on the steering wheel assembly. HINT: The switch assembly includes switches for both sides of the steering wheel. 3. Reinstall the steering wheel assembly. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB25-0142025-03-25. Service bulletin. REAR VIEW CAMERA IS INOPERATIVE OR "X" IS DISPLAYED WHEN SHIFTING INTO REVERSE IF YOU CONFIRM The Rear View Camera is inoperative or an "X" is displayed when shifting into reverse, AND There is corrosion at the Rear View Camera wiring harness connector D504 (Figure 2 on page 2). ACTION 1. Replace the Wiper Grommet Seal, the Rear Camera Harness, add Rear Camera Wiring Harness Dampers and, if there are signs of corrosion in the camera connector, the Camera. 2. Add Drain holes to the bottom of the rear door.
NTB19-042F2025-02-25. Service bulletin. AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING APPLIED SYSTEMS: Vehicles equipped with a lane camera (see Figure 1) SERVICE INFORMATION If the Automatic Emergency Braking (AEB) warning light or is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: • When contamination or foreign material adhere to the lane camera viewing window on the windshield. • When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield. • When the lane camera viewing window on the windshield is temporarily fogged up. Figure 1 Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. HINT: o Refer to the applicable ESM for diagnosis if DTCs are present in the Laser/Radar, ICC/ADAS, or Lane Camera systems. o For further information: • Refer to the following pages. • Use the search keyword “blinking” in the ESM.
NTB19-033G2025-02-25. Service bulletin. INTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
NTB25-0072025-02-10. Service bulletin. MIL ON WITH DTC P0196 STORED IN THE ECM IF YOU CONFIRM The MIL is ON with DTC P0196 for “EOT SENSOR” stored in the ECM. HINT: DTC P0012 for “INTAKE VALVE TIMING CONTROL B1” may be stored along with P0196 for “EOT SENSOR”. ACTION Follow the SERVICE PROCEDURE in this bulletin to diagnose DTC P0196 for “EOT SENSOR”. • Disregard P0012 if stored along with P0196. • Do not follow the service information in the ESM when diagnosing P0196. • The ESM information will be updated at a later date.
NTB21-040B2025-01-30. Service bulletin. DTCS B2740-87, B2744-87, AND/OR B274D-87 STORED IF YOU CONFIRM Any of the following DTCs are stored: • B2740-87 (TCU) • B2744-87 (BCM) • B274D-87 (Combination Meter) ACTION Follow the SERVICE PROCEDURE to reprogram the Sonar Control Unit, if applicable. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
NTB20-066C2024-10-22. Service bulletin. LANE CAMERA AIMING VEHICLE REFERENCE VALUES NOT IN ESM SERVICE INFORMATION If the lane camera requires aiming, the values in Table A on page 4 must be used. • For all other models/model years, consult the Electronic Service Manual (ESM).
NTB23-032B2024-09-18. Service bulletin. HVAC BLOWER DOES NOT OPERATE ON COLD STARTS APPLIED VEHICLES: 2021-2023 Rogue (T33) APPLIED DATES: VINs starting with 5N1 – built before November 22, 2022 VINs starting with JN8 – All IF YOU CONFIRM The HVAC blower does not operate during vehicle cold starts, AND The HVAC blower will start to operate when the A/C is toggled OFF and ON. ACTION Follow the SERVICE PROCEDURE to: 1. Confirm the current A/C Amplifier part number. 2. Follow steps 17 and 18 on page 8 to determine if the A/C Amplifier will be replaced, can be reprogrammed, or if this bulletin does not apply. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
NTB24-016A2024-09-04. Service bulletin. DTC P161F FOR IMMOBILIZER CODE STORED IN ECM WITH VEHICLE NO-START CONDITION APPLIED VEHICLES: APPLIED DATES: 2022-2023 Pathfinder (R53) Built on or before October 17, 2022 IF YOU CONFIRM The vehicle cranks but will not start, and DTC P161F for “IMMOBILIZER” is stored in the ECM. ACTION Follow the SERVICE PROCEDURE in this bulletin to reprogram the ECM, if applicable. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.