Service bulletin NTB25-030A

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	11024395
Published by NHTSA	2025-10-21
Manufacturer's number	NTB25-030A
Manufacturer's date	2025-10-01
Campaign id or software version	EL25-001A
NHTSA component	ELECTRICAL SYSTEM

NHTSA's summary

STEERING WHEEL SWITCH BUTTONS INOPERATIVE, STICKING, OR NOT CLICKING WHEN PRESSED IF YOU CONFIRM The customer states that any of the steering wheel switch buttons are inoperative, sticking, or not clicking when pressed. ACTION Follow the SERVICE PROCEDURE to: 1. Remove the steering wheel assembly. 2. Replace the switch assembly on the steering wheel assembly. HINT: The switch assembly includes switches for both sides of the steering wheel. 3. Reinstall the steering wheel assembly. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Electrical system

Vehicles listed
NISSAN PATHFINDER	2022, 2023, 2024, 2025
NISSAN ROGUE	2021, 2022, 2023, 2024, 2025

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
NTB25-046	2025-10-21. Service bulletin. VOLUNTARY SERVICE CAMPAIGN 2025 ROGUE; REMOTE ENGINE START BCM CONFIGURATION INTRODUCTION Nissan is conducting this voluntary service campaign on certain specific model year 2025 Rogue vehicles to reconfigure the BCM. This service will be performed at no charge to the customer for parts or labor. IDENTIFICATION NUMBER Nissan has assigned identification number PD175 to this campaign. This number must appear on all communication and documentation of any nature dealing with this campaign. DEALER RESPONSIBILITY Dealers are to repair vehicles falling within range of this campaign that enter the service department. This includes vehicles purchased from private parties, vehicles presented by transient (tourists) owners, and vehicles in a dealer’s inventory.
NTB25-046	2025-10-21. Service campaign. ***Dealer Announcement* Nissan is conducting a service campaign on certain model year 2025 Nissan Rogue vehicles identified in Service Comm and National Service History – Open Campaigns. On affected vehicles, some NissanConnect Services subscribers are unable to access the remote engine start/stop and climate (RES) features via both the mobile app and the web portal. Customers are still able to use the key fob to remotely start their vehicle. To restore NissanConnect Services subscribers’ RES feature through the mobile app and web portal, your Nissan dealer will reconfigure the Body Control Module (BCM). *What Dealers Should Do*** 1. Verify if vehicles are affected by this service campaign using Service Comm or DBS National Service History – Open Campaigns I.D. PD175 2. If a retailed vehicle affected by this Campaign ID visits the dealer for service, the dealer should inform the customer about the service campaign and communicate the reconfiguration is available. 3. Once remedied, dealers should submit the applicable warranty claim for the action performed so it can be closed in Service Comm and release the vehicle to the customer.
NTB25-014	2025-03-25. Service bulletin. REAR VIEW CAMERA IS INOPERATIVE OR "X" IS DISPLAYED WHEN SHIFTING INTO REVERSE IF YOU CONFIRM The Rear View Camera is inoperative or an "X" is displayed when shifting into reverse, AND There is corrosion at the Rear View Camera wiring harness connector D504 (Figure 2 on page 2). ACTION 1. Replace the Wiper Grommet Seal, the Rear Camera Harness, add Rear Camera Wiring Harness Dampers and, if there are signs of corrosion in the camera connector, the Camera. 2. Add Drain holes to the bottom of the rear door.
NTB19-042F	2025-02-25. Service bulletin. AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING APPLIED SYSTEMS: Vehicles equipped with a lane camera (see Figure 1) SERVICE INFORMATION If the Automatic Emergency Braking (AEB) warning light or is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: • When contamination or foreign material adhere to the lane camera viewing window on the windshield. • When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield. • When the lane camera viewing window on the windshield is temporarily fogged up. Figure 1 Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. HINT: o Refer to the applicable ESM for diagnosis if DTCs are present in the Laser/Radar, ICC/ADAS, or Lane Camera systems. o For further information: • Refer to the following pages. • Use the search keyword “blinking” in the ESM.
NTB19-033G	2025-02-25. Service bulletin. INTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
NTB25-007	2025-02-10. Service bulletin. MIL ON WITH DTC P0196 STORED IN THE ECM IF YOU CONFIRM The MIL is ON with DTC P0196 for “EOT SENSOR” stored in the ECM. HINT: DTC P0012 for “INTAKE VALVE TIMING CONTROL B1” may be stored along with P0196 for “EOT SENSOR”. ACTION Follow the SERVICE PROCEDURE in this bulletin to diagnose DTC P0196 for “EOT SENSOR”. • Disregard P0012 if stored along with P0196. • Do not follow the service information in the ESM when diagnosing P0196. • The ESM information will be updated at a later date.
NTB25-002	2025-01-30. Service bulletin. INTELLIGENT AROUND VIEW MONITOR CAMERA CALIBRATION SERVICE INFORMATION If any Around View Monitor (AVM) camera (front, sides, or rear) and/or the AVM Control Module is replaced, camera calibration is required. The SERVICE PROCEDURE in this bulletin can be used in conjunction with the ESM and CONSULT 4 procedures for additional clarification when performing AVM camera calibration. • Refer to the ESM: DRIVER INFORMATION & MULTIMEDIA > AUDIO, VISUAL & NAVIGATION SYSTEM > INTELLIGENT AROUND VIEW MONITOR > BASIC INSPECTION > CALIBRATING CAMERA IMAGE (INTELLIGENT AROUND VIEW MONITOR) > WITH ProPILOT ASSIST 2.1
NTB21-040B	2025-01-30. Service bulletin. DTCS B2740-87, B2744-87, AND/OR B274D-87 STORED IF YOU CONFIRM Any of the following DTCs are stored: • B2740-87 (TCU) • B2744-87 (BCM) • B274D-87 (Combination Meter) ACTION Follow the SERVICE PROCEDURE to reprogram the Sonar Control Unit, if applicable. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
NTB23-032B	2024-09-18. Service bulletin. HVAC BLOWER DOES NOT OPERATE ON COLD STARTS APPLIED VEHICLES: 2021-2023 Rogue (T33) APPLIED DATES: VINs starting with 5N1 – built before November 22, 2022 VINs starting with JN8 – All IF YOU CONFIRM The HVAC blower does not operate during vehicle cold starts, AND The HVAC blower will start to operate when the A/C is toggled OFF and ON. ACTION Follow the SERVICE PROCEDURE to: 1. Confirm the current A/C Amplifier part number. 2. Follow steps 17 and 18 on page 8 to determine if the A/C Amplifier will be replaced, can be reprogrammed, or if this bulletin does not apply. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.
NTB24-016A	2024-09-04. Service bulletin. DTC P161F FOR IMMOBILIZER CODE STORED IN ECM WITH VEHICLE NO-START CONDITION APPLIED VEHICLES: APPLIED DATES: 2022-2023 Pathfinder (R53) Built on or before October 17, 2022 IF YOU CONFIRM The vehicle cranks but will not start, and DTC P161F for “IMMOBILIZER” is stored in the ECM. ACTION Follow the SERVICE PROCEDURE in this bulletin to reprogram the ECM, if applicable. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.