Service bulletin NTB21-081B

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10208962
Published by NHTSA	2022-03-12
Manufacturer's number	NTB21-081B
Manufacturer's date	2022-02-14
NHTSA component	ELECTRICAL SYSTEM; STRUCTURE:BODY:DOOR

NHTSA's summary

AUTOMATIC BACK DOOR INOPERATIVE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Body and frame, Electrical system

Vehicles listed
NISSAN PATHFINDER	2022
NISSAN ROGUE	2021
NISSAN redundant ROGUE	2022

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
2021557	2021-09-13. Structure

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
ITB09-063C	2026-04-29. Service bulletin. CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Infiniti by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB09-131C	2026-04-29. Service bulletin. CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB09-131C	2026-04-29. Service bulletin. CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB25-030A	2025-10-21. Service bulletin. STEERING WHEEL SWITCH BUTTONS INOPERATIVE, STICKING, OR NOT CLICKING WHEN PRESSED IF YOU CONFIRM The customer states that any of the steering wheel switch buttons are inoperative, sticking, or not clicking when pressed. ACTION Follow the SERVICE PROCEDURE to: 1. Remove the steering wheel assembly. 2. Replace the switch assembly on the steering wheel assembly. HINT: The switch assembly includes switches for both sides of the steering wheel. 3. Reinstall the steering wheel assembly. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB25-029	2025-06-04. Service bulletin. EXCESS DUST ENTERING CABIN WHILE DRIVING ON DIRT ROADS IF YOU CONFIRM That while driving on dirt roads with all doors and windows closed, that there is excessive dust intrusion into the vehicle’s cabin that is settling on the inside of the doors. ACTION Refer to the SERVICE PROCEDURE in the bulletin to: 1. Install Butyl Patches around the door seals of driver (LH) side and passenger (RH) side front and rear doors. 2. Install drain plugs into door drains of driver (LH) side and passenger (RH) side front and rear doors.
NTB25-014	2025-03-25. Service bulletin. REAR VIEW CAMERA IS INOPERATIVE OR "X" IS DISPLAYED WHEN SHIFTING INTO REVERSE IF YOU CONFIRM The Rear View Camera is inoperative or an "X" is displayed when shifting into reverse, AND There is corrosion at the Rear View Camera wiring harness connector D504 (Figure 2 on page 2). ACTION 1. Replace the Wiper Grommet Seal, the Rear Camera Harness, add Rear Camera Wiring Harness Dampers and, if there are signs of corrosion in the camera connector, the Camera. 2. Add Drain holes to the bottom of the rear door.
NTB19-042F	2025-02-25. Service bulletin. AUTOMATIC EMERGENCY BRAKING WARNING LIGHT BLINKING APPLIED SYSTEMS: Vehicles equipped with a lane camera (see Figure 1) SERVICE INFORMATION If the Automatic Emergency Braking (AEB) warning light or is blinking (but not illuminated steadily) or the customer states it is blinking, and there are no related DTCs, inspect the windshield. A blinking AEB warning light may occur under the following conditions: • When contamination or foreign material adhere to the lane camera viewing window on the windshield. • When driving while it is snowing or when frost forms on the lane camera viewing window on the windshield. • When the lane camera viewing window on the windshield is temporarily fogged up. Figure 1 Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. HINT: o Refer to the applicable ESM for diagnosis if DTCs are present in the Laser/Radar, ICC/ADAS, or Lane Camera systems. o For further information: • Refer to the following pages. • Use the search keyword “blinking” in the ESM.
NTB19-033G	2025-02-25. Service bulletin. INTELLIGENT CRUISE CONTROL INOPERATIVE AND AEB/FEB WARNING LIGHT ON OR RADAR OBSTRUCTION MESSAGE DISPLAYED WITH DTC C1A16 OR C2582 IF YOU CONFIRM IMPORTANT: The purpose of ACTION (on the next page) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair. Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle. The customer states that the ICC stopped working while driving, OR The customer states that the AEB/FEB warning light is ON, or turned ON, while driving (Figure 1), OR The message “Unavailable Front Radar Obstruction” or “Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner's Manual” has displayed while driving (Figure 2). AND DTC C1A16, C1A16-97, C2582, or C2582-97 is the ONLY DTC stored. Figure 1 Figure 2 This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. Forward Driving Aids Temporarily Disabled Front Sensor Blocked See Owner’s Manual
NTB25-007	2025-02-10. Service bulletin. MIL ON WITH DTC P0196 STORED IN THE ECM IF YOU CONFIRM The MIL is ON with DTC P0196 for “EOT SENSOR” stored in the ECM. HINT: DTC P0012 for “INTAKE VALVE TIMING CONTROL B1” may be stored along with P0196 for “EOT SENSOR”. ACTION Follow the SERVICE PROCEDURE in this bulletin to diagnose DTC P0196 for “EOT SENSOR”. • Disregard P0012 if stored along with P0196. • Do not follow the service information in the ESM when diagnosing P0196. • The ESM information will be updated at a later date.
NTB21-040B	2025-01-30. Service bulletin. DTCS B2740-87, B2744-87, AND/OR B274D-87 STORED IF YOU CONFIRM Any of the following DTCs are stored: • B2740-87 (TCU) • B2744-87 (BCM) • B274D-87 (Combination Meter) ACTION Follow the SERVICE PROCEDURE to reprogram the Sonar Control Unit, if applicable. IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it contains information that is essential to successfully completing this repair.