Service bulletin LI82.85-P-072218
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10188420 |
| Published by NHTSA | 2021-03-08 |
| Manufacturer's number | LI82.85-P-072218 |
| Manufacturer's date | 2021-01-04 |
| NHTSA component | EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); ELECTRICAL SYSTEM |
NHTSA's summary
The "Commuter route" option is activated in the settings of the MBUX multimedia system (A26/17). Therefore, the navigation system automatically detects that the vehicle is on a commuter route and automatically starts route guidance without any voice output.
The document
The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.
Components
Electrical system, Equipment and accessories
| MERCEDES BENZ SPRINTER 2500 | 2013, 2014, 2015 (the catalog's model; the bulletin names a series or trim of it) |
|---|---|
| MERCEDES BENZ SPRINTER 3500 | 2013 (the catalog's model; the bulletin names a series or trim of it) |
| MERCEDES BENZ SPRINTER 3500 | 2015 (the catalog's model; the bulletin names a series or trim of it) |
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| 2021050 | 2021-02-05. Electrical |
|---|---|
| 17V786000 | 2017-12-08. EQUIPMENT |
| 2017247 | 2017-05-10. Electrical |
| 16V093000 | 2016-02-18. EQUIPMENT:OTHER:LABELS |
| 14V706000 | 2014-11-05. EQUIPMENT ADAPTIVE/MOBILITY |
A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.
| PartsC | 2023-05-08. Service bulletin. recall campaign announcement. |
|---|---|
| 2017030016 | 2023-05-08. Service bulletin. Recall Campaign bulletin |
| LI00.19-N-075749 | 2023-02-03. Service bulletin. Complaint Various issues including control unit programming procedure will not complete successfully/no newer software found, communication faults, or sporadic malfunction of systems. Cause Aftermarket CAN device could be installed into the vehicle's CAN network. Such devices can be but are not limited to, remote start modules, CAN blockers, or high idle modules. Remedy A successful control unit programming session cannot be ensured while aftermarket devices are connected to the vehicle's CAN network. Some of the device companies supply a bypass to allow control unit programming. |
| LI07.16-N-075574 | 2023-01-05. Service bulletin. Problem: Vehicle fails smog test Cause In the event the Engine Control Module (CDI) detects a fault with the Water Pump Short Circuit to Battery diagnostic, Fault Code P260312 and/or P260315 may set and prevent the readiness monitor from running. Even following a successful repair and/or clearing the Fault Code(s), the readiness monitor remains deactivated and self-healing is not possible. This deactivation may prevent the vehicle from passing state emissions inspection and SMOG Test and is only resolvable by installing new engine control unit software. Remedy 1. Perform XENTRY Quick Test. 2. Check for the presence of Fault Code P260312 and/or P260315 in the CDI control module. 3. If relevant Fault Codes are present, resolve fault using standard dealer procedures. Once fault is resolved, proceed to step 5. 4. If no relevant Fault Codes are present, or the fault has been previously repaired and Fault Codes erased, proceed to step 5. |
| LI01.00-N-074210 | 2022-02-04. Service bulletin. Complaint Oil loss from engine or visible traces of oil in the engine compartment. Cause To be determined in each possible situation Remedy Procedure for cause analysis: 1. Clean the engine if necessary. 2. Apply leak tracing powder. 3. Perform a test drive. 4. Locate the oil leak. 5. Perform the repair in accordance with the specific WIS document appropriate for the cause of the oil leak. |
| LI54.22-N-074063 | 2022-01-06. Service bulletin. Various complaints due to aftermarket OBDII device installed |
| LI00.30-N-074118 | 2022-01-06. Service bulletin. "The “monitor status this driving cycle (PID 41)” can be displayed as “disabled” in the generic scan tool although no monitor of this group is disabled " |
| Launch NCU-VSXHE | 2021-03-15. Service bulletin. "eCall" Hermes Software Update |
| 2017030004 | 2021-03-01. Service bulletin. Replace 3rd brake lamp, remove soft top compartment cover to access. |
| Launch NCU - 202 | 2021-03-01. Service bulletin. Mercedes-Benz AG (?MBAG?), the manufacturer of Mercedes-Benz, has determined that on certain Model Year (?MY?) 2013-2017 B-Class, C-Class, CLA-Class, CLS-Class, E-Class, G-Class, GL-Class, GLA-Class, GLC-Class, GLE-Class, GLK-Class, GLS-Class, GT-Class, M-Class, S-Class, SL-Class, and SLK-Class (117, 156, 166, 172, 190, 204, 205, 207, 212, 217, 218, 222, 231, 242, 253, 292, and 463 platform), the software for the PASS control unit does not meet current series production configuration and therefore the possibility exists that a correct GPS position cannot be determined in the control unit for location based services, and an incorrect vehicle position may be displayed. Please note the E-call feature is not impacted by this issue. What We?re Doing MBUSA will conduct a Service Campaign. An authorized Mercedes-Benz dealer will update the PASS Control Unit Software |