WenmarOpen by Wenmar Pro

Service bulletin SA-037-17

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
TypeService bulletin
NHTSA id10186323
Published by NHTSA2021-02-01
Manufacturer's numberSA-037-17
Manufacturer's date2017-02-27
NHTSA componentEQUIPMENT

NHTSA's summary

RECALL 0516J UPDATED REPAIR PROCEDURE

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Equipment and accessories

Vehicles listed
MAZDA CX-32017
MAZDA CX-52017
MAZDA CX-92017
MAZDA MAZDA22017
MAZDA MAZDA32017
MAZDA MAZDA52017
MAZDA MAZDA62017
MAZDA MX-52017
MAZDA RX-82017

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
SA-027-242024-05-04. Service bulletin. Some customers may complain about infotainment center display. Peeling, spider cracks and white dots.
SA-008-242024-03-06. Service bulletin. Use the symptom troubleshooting tables below to diagnose MAZDA CONNECT concerns.
09-003-23b2024-01-06. Service bulletin. Some customers may complain about infotainment center display: Center display touchscreen operates by itself (Ghost Touch). The film of the center display may be peeled off. White dots may appear on the center display NOTE: The occurrence of the symptoms depends on the vehicle model and the parts.
SA-032-23a2023-11-02. Service bulletin. If you encounter any type of electrical concern (e.g, dead battery, engine no start, DTC(s) stored...), interview the customer before proceeding with normal MGSS diagnosis by asking if any aftermarket devices have been installed. Aftermarket devices may be the cause of the electrical concern. Below are a few examples of unusual electrical concerns caused by aftermarket devices.
09-032-232023-10-05. Service bulletin. SERVICE BULLETIN 09-031/20 ISSUED ON 09/21/20 IS NO LONGER VALID. IT IS SUPERCEDED BY RECALL 6023G (“2014-2018 MAZDA3 AND 2016-2021 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY”).
09-031-20b2023-08-04. Service bulletin. Some vehicles may exhibit a distorted image or no image from the rear mount camera when shifted into reverse. Due to friction, the coating of camera socket terminals may wear out, creating high electrical resistance. NOTE: The icons and the messages are displayed normally.
09-031/20a2023-08-04. Service bulletin. Be advised that TSB "09-031/20 - REAR MOUNT CAMERA IMAGE NOT CLEAR/NO IMAGE ON SCREEN" is no longer valid and has been superseded by "RECALL 6023G - 2014-2018 MAZDA3 AND 2016-2019 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY". Use the link below to view the recall: RECALL 6023G - 2014-2018 MAZDA3 AND 2016-2019 CX-3 - REARVIEW IMAGE MAY NOT DISPLAY PROPERLY
09-028-232023-08-03. Service bulletin. Some CX-5 and CX-30 customers may find that the liftgate does not close when pressing the power liftgate (PLG) rear switch (A) located on the interior liftgate trim. This may be caused by PLG switch corrosion. Water from a high pressure car washer and/or condensation may drip onto the switch connector and cause corrosion. To eliminate this concern, the PLG rear switch has been modified with a waterproof connector.
SA-036-232023-07-05. Service bulletin. Interior parts made of resin have antistatic coating to prevent dust from sticking on the surfaces, and depending on the conditions of use, the antistatic components may crystallize slightly, giving an appearance of white stains on the surface. To remove the stains, wipe the stained surface with a towel soaked with water mixed with a small portion of a neutral detergent. If the white stains reappear again, simply wipe them again in the same way. NOTE: The antistatic effect does not deteriorate with this procedure.
SA-016-232023-04-04. Service bulletin. There are currently 2 methods for cutting a new auxiliary key blank. A. Auxiliary Key Trace Cut Method. B. Auxiliary Key Code Cut Method