Service bulletin TSB 19-2090

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10156524
Published by NHTSA	2019-04-02
Manufacturer's number	TSB 19-2090
Manufacturer's date	2019-03-25
NHTSA component	POWER TRAIN

NHTSA's summary

Some 2015-2019 Mustang GT350/GT350R vehicles may exhibit a hesitation or surge in the vehicle with no diagnostic trouble codes (DTCs) present. This may be accompanied by an inoperative cruise control system. This may be due to a transmission output shaft flange nut that has become loose, allowing the output shaft tone ring to move in relation to the output shaft causing an erroneous signal. To resolve the condition, replace the output shaft flange.

The document

The document is the manufacturer's. This site does not hold it. NHTSA files a document at one of these two addresses; we have not asked NHTSA which.

Components

Transmission and driveline

Vehicles listed
FORD MUSTANG	2015, 2016, 2017, 2018, 2019

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Recalls for the same vehicles and component
2025707	2025-12-18. Powertrain
22V382000	2022-05-27. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM)
2020203	2020-05-11. Powertrain
20V263000	2020-05-08. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL; POWER TRAIN:AUTOMATIC TRANSMISSION:GEAR POSITION INDICATION (PRNDL)
2018164	2018-04-05. Powertrain
18V213000	2018-04-04. POWER TRAIN:AUTOMATIC TRANSMISSION

A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.

Other bulletins for the same vehicles and component
SSM 54366	2025-11-19. Service bulletin. Some 2015-2021 Ford and Lincoln vehicles may exhibit an illuminated MIL with diagnostic trouble codes (DTCs) P0011, P0012, P0014, P0015, P0016, P0017, P0018, P0019, P0021, P0022, P0024 and/or P0025. Pinpoint test HK in the Powertrain Control and Emissions Diagnosis (PC/ED) or in Section 303-14 of the Workshop Manual (WSM) has been updated to address this concern.
TSB 25-2475	2025-11-04. Service bulletin. This bulletin supersedes TSB 25-2301. Reason for update: update the Part List Description. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh engagement * Delayed engagement * Harsh shift * Delayed shift * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to axial movement of the CDF clutch cylinder (7H351) sleeve causing hydraulic circuit leaks. NOTE: If internal transmission service is required to address a concern detected with the CDF clutch cylinder following this article, technicians should carefully inspect and replace other transmission components and flush transmission fluid cooler only as necessary as needed to ensure proper function. Add a new line to the repair order to document any additional
TSB 25-2301	2025-08-19. Service bulletin. This bulletin supersedes TSB 25-2126. Reason for update: update the Part List and Service Procedure. Some of the vehicles listed in the Model statement above may exhibit at least one of the following conditions: * Harsh engagement * Delayed engagement * Harsh shift * Delayed shift * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to axial movement of the CDF clutch cylinder (7H351) sleeve causing hydraulic circuit leaks. NOTE: If internal transmission service is required to address a concern detected with the CDF clutch cylinder following this article, technicians should carefully inspect and replace other transmission components and flush transmission fluid cooler only as necessary as needed to ensure proper function. Add a new line to the repair order to documen
SSM 52586	2024-06-10. Service bulletin. Some 2018-2023 Mustang vehicles equipped with a 5.0L engine and a 10R80 transmission may exhibit a buck/jerk sensation that may be perceived as an engine misfire during throttle tip-in between 35-45 mph (56-72 km/h) and with the transmission in 8th, 9th, or 10th gear. This buck/jerk sensation is a characteristic of the vehicle and can be compared to a like vehicle that is equipped with a similar powertrain (engine, transmission, and rear end gear ratio) driven in the same manner. A diagnostic trouble code (DTC) will not set because of this condition. If no DTC is set, inform the customer that the vehicle is operating as designed. If a misfire DTC is present, the DTC should be diagnosed first following the correct diagnostic procedure outlined in the Workshop Manual, Section 303-07B.
SSM 52548	2024-05-23. Service bulletin. Various vehicles equiped with 10R80/10R80 MHT/10R100/10R140 transmissions may require replacement of the seal kits (7153) when internal repairs are being performed. These kits come with 4 wheel drive (4WD) seals and will no longer include the 2WD seals. When working on a 2WD vehicle, any 2WD seals must be ordered separately. Refer to the parts catalog for the proper 2WD seals required.
SSM 52444	2024-04-29. Service bulletin. Some 2018-2024 Mustang vehicles built on and after 04-Dec-2017 may exhibit a ting, pop, clunk, or click noise from the rear wheel hub when accelerating, applying brakes, or when shifting between drive/reverse (torque reversals). This condition may be caused by stick/slip between the hub and halfshaft interface during the torque reversals creating the ting, pop, clunk, or click noise. To correct the condition, refer to the Workshop Manual (WSM) to replace the halfshaft and hub assembly of the suspected side(s).
SSM 52428	2024-04-29. Service bulletin. Some 2018-2024 Mustang vehicles built on 04-Dec-2017 and through 01-Oct-2023 may exhibit a ting, pop, clunk, or click noise from the rear wheel hub when accelerating, applying brakes, or when shifting between drive/reverse (torque reversals). This condition may be caused by stick/slip between the hub and halfshaft interface during the torque reversals creating the ting, pop, clunk, or click noise. To correct the condition, refer to the Workshop Manual (WSM) to replace the halfshaft and hub assembly of the suspected side.
TSB 24-2101	2024-04-04. Service bulletin. This article supersedes TSB 24-2046 to update the Service Procedure LTIS statement. Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang, 2019-2023 Ranger vehicles equipped with a 10R80 transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) that are stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.
SSM 52314	2024-03-20. Service bulletin. During service and repair requiring removal and replacement of a crankshaft bolt and/or crankshaft damper, achieving proper torque of the crankshaft pulley bolt is critical. Incorrect torque may allow the bolt to loosen resulting in the timing gear breaking and engine damage. Replacement of the bolt is critical to the repair and accurately following the installation procedure in the Workshop Manual (WSM) Section, 303-01 is extremely important. The bolt torque procedure can be found in the crankshaft front seal removal and installation procedure or in the engine assembly procedure.
TSB 24-2046	2024-03-07. Service bulletin. This article supersedes TSB 23-2350 to update the Issue statement and the Service Procedure. Some 2017-2020 F-150, 2018-2021 Expedition/Navigator/Mustang, 2019-2023 Ranger vehicles equipped with a 10R80 transmission may exhibit a harsh/delayed engagement and/or harsh/delayed shift, an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0751, P0752, P0756, P0757, P0761, P0762, P0766, P0767, P0771, P0772, P2700, P2701, P2702, P2703, P2704, P2705, P2707, P2708, P0729, P0731, P0732, P0733, P0734, P0735, P0736, P076F, P07D9, P07F6 and/or P07F7 stored in the powertrain control module (PCM) or transmission control module (TCM). This may be due to the transmission solenoid ID strategy, sticking valves in the main control valve body and/or axial movement of the CDF clutch cylinder (7H351) sleeve.