Service bulletin ITB-15-006

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10057378
Published by NHTSA	2015-05-22
Manufacturer's number	ITB-15-006
Manufacturer's date	2015-01-28
NHTSA component	STRUCTURE:BODY

NHTSA's summary

INFINITI: UNDER PASSENGER SIDE A PILLAR, BULKHEAD SEAM IS NOT COMPLETELY SEALED DURING PRODUCTION. MODEL 2015 QX60. *PE

The document

No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.

Components

Body and frame

Vehicles listed
INFINITI Q60	2015

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
ITB09-063C	2026-04-29. Service bulletin. CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Infiniti by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
ITB13-007H	2023-03-07. Service bulletin. REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB09-039J	2023-03-07. Service bulletin. WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
ITB13058A	2021-05-10. Service bulletin. IF YOU CONFIRM: There is a squeak, rattle, buzz, or rubbing type noise coming from the retractable hard top and/or trunk area while driving. - See page 2 and 3 for specific locations and types of noises. ACTION: Refer to the Repair Overview on page 2 and 3. See this bulletin for further detail.
ITB15019	2021-05-10. Service bulletin. SERVICE INFORMATION The Body Control Module (BCM) for the Applied Vehicles in this bulletin is now shipped as a blank unit. As with previous BCM replacements, when a blank unit is installed, the configuration process must be performed. See this bulletin for further detail.
ITB14030	2021-05-10. Service bulletin. SERVICE INFORMATION If the battery becomes disconnected or discharged while the retractable hard top is in any position other than fully closed or fully retracted, the retractable hard top control may stop operating and the following DTCs will be stored: B1707 and B1708. Other retractable hard top related DTCs may also be found stored. To restore operation: (1) close the roof fully manually; (2) erase the DTC(s); and (3) perform hard top control unit initialization. This bulletin provides the procedures to restore retractable hard top control operation. See this bulletin for further detail.
ITB18-037	2018-12-03. Service bulletin. PLASTIC INTERIOR TRIM PROTECTIVE COVERING REMOVAL SERVICE INFORMATION Vehicles are delivered with plastic interior trim protective covering on the front and rear seats, front and rear door panel finishers, steering wheel, and sun visors (see examples on page 2). When removing the protective covering, care must be used to avoid scuffs, scrapes, cuts, and other abrasive contact to interior trim components. DO NOT use sharp objects like razor blades, box cutters, knives, etc. when removing the plastic interior trim protective covering. IMPORTANT: All soft trim described in this bulletin is on automatic return to NNA. Any trim found damaged in the way described in this bulletin will be charged back to the dealer.
ITB16-042	2017-10-25. Service bulletin. 2014-2015 Q60; POWER WINDOWS DO NOT OPERATE CORRECTLY SERVICE INFORMATION If power is interrupted to the power window system, it may cause one or more of the following symptoms to occur on one or both power windows: - AUTO-UP does not work, but window will move up and down with manual operation of the switch. - When door is opened, window will lower a small amount (normal operation) but will not raise when door is closed. - Window will move down when operating the window switch, but will not move up. NOTE: - If any of the above symptoms should occur, it may indicate that Window Initialization is needed (see page 2). Initialization should be done before attempting any repairs. - If needed, refer to the applicable Electronic Service Manual (ESM) to perform electrical diagnosis. - After electrical repairs to the vehicle (including repairs to the power windows), make sure to perform the Window Initialization and Anti-pinch Function Check procedures on page 2.