Service bulletin 08-030

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

The communication, as NHTSA indexes it (as of 2026-10-19)
Type	Service bulletin
NHTSA id	10024874
Published by NHTSA	2008-06-03
Manufacturer's number	08-030
Manufacturer's date	2008-04-10
NHTSA component	ENGINE AND ENGINE COOLING:ENGINE:GASOLINE

NHTSA's summary

2008 (LX/LE) SRT8 - SUSPECT CAM SENSOR THAT MAY SET A MIL FOR P0340 AND/OR P0344. *NJ

The document

No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.

Components

Engine

Trouble codes named

P0340, P0344

Vehicles listed
CHRYSLER 300	2008
DODGE CHARGER	2008
DODGE MAGNUM	2008

Listing a model year does not mean every vehicle of it is concerned: the document says which.

Other bulletins for the same vehicles and component
9003215	2023-01-09. Service bulletin. Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
68332810	2022-10-17. Service bulletin. Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar® Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 N·m [21 ft. lbs.].
9003215	2022-10-17. Service bulletin. Part Description: 5.7L Long Block Issue Description: This 5.7L Long Block Assembly is compatible with both EGR and Non-EGR applications. An EGR Block-Off Plate (53032739AA) must be ordered when installing this Long Block Assembly in a Non-EGR application. Unless, the EGR Block-Off Plate is being transferred from the old engine.
9002887	2022-10-17. Service bulletin. Part Description: Valve Body Assembly Issue Description: Valve body design was changed between 2010MY and 2011MY applications. To prevent mix matching valve bodies and solenoid packs the connectors are color coded.~ Valve bodies with a white connector can be used on 2010, 2009, 2008..., model years. Valve bodies with a gray connector can only be used on 2011, 2012, 2013..., model years.~ Solenoid packs with a white connector are used with 2010, 2009, 2008..., model years. Solenoid packs with a gray connector are used with 2011, 2012, 2013..., model years.
R2118796A	2021-05-03. Service bulletin. Valve Body. These may cause over drive cycling.
18-021-13	2021-03-15. Service bulletin. Flash: Performance Derate Above 55 MPH Immediately After Start-Up When Accelerating At Wide Open Throttle This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. A small number of customers may experience any of the following conditions: Performance derate above 55 MPH when accelerating at wide open throttle immediately following engine start-up.
S1121000006 Rev.	2020-09-28. Service bulletin. (Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns
09-001-13	2018-06-11. Service bulletin. Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
09-001-13	2018-06-04. Service bulletin. Gasoline Engine Diagnostic Inspection Procedure This bulletin provides a procedure to determine repair versus replacement of a gasoline long block engine assembly. This procedure is to be used prior to conducting any engine related repairs or removal of engine components.
9001645	2018-05-21. Service bulletin. Part Description: Short Runner Valve (Actuator) Issue Description: Issue 1~ JC,JS '08-09MY 3.5L only~ Caution - Do not replace the intake manifold for a short runner valve (SRV) fault (P1004 / P2008 / P2016 / P2017) or for a manifold tuning valve (MTV) fault (P1005 / P2077 / P2078). Instead follow the service procedure to investigate P codes associated with diagnosis of the SRV or MTV, then cycle the actuator using a diagnostic tool and verify that the PWM output is 50 (+ 2%) de-energized and 80 (+ 2 %) energized. If no problems observed, then idle the vehicle and verify the correct PWM output (50 + 2% PWM). Replace the actuator if you do not get the desired output. Issue 2~ If the SRV actuator or intake manifold is being replaced for a P1004 Short Runner Valve Performance fault code and the vehicle was built prior to 2/5/07 , technicians must complete the module reflash and verification test per TSB 18-003-07 REV. A to ensure the parts need to be replaced. Please reference TSB 18-003-07 REV. A for specific details on the procedure.