Service bulletin 0300105
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
| Type | Service bulletin |
|---|---|
| NHTSA id | 10012330 |
| Published by NHTSA | 2005-02-24 |
| Manufacturer's number | 0300105 |
| Manufacturer's date | 2005-01-13 |
| NHTSA component | POWER TRAIN:DRIVELINE |
NHTSA's summary
OFF ROADING 4WD LOW RANGE AXLE LOCKERS MAY UNLOCK WHEN IGNITION KEY IS CYCLED. *EH
The document
No address for NHTSA's copy can be built for this communication. Ask the dealer for it by the manufacturer's number.
Components
Transmission and driveline
| JEEP WRANGLER | 2005 |
|---|
Listing a model year does not mean every vehicle of it is concerned: the document says which.
| 05V460000 | 2005-10-06. POWER TRAIN:AUTOMATIC TRANSMISSION |
|---|
A recall listed here may apply to some of the same vehicles. Only the manufacturer can say whether it applies to one vehicle.
| 101232 | 2024-11-07. Service bulletin. Plate - Planetary |
|---|---|
| 9004009 | 2022-09-26. Service bulletin. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. |
| 9004009 | 2022-09-26. Service bulletin. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. |
| 18-042-14 | 2022-08-15. Service bulletin. Generic Powertrain Control Module (PCM) Procedure This bulletin involves programming a generic PCM with software. |
| 18-042-14 | 2018-06-18. Service bulletin. Generic Powertrain Control Module (PCM) Procedure This bulletin involves programming a generic PCM with software. |
| 1802907 | 2007-06-15. Service bulletin. GENERIC POWERTRAIN CONTROL MODULE (PCM) PROCEDURE. *KB |
| 2100206 | 2007-02-01. Service bulletin. FLASH 42RLE - IMPROVED HILL CLIMB CAPABILITY IN REVERSE OR DIAGNOSTIC TROUBLE CODES (DTC) P1713/P1776. *KB |
| 2101705 | 2006-03-24. Service bulletin. FLASH: 42RLE - IMPROVED HILL CLIMB CAPABILITY IN REVERSE OR DTC'S P1713 / P1776. *TT |
| 2101305 | 2005-09-24. Service bulletin. CORRECT SHIFT TOWER SEALER APPLICATION TO PREVENT RESTRICTION OF VENT. *TT |
| 0801505 | 2005-04-26. Service bulletin. POWERTRAIN CONTROL MODULE INITIALIZATION. *SC |