Transport Canada recall 2026258
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | Transport Canada (Canada) |
|---|---|
| Campaign number | 2026258 |
| Manufacturer's number | 26S35 |
| Reported | 2026-05-27 |
| Component | Engine |
| Notification type | Safety Mfr |
| Units potentially affected | 159 |
What is wrong
Issue:
On certain vehicles, the engine may not have been manufactured properly. As a result, the engine could fail and cause a loss of power to the wheels.
Note: This recall only affects certain vehicles equipped with a 2.3 L engine.
Safety Risk:
A sudden loss of power to the wheels could increase the risk of a crash.
Corrective Actions:
Ford will notify owners by mail and advise you to take your vehicle to a dealership to replace the engine.
| 2025 FORD BRONCO | |
|---|---|
| 2026 FORD BRONCO | |
| 2025 FORD EXPLORER | |
| 2026 FORD EXPLORER | |
| 2025 FORD RANGER | |
| 2026 FORD RANGER |
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| SSM 55228 | 2026-10-12. Service bulletin. Some 2020-2026 Aviator/Explorer/F-150/Bronco/Ranger vehicles equipped with a 2.7L or 3.0L (non-diesel) engine may need the front engine cover removed and reinstalled for various reasons. The Workshop Manual (WSM), Section 303-01 Engine > Removal and Installation > Engine Front Cover service procedure has been updated to include a new essential special service tool (ESST) guide pin alignment tool (303-1790) that is used to align the engine front cover to the engine block, preventing the O-ring seal on the engine oil galley feed tube from getting damaged during installation. |
|---|---|
| TSB 26-2372 | 2026-08-21. Service bulletin. This bulletin supersedes 26-2301. Reason for update: to update the Pinpoint Tests referenced in Step 1. Some of the vehicles listed in the Model statement above may require the replacement of the ambient air temperature sensor for various concerns. DTCs P0071, P0072, and/or P0073 may be present in the powertrain control module (PCM). |
| TSB 26-2349 | 2026-08-03. Service bulletin. This bulletin supersedes 25-2415. Reason for update: To add production build dates of the right-side engine valve cover. Some of the vehicles listed in the Model statement above may exhibit oil consumption and blue smoke from the tailpipe. This may be due to the sealing process of the positive crankcase ventilation (PCV) baffle which is part of the valve cover assembly. |
| TSB 26-2269 | 2026-07-13. Service bulletin. Some of the vehicles listed in the Model statement above may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTCs) P0300 and/or P0316 stored in the powertrain control module (PCM) (with no other relevant DTCs present) during a cold start after a 3 to 8 hours cold soak. This may be due to the machining surface of the intake ports in the cylinder head. |
| TSB 26-2210 | 2026-06-05. Service bulletin. Some of the vehicles listed in the Model statement above may exhibit all of the following conditions: * Engine misfire condition * Illuminated malfunction indicator lamp (MIL) with diagnostic trouble codes (DTC) P0301, P0302, P0303, and/or P0304 stored in the powertrain control module (PCM) |
| SSM 54795 | 2026-05-08. Service bulletin. Some 2021-2023 F-150 vehicles equipped with a 3.5L PowerBoost engine and 2020-2026 Explorer vehicles equipped with a 3.3L hybrid engine may exhibit an illuminated powertrain malfunction (wrench) indicator with diagnostic trouble code (DTC) P0A1E stored in the powertrain control module (PCM). The vehicle may be unable to enter electric-only drive modes as expected during normal drive cycles. This may be due to the software within the belt integrated starter generator (BISG). For vehicles with this condition, follow Pinpoint Test I: Battery Isolation/Voltage Stabilization Control Circuit Carry Outance located in the Workshop Manual (WSM), Section 303-06D and repair the vehicle as necessary. Note that the BISG is on backorder status at the time of this publication and Ford is working to make parts available. Engineering is investigating this concern. Monitor PTS for updates. |
| SSM 54774 | 2026-04-28. Service bulletin. Some 2024-2026 Explorer/Aviator/Police Interceptor Utility vehicles may exhibit an illuminated malfunction indicator (MIL) lamp with engine over-temperature warning in the message center and poor air conditioning (A/C) performance from the engine cooling fan not running. Diagnostic trouble codes (DTC) B3A1B, P0113, P0217, and/or P0480 may be stored in the powertrain control module (PCM). This may be due to poor engine compartment ground connections at G105, G107, G111 and/or G122. Refer to the Wiring Diagram (WD) > Grounds Cell 010 > Pages 2, 3, 7 and 8. Prior to any Workshop Manual (WSM) diagnostics, verify all listed grounds are tightened to 62 lb-in (7 Nm) to resolve this condition. If symptoms or DTCs return after all grounds are tightened, follow normal WSM diagnostics. |
| SSM 54756 | 2026-04-21. Service bulletin. 2021-2026 Explorer vehicles equipped with the 2.3L EcoBoost engine may require air conditioning (A/C) compressor belt removal for various reasons. The Workshop Manual (WSM), Section 303-05A Accessory Drive - 2.3L EcoBoost > Removal and Installation > Air Conditioning (A/C) Compressor Belt procedure has been revised to eliminate cutting the A/C compressor belt to remove it. Refer to the updated procedure to reuse the belt. |
| SSM 54593 | 2026-02-27. Service bulletin. Some 2024-2025 F-150, Expedition/Navigator, Escape/Corsair, Bronco, Explorer, Mustang, Maverick vehicles equipped with a 1.5/2.0/2.3/3.5L EcoBoost engine and built on 01-Oct-2024 and through 31-May-2025 may exhibit an extended crank condition, strong fuel smell in the engine oil, high engine oil level and/or may have various drivability diagnostic trouble codes (DTCs) stored in the powertrain control module (PCM) with an illuminated malfunction indicator lamp (MIL). This may be due to an internal fuel leak of the high-pressure fuel pump causing fuel to enter the crankcase and reduce fuel pressure in the direct injection fuel rail. Diagnose this condition using Pinpoint Test HP located in Workshop Manual (WSM), Section 303-04. If no DTCs are stored in the PCM, proceed from Step HP1 to Step HP5 and continue testing. Repair as necessary outside of this article. For claiming, if high-pressure fuel pump replacement is required, use causal part number 9D376 and labor operation code 9543A. If the root cause is identified as anything other than the fuel injection pump, claim the repair outside of this article. |
| SSM 54544 | 2026-02-12. Service bulletin. Some 2025 Bronco/Ranger vehicles equipped with a 2.7L EcoBoost engine may exhibit an illuminated malfunction indicator lamp (MIL) with diagnostic trouble code (DTC) P04DB stored in the powertrain control module (PCM) with no other relevant DTCs present. Refer to Workshop Manual (WSM), Section 303-08B Engine Emission Control > Diagnosis and Testing > Crankcase Ventilation > Pinpoint Test > steps HG1-3 to check for leaks in the positive crankcase ventilation (PCV) and repair as needed. If no leaks are found in the PCV system, this condition may be due to the software in the PCM. This condition does not affect vehicle durability and no additional diagnosis is required for this condition at this time. The replacement of components or reprogramming of modules will not resolve this condition. Clear the DTC and return the vehicle to the customer. Inform customers that they can continue to drive the vehicle and engineering is currently working on a solution for this condition that is expected in Q2 2026. If a vehicle comes in for this condition, submit a Global Concern Report (GCR) and monitor Professional Tech |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.