Transport Canada recall 2013118
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | Transport Canada (Canada) |
|---|---|
| Campaign number | 2013118 |
| Manufacturer's number | PC225, PC226 |
| Reported | 2013-04-12 |
| Component | Brakes |
| Notification type | Safety Mfr |
| Units potentially affected | 876 |
What is wrong
On certain vehicles, the front brake caliper mounting brackets may have been manufactured incorrectly and could fail, which could result in a loss of vehicle control. This could also increase stopping distances. Both issues could result in a crash causing property damage and/or personal injury. Correction: Dealers will inspect and, if necessary, replace one or both front brake caliper mounting bracket(s).
| 2013 INFINITI JX35 | |
|---|---|
| 2013 NISSAN PATHFINDER |
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| NTB10-145B | 2023-04-06. Service bulletin. ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. |
|---|---|
| ITB10-074B | 2023-04-04. Service bulletin. ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. |
| NTB14114A | 2021-05-10. Service bulletin. IF YOU CONFIRM All "hands free" functions of the Intelligent Key (I-Key) do not work. For example, the doors will not lock or unlock when pressing either front door request switch. NOTE: - The issue of all I-Key "hands free" functions not working may occur intermittently or all the time. - The message "No Key Detected" or similar may show on the Vehicle Information Display (located in the combination meter). - All I-Key remote button functions (door lock/unlock, etc.) WILL work normally when all I-Key "hands free" functions are NOT working. ACTION 1. Inspect the I-Key?s battery on its negative contact side. 2. If excessive scratching is found, replace the battery. 3. Verify all I-Key functions (both "hands free" and remote) work properly after battery replacement. NOTE: Do NOT replace the BCM, I-Key, or other parts for the issue described under IF YOU CONFIRM, if it should occur. See this bulletin for further detail. |
| NTB13088A | 2021-05-10. Service bulletin. SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail. |
| NTB15060 | 2021-05-10. Service bulletin. SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer is capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail. |
| NTB13101A | 2021-05-10. Service bulletin. IF YOU CONFIRM: The rubber weatherstrips on either one of the roof side molding assemblies (moldings) is coming loose from the molding itself. ACTION: Install self-adhesive foam tape and then replace both left and right moldings with the ones listed in PARTS INFORMATION. - Refer to SERVICE PROCEDURE for molding replacement. See this bulletin for further detail. |
| PC251 | 2021-05-10. Service bulletin. Infiniti is conducting a Retailer service action to inspect and, if necessary, replace one or both of the front brake torque members on certain specific 2013 Infiniti JX35 or 2014 Infiniti QX60 vehicles currently in Retailer inventory |
| NTB04094A | 2021-05-10. Service bulletin. If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail. |
| NTB00033E | 2021-05-10. Service bulletin. SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details. |
| NTB12066A | 2021-05-10. Service bulletin. SERVICE INFORMATION The 2013 Altima and Pathfinder have a new style Tire Pressure Monitoring System (TPMS). TPMS ID registration can be performed using one of the following procedures: - Transmitter Activation tool (J-45295-A) with CONSULT-III plus (preferred method) - Signal Tech II tool (J-50190) with CONSULT-III plus (preferred method) - Signal Tech II tool (J-50190) without CONSULT -III plus - CONSULT-III plus only Use the TPMS ID registration instructions in this bulletin as needed. |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.