Transport Canada recall 2013102
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | Transport Canada (Canada) |
|---|---|
| Campaign number | 2013102 |
| Manufacturer's number | N10 |
| Reported | 2013-04-05 |
| Component | Powertrain |
| Notification type | Safety Mfr |
| Units potentially affected | 1036 |
What is wrong
On certain vehicles, the tunnel heat shield may drop down and rub on the drive shaft, which could eventually result in the drive shaft breaking and loss of motive power. In conjunction with traffic and road conditions and driver reactions, this could increase the risk of a crash. A broken drive shaft could also impact the tunnel with sufficient force to cause airbag deployment. Unintended airbag deployment, in a non-warranted (non-impact) situation could startle the driver which could result in a vehicle crash causing property damage and/or personal injury. In some instances, inadvertent deployment could cause minor injuries to vehicle occupants. Correction: Dealers will install a heat shield support bracket.
| 2007 DODGE NITRO | |
|---|---|
| 2008 DODGE NITRO | |
| 2008 JEEP LIBERTY |
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| S1121000006RevA | 2022-09-26. Service bulletin. (Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns |
|---|---|
| 9004009 | 2022-09-26. Service bulletin. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. |
| 9004361 | 2022-09-26. Service bulletin. NAG1 Transmission Before installing the transmission with the engine, check for dowel pins (2) for alignment. If the pins are missing request to add the dowel pin first and then install the transmission |
| 9001784 | 2022-09-26. Service bulletin. Mechanical rocker arm, intake, 1.7 ratio. |
| N10040413 | 2022-07-18. Service bulletin. Some of the above vehicles may experience a condition where the underbody transmission tunnel shield may partially separate from the vehicle floor pan and contact the aluminum driveshaft. Operating the vehicle with the transmission tunnel shield rubbing against the driveshaft could weaken the driveshaft at the rub point and cause it to break. |
| 9004361 | 2021-04-26. Service bulletin. NAG1 Transmission Before installing the transmission with the engine, check for dowel pins (2) for alignment. If the pins are missing request to add the dowel pin first and then install the transmission |
| N10040413 | 2021-03-15. Service bulletin. Some of the above vehicles may experience a condition where the underbody transmission tunnel shield may partially separate from the vehicle floor pan and contact the aluminum driveshaft. Operating the vehicle with the transmission tunnel shield rubbing against the driveshaft could weaken the driveshaft at the rub point and cause it to break. |
| S1121000006 Rev. | 2020-09-28. Service bulletin. (Revision A) No Start No Crank ? Starter Will Not Engage And There Are No Related Codes Or Concerns |
| SB-21-001-10 | 2010-10-27. Service bulletin. JEEP: MANUAL TRANSMISSION POPS OUT OF GEAR. THE TRANSMISSION POPS OUT OF FIRST GEAR WHILE ACCELERATING. THE CONDITION, MAY OCCUR INTERMITTENTLY AND MAY BE DIFFICULT TO DIAGNOSE. VERIFY THAT THE SHIFT BOOT IS NOT CAUSING THE ISSUE BY ENSURING THE BOOT IS NOT BINDING WHEN IN FIRST GEAR. *PE |
| 21-018-08 | 2008-10-03. Service bulletin. CHRYSLER/DODGE/JEEP: FLASH:DIAGNOSTIC TROUBLE CODE, DTC P0740 OR P1798 AND AUTOMATIC TRANSMISSION SHIFT IMPROVEMENTS 1-2 OR 2-3 COLD SHIFT IMPROVEMENTS. *PE |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.