Transport Canada recall 2011412
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | Transport Canada (Canada) |
|---|---|
| Campaign number | 2011412 |
| Manufacturer's number | 11327 |
| Reported | 2011-11-23 |
| Component | Lights And Instruments |
| Notification type | Compliance Mfr |
| Units potentially affected | 39 |
What is wrong
Certain vehicles fail to conform to Canada Motor Vehicle Safety Standard (CMVSS) 108 - Lighting System and Retroreflective Devices, as well as CMVSS 114 - Theft Protection and Rollaway Prevention. These vehicles were inadvertently programmed with incorrect Daytime Running Lamp (DRL) and theft protection calibration files during vehicle assembly. This could allow the driver to switch off the DRL system while the vehicle is underway. It could also allow non-dealership personnel to reprogram a replacement ignition key. A loss of DRL illumination could render the vehicle less visible to other motorists and to pedestrians during daylight hours, possibly resulting in a crash causing property damage and/or personal injury. Correction: Dealers will reprogram the Body Control Module.
| 2012 CHEVROLET VOLT |
|---|
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| 02-08-42-001J | 2024-01-19. Service bulletin. This informational bulletin provides information for dealers/technicians on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage. |
|---|---|
| PIC6089B | 2023-04-17. Service bulletin. This Preliminary Information communication provides information to the technician about vehicles that may have a Battery Saver Message or red Battery Indicator displayed in the Driver Information Center. Technician may find Diagnostic Trouble Code P0AF8 set in history. Technician will need to the 12 volt battery using the GR8 Battery tester. The technician will need to perform the Direct current Power Conversion Test published in Global Service Information to check for maximum current and voltage output. This test requires the use of a Carbon Pyle load tester. In addition, the technician can select the 14V Power Module Control Function in the Engine Control Module and Accessory Power Module Setpoint in the Body Control Module by using the Scan Tool in order to check that the system is able to respond to current loads. If the test fails, if there were low voltage Diagnostic Trouble Codes or P0AF8 was set, the technician should confirm that the 200 amp fuse located in the X50D Fuse Block is torqued to correct specification. Technician should check the voltage on both sides of the 200 amp Fuse while there is a load applied and comparing the voltage readings. Voltage drop can be checked from the positive battery post to the Accessory Power Module side of the 200 amp fuse as well. If the Accessory Power Module will output current under a load but the voltage is low on both sides of the fuse when compared to the voltage output at the Accessory Power Module, check the following Service Information for any other Diagnostic Trouble Codes that may have led to the low voltage condition, Accessory Power Module output terminal is clean and torqued to specification, The Accessory Power Module output cable ring terminal is properly seated to the Accessory Power Module output terminal post and its condition, and test the voltage drop on the ground cables to the engine block, transmission, body and chassis to ensure they are within specification. |
| 01-08-42-001O | 2023-02-28. Service bulletin. This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. |
| 21NA218 | 2022-02-14. Service bulletin. This bulletin provides a diagnostic service procedure to correct customer concerns of Reduced Propulsion (EREV), Malfunction Indicator Lamp (MIL) Illuminated with DTC P0C17, P1B03 and/or P0C01 Set. |
| 010842001N | 2021-08-09. Service bulletin. This service bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Water Leaks and Replacement Guidelines. |
| 010842001M | 2019-12-16. Service bulletin. This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines. |
| 010842001L | 2019-03-25. Service bulletin. This informational bulletin provides information for dealers/technicians on Exterior Lamp Condensation and Replacement Guidelines. |
| 01-08-42-001J | 2018-05-07. Service bulletin. This informational bulletin explains condensation in exterior lights and replacment guidelines for warranty replacement. |
| PI0645C | 2018-04-16. Service bulletin. This preliminary informational bulletin provides information on the driver airbag light is flashing in the cluster and/or the passenger airbag ON indicator does not illuminate when the passenger is present when the SDM setup has not been completed after reprogramming. |
| 02-08-42-001I | 2017-08-31. Service bulletin. This informational bulletin provides an out line on Headlamp, Tail Lamp, License Lamp or Fog/Driving Lamp Damage and what should be considered warranty replacement and not |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.