Transport Canada recall 2010438
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | Transport Canada (Canada) |
|---|---|
| Campaign number | 2010438 |
| Manufacturer's number | K33 |
| Reported | 2010-12-09 |
| Component | Brakes |
| Notification type | Safety Mfr |
| Units potentially affected | 13000 |
What is wrong
On certain vehicles equipped with a diesel engine and hydroboost brake system (which utilizes the power steering system pressure for brake assist), the power steering reservoir cap may have excessive vent pressure levels, which could result in a brake pedal that is slow to return once depressed. This could increase brake light illumination times and cause confusion to a following road user which, in conjunction with traffic, road conditions and driver's reactions, may result in a crash. Correction: Dealers will replace the power steering reservoir cap.
| 2010 DODGE RAM | |
|---|---|
| 2010 RAM 2500 | |
| 2011 RAM 2500 | |
| 2010 RAM 3500 | |
| 2011 RAM 3500 | |
| 2010 RAM 4500 | |
| 2011 RAM 4500 | |
| 2010 RAM 5500 | |
| 2011 RAM 5500 |
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| S1203000003 REV.A | 2026-07-02. Service bulletin. Trac-Rite Operation Diagnosis, Chatter, Shudder, Moving From A Stop And Turning |
|---|---|
| 9004351 | 2022-09-26. Service bulletin. PLATE - CLUTCH PRESSURE For 68RFE trans use selective fit pressure plates between the overdrive and reverse clutch packs and hence use all three 52119929A$, 52119930A$, 04799116A$ maintain clearance For 65RFE & 66RFE no selectives for this pressure plate: 65RFE use 04799116A$ 66RFE use 52119929A$ |
| M3411302012 | 2022-07-25. Service bulletin. Advanced Field Action Communication ? M3411302012 Chrysler Group LLC (Chrysler) announced a safety recall on certain 2009 and 2010 model year (DS) Ram 1500 series trucks and (ND) Dodge Dakota trucks equipped with a Chrysler built 9.25? rear axle. The above vehicles may have been built without an adhesive patch on the rear axle pinion nut threads. The lack of this adhesive patch could allow the rear axle pinion nut to loosen and/or the rear driveshaft to separate from the rear axle. A loose pinion nut could cause the rear axle to seize and a separated driveshaft could cause a loss of motive power. Excessive loosening of the rear axle pinion nut can allow the pinion gear to be drawn into the rear axle assembly, resulting in rear axle lock-up. Chrysler will conduct a voluntary safety recall on all affected vehicles to install a rear axle pinion nut retainer. Unfortunately, the parts required to provide a permanent remedy for this condition are currently not available. Chrysler anticipates the remedy parts will be available within the 1st quarter of 2013. An interim notification letter is being mailed to all involved vehicle owners. Chrysler is required by Federal law to inform all involved vehicle owners of a potential vehicle safety defect. |
| 9002350 | 2022-07-18. Service bulletin. Part Description: Integrated Trailer Brake Module Issue Description: Before replacing an Integrated Trailer Brake Module (ITBM) please review the following items.~ 1. The ITBM does not control the trailer lights. If the trailer lights are not working, do not change the ITBM.~ 2. If the Diagnostic Trouble Code(DTC) reported by the ITBM is C10C7-11 "Electronic Trailer Brake Control Output Short to Ground" or C10C7-12 "Electronic Trailer Brake Control Output Short to Battery", please verify the wiring on the trailer. The purpose of this faults is to protect the ITBM output from faulty trailer wiring.~ 3. If the customer complaint is ITBM not detecting the trailer connection. Do not change the ITBM until the system has been verified with load simulation and confirmed that ITBM is not recognizing the load. If load simulation indicates that the ITBM is operating properly, please verify the trailer wiring.~ 4. ITBM output will not be available if a trailer is not connect and plugged into the vehicle. The ITBM must detect a trailer before you will get trailer brake output.~ 5. Please follow the service manual procedures before changing the ITBM.~ This part can only be used as a replacement on vehicles with the Integrated Trailer Brake system already installed. Do not attempt to use this module for the purpose of adding the Integrated Trailer Brake system to a vehicle that was not originally equipped. You will encounter configuration difficulties. MOPAR has developed a kit, part number 82212548 to be used for installation of the Integrated Trailer Brake system on vehicles. |
| 18-005-13 | 2021-03-29. Service bulletin. Flash: Diagnostic and System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM) with new software.Trucks exhibiting any DTC related to Oxygen Sensor, Oxygen Sensor Module or communication to the Oxygen Sensor Module also require that Service Bulletin?s 25-004-12 (or later bulletin) must be performed (if not previously performed). Pick up trucks equipped with a 6.7L Cummins diesel have a number of software improvements/enhancements available. This SB will include improved robustness for DTC's: P2000 - NOX ABSORBER EFFICIENCY BELOW THRESHOLD P1451 - DIESEL PARTICULATE FILTER SYSTEM PERFORMANCE P0101 - MASS AIR FLOW SENSOR "A" CIRCUIT PERFORMANCE P046C - EGR POSITION SENSOR PERFORMANCE P049D - EGR CONTROL POSITION EXCEEDED LEARNING LIMIT P051B - CRANKCASE PRESSURE SENSOR CIRCUIT RANGE/PERFORMANCE P2002 - DIESEL PARTICULATE FILTER EFFICIENCY BELOW THRESHOLD P2262 - TURBOCHARGER BOOST PRESSURE NOT DETECTED - MECHANICAL P2609 - INTAKE AIR HEATER SYSTEM PERFORMANCE P245B - EGR COOLER BYPASS STATUS LINE INTERMITTENTVehicles flashed to address the above codes should be driven and repair validated. If code(s) return, follow diagnostic procedures available in DealerCONNECT/TechCONNECT.Improvements other than DTC robustness or enhancements: O2 Sensor cleaning cycle Correct Charge Air Cooler (CAC) out voltage reading in WiTech Improve idle shutdown messages Add ability to read Exhaust Manifold Presure (EMP) sensor value in WiTech Display correct Exhaust Gas Recirculation (EGR) position in WiTech Make Grid Heater off time selectable in WiTec Display correct alternator voltage in WiTech Turn Low Voltage Idle Up Off MIL on with no DTC Ability to read EGR valve gap on wiTECH Erroneous, brief brake lamp flash at key onSecure Bootloader softwareIf the Engine Control Module (ECM) does not have a calibration installed, or has an unapproved calibration installed then the ECM will |
| 9004351 | 2021-03-15. Service bulletin. PLATE - CLUTCH PRESSURE For 68RFE trans use selective fit pressure plates between the overdrive and reverse clutch packs and hence use all three 52119929A$, 52119930A$, 04799116A$ maintain clearance For 65RFE & 66RFE no selectives for this pressure plate: 65RFE use 04799116A$ 66RFE use 52119929A$ |
| 55502 | 2019-07-15. Service bulletin. PadKit- Front Disc Brake |
| 55488 | 2019-07-15. Service bulletin. PadKit- Front Disc Brake |
| 18-093-15 | 2019-05-20. Service bulletin. Flash: MIL Illumination With Transmission And Driveability Improvements This bulletin involves flash reprogramming the Powertrain Control Module (PCM) with new software. The customer may experience a MIL illumination. Upon further investigation the technician may find that any of the following erroneous Diagnostic Trouble Codes (DTCs): ? U0140 - Lost Communication With Body Control Module. 2010 DJ 5.7L (Sales Code EZC) Attempting to clear this DTC will be unsuccessful. ? P050D - Cold Start Rough Idle. ? P2181 - Cooling System Performance has been set. ? P0935 - Line Pressure Sensor Circuit High. All RFE transmissions. P0300 through P0308 - Multiple and Single Cylinder Misfire. This condition can occur when the vehicle is started cold and the driver immediately places the vehicle in drive and applies heavy throttle. Driveability and Transmission improvements are also included with this software release. These changes consist of the following: ? Enhanced clutch protection for more robust torque management during repeated fore and aft movement (rocking vehicle). All engines. ? A revised torque convertor lockup schedule that will reduce transmission temperatures in Tow/Cruise mode. All models equipped with RFE transmission. ? A Clunk sound or feel a shudder when the cruise control resume switch is pressed. This condition is most noticeable after the brakes were pressed to cancel cruise control and then the resume switch is pressed. All models equipped with RFE transmission. ? A shudder or shaking feeling when a wide open throttle (WOT) event is performed by the customer. This is most noticeable after the transmission downshifts during the WOT event. This condition will stop once the transmission upshifts. All models equipped with RFE transmission. ? A shudder or shaking feeling when accelerating from a stop under moderate throttle. This condition will stop once the transmission upshifts. All models equipped with RFE transmission. |
| 13317 | 2018-12-17. Service bulletin. Title Inspection and Return: Hydro-Booster, - Power Brake. Start Date: 10/27/2015 7:00 AM End Date Message You have been identified as either having stock, or have stock in transit to your dealership. Please return all suspect stock of part numbers: 68144663AA, 52013874AE. See the attached file for identifying suspect material. Please return suspect parts back to your facing depot using Return Code 02, before 17 November, 2015. Return any open orders in process too. Direct all questions via email to MOPARQC@fcagroup.com |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.