Transport Canada recall 2010402
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | Transport Canada (Canada) |
|---|---|
| Campaign number | 2010402 |
| Manufacturer's number | R172 |
| Reported | 2010-11-12 |
| Component | Steering |
| Notification type | Safety TC |
| Units potentially affected | 14407 |
What is wrong
On certain vehicles, corrosion may form in the lower steering column joint and limit the movement of the joint. Limited movement of this joint may create excessive load on the lower steering column shaft and, if the vehicle continues to be driven in this condition, may lead to cracking of the shaft during low speed manoeuvres that require large steering inputs. In an extreme case, the shaft may break which would result in loss of steering control and could result in a crash. Correction: Dealers will replace the affected column shafts and joints.
| 2002 NISSAN FRONTIER | |
|---|---|
| 2003 NISSAN FRONTIER | |
| 2004 NISSAN FRONTIER | |
| 2002 NISSAN XTERRA | |
| 2003 NISSAN XTERRA | |
| 2004 NISSAN XTERRA |
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| NTB08-097L | 2023-10-06. Service bulletin. DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. |
|---|---|
| NTB08-097K | 2023-03-07. Service bulletin. DIAGNOSIS OF VEHICLE PULL (DRIFT) AND/OR STEERING WHEEL OFF-CENTER This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. |
| NTB04094A | 2021-05-10. Service bulletin. If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail. |
| NTB00033E | 2021-05-10. Service bulletin. SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details. |
| NTB01083 | 2002-03-06. Service bulletin. VEHICLES MAY EXPERIENCE STEERING PULL DURING BRAKING. *JG |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.