Transport Canada recall 2005264
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | Transport Canada (Canada) |
|---|---|
| Campaign number | 2005264 |
| Manufacturer's number | E13 |
| Reported | 2005-09-09 |
| Component | Powertrain |
| Notification type | Safety Mfr |
| Units potentially affected | 2843 |
What is wrong
On certain vehicles equipped with a 3.7L engine and automatic transmission, water from the air conditioner evaporator drain tube may enter the transmission at the fill tube grommet seal. This can result in shudder during torque converter clutch engagement which, if ignored by the operator, could lead to increased transmission operating temperatures, boiling of the water, and a subsequent purging of transmission fluid into the engine compartment that could lead to a fire. Correction: Dealers will inspect the transmission for leakage at the fill tube grommet seal. If no leak is detected, a new fill tube grommet seal and water deflector shield will be installed, and proper alignment of the fill tube verified. If the presence of a leak is detected, the vehicle will be evaluated for a shudder condition and based on the evaluation, the transmission will either be triple flushed or the torque converter replaced as required and a new grommet seal and water deflector will be installed.
| 2005 JEEP GRAND CHEROKEE |
|---|
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| 101232 | 2024-11-07. Service bulletin. Plate - Planetary |
|---|---|
| 9004009 | 2022-09-26. Service bulletin. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. |
| 9004361 | 2022-09-26. Service bulletin. NAG1 Transmission Before installing the transmission with the engine, check for dowel pins (2) for alignment. If the pins are missing request to add the dowel pin first and then install the transmission |
| 9004009 | 2022-09-26. Service bulletin. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter. |
| 9001784 | 2022-09-26. Service bulletin. Mechanical rocker arm, intake, 1.7 ratio. |
| 9004178 | 2022-09-15. Service bulletin. DAMPER, Transfer Case Reman Transfer Case will arrive equipped with the Transfer Case Damper. Please return core with original damper intact. |
| 18-042-14 | 2022-08-15. Service bulletin. Generic Powertrain Control Module (PCM) Procedure This bulletin involves programming a generic PCM with software. |
| 21-022-14 REV. A | 2022-08-15. Service bulletin. 4WD Lamp Illuminated and Diagnostic Trouble Code C140F Active in Final Drive Control Modules (FDCM) Memory This bulletin involves verifying FDCM software level and then flash reprogramming of the FDCM with new software. Customers may indicate that the ?Service 4WD? indicator in the instrument cluster is illuminated. They may also indicate that the transfer case will not shift from 4WD High, 4WD Low, and/or Neutral once the lamp is illuminated. Further investigation identifies that a Diagnostic Trouble Code C140F is stored or active in the Final Drive Control Modules (FDCM) Memory |
| 21-022-14 | 2022-08-15. Service bulletin. 4WD Lamp Illuminated and Diagnostic Trouble Code C140F Active in Final Drive Control Modules (FDCM) Memory This bulletin involves verifying FDCM software level and then flash reprogramming of the FDCM with new software. Customers may indicate that the ?Service 4WD? indicator in the instrument cluster is illuminated. They may also indicate that the transfer case will not shift from 4WD High, 4WD Low, and/or Neutral once the lamp is illuminated. Further investigation identifies that a Diagnostic Trouble Code C140F is stored or active in the Final Drive Control Modules (FDCM) Memory |
| 9004361 | 2021-04-26. Service bulletin. NAG1 Transmission Before installing the transmission with the engine, check for dowel pins (2) for alignment. If the pins are missing request to add the dowel pin first and then install the transmission |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.