Transport Canada recall 2005184
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | Transport Canada (Canada) |
|---|---|
| Campaign number | 2005184 |
| Manufacturer's number | 05059 |
| Reported | 2005-06-21 |
| Component | Brakes |
| Notification type | Safety Mfr |
| Units potentially affected | 3886 |
What is wrong
Certain vehicles do not comply with the requirements of CMVSS 135. To meet the Standard, the vehicle must not move for five minutes when stopped on a steep hill with the parking brake applied and the vehicle in NEUTRAL (N). A part that was not manufactured to specifications can cause the parking brake to fail this test. A loud popping noise as the parking brake is applied or a sudden decrease in the effort required to apply the parking brake can be indications of this condition. When the parking brake is released, the driver may notice unintended braking when accelerating, decelerating, or coasting, and a groan, humming, and/or vibration coming from the rear of the vehicle. Correction: Dealers will inspect for parking brake lever slippage at each rear brake caliper. The calipers will be replaced if lever slippage is identified.
| 2005 BUICK TERRAZA | |
|---|---|
| 2005 CHEVROLET UPLANDER | |
| 2005 PONTIAC MONTANA SV6 | |
| 2005 SATURN RELAY |
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| PIP4723F | 2022-02-14. Service bulletin. This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update. |
|---|---|
| PIT3271J | 2019-12-09. Service bulletin. This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection. |
| 00-05-22-002N | 2018-06-04. Service bulletin. This informational bulletin provides information for Disc Brake Warranty Service and Procedures. |
| 01-00-89-010J | 2018-05-21. Service bulletin. This informational bulletin provides a revision for 01-00-89-010I to add the 2013 model year. |
| 00-05-22-002O | 2018-05-07. Service bulletin. This informational bulletin provides technicians with a brake lathe calibration procedure. |
| 00-05-22-002O | 2017-08-15. Service bulletin. This informational bulletin provides technicians with a brake lathe calibration procedure. |
| 06-00-89-026L | 2017-08-15. Service bulletin. This warranty administration bulletin provide policy information on a revised customer concern not duplicated/verified labor operation numbers and how to submit CCND. |
| PIT4907A | 2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. |
| PIT4943C | 2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay. |
| 3743 | 2007-12-13. Service bulletin. VARIOUS ABS DTC'S AND INTERMITTENT CONCERNS. *NJ |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.