Transport Canada recall 2004198
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | Transport Canada (Canada) |
|---|---|
| Campaign number | 2004198 |
| Manufacturer's number | 04049 |
| Reported | 2004-06-16 |
| Component | Brakes |
| Notification type | Safety Mfr |
| Units potentially affected | 3238 |
What is wrong
On certain vehicles, two bolts that attach the front brake caliper to the steering knuckle on the left and right front wheel assemblies were not tightened adequately. If too much movement occurs between the caliper bracket and knuckle, the bolt(s) may back out or fracture. Depending on whether one or both bolts back out or fracture, the result can be: 1) locking of the affected wheel during braking and an abrupt steering input in the direction of the locked wheel, 2) reduced braking and noise from the affected wheel, or 3) severing of a brake hose, increased brake pedal travel, and reduced steering control. If this were to occur, it could result in a vehicle crash without prior warning. Correction: Dealers will tighten both bolts to the specified torque.
| 2004 CHEVROLET IMPALA | |
|---|---|
| 2004 CHEVROLET MONTE CARLO | |
| 2004 PONTIAC GRAND PRIX |
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| PIP4723F | 2022-02-14. Service bulletin. This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update. |
|---|---|
| PIT3271J | 2019-12-09. Service bulletin. This Preliminary Information communication provides information to the technician about changing the tire and wheel size on vehicles. General Motors will only support a tire calibration for tires that have been sized, tested and designed for the vehicle in question and its applications. Technician should not use the information that is provided by the antilock braking system tire size selection. |
| PIT4907A | 2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician about brake rotors on new vehicles and replacement parts from General Motors Service Parts Operations. Technician should be advised the costing should not be removed from the brake rotor it will wear off with normal brake usage. Dealer should communicate to the customer this condition is a normal operating characteristic of their vehicle. |
| PIT4943C | 2017-08-15. Service bulletin. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay. |
| 4615 | 2007-10-31. Service bulletin. ABS PUMP RUNNING WHEN NOT NEEDED. *NJ |
| 3853 | 2006-08-21. Service bulletin. ABS LAMP ON AND CURRENT OR HISTORY DTCS C1223, C1224, C1227, C1228, C1234, AND/OR C1235. *TT |
| 3583 | 2006-05-16. Service bulletin. ABS LAMP ON AND CURRENT OR HISTORY DTCS C1233, C1224, C1227, C1228, C1234, AND/OR C1235. *TT |
| 3500 | 2006-02-23. Service bulletin. ABS LIGHT ON AND POSSIBLE DIAGNOSTIC TROUBLE CODES. *AK |
| 709 | 2005-12-16. Service bulletin. CAR ISSUES - FIX IT RIGHT THE FIRST TIME (NEW ISSUES IN BOLD). TO INCLUDE 2006 AND 2007 MODELS. GM. TECH LINK. *TT |
| 3500 | 2005-11-01. Service bulletin. ABS LIGHT COMING ON AND CODES C1225, C1226, C1232, C1233, C1276 AND/OR C1277 ARE FOUND IN THE EBCM. *TT |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.