Transport Canada recall 2002196
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | Transport Canada (Canada) |
|---|---|
| Campaign number | 2002196 |
| Manufacturer's number | 02051 |
| Reported | 2002-10-28 |
| Component | Electrical |
| Notification type | Safety Mfr |
| Units potentially affected | 24 |
What is wrong
On certain vehicles, the windshield wiper motor may fail during use because of improper manufacture. If this were to occur in severe weather, driver visibility could be reduced, which could result in a vehicle crash without prior warning. Correction: Dealer will inspect and, if necessary, replace the wiper motor assembly.
| 2003 HUMMER H2 | |
|---|---|
| 2003 SATURN LS | |
| 2003 SATURN LW |
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| PIP4723J | 2024-10-25. Service bulletin. This Preliminary Information communicates to the dealer the process for downloading or updating operating software for the Tire Pressure Monitor, Active Fuel Injector tester, multi media tester, PICO Scope, GR8 starting/charging tester and Vehicle Data Recorder tools, giving website address and step by step instructions to complete the update. |
|---|---|
| General Communication | 2024-08-26. Service campaign. Vehicle Wide Programming (VWP) is a new process to update software on GM Vehicles. It provides the ability via a single selection within Techline Connect to first identify which modules need updating and then proceed to updating affected modules (with some exceptions). The updating of modules is completed in parallel instead of the technician needing to update one module at a time. This allows a more streamlined approach for dealers and customers. |
| 24-NA-098 | 2024-06-25. Service bulletin. This service bulletin provides information for dealers/technicians on Service Programming System (SPS) Error Codes E4398, E4399, E4401, E4403, M4404, M4413, M6954, M6955, E4414, E4423, E4491, E4492, or E6961 and resolution information. |
| 10-08-45-001H | 2024-04-05. Service bulletin. This bulletin provides information for electrical ground repairs using new General Motors replacement fasteners with conductive finish. |
| 07-08-49-020R | 2023-10-18. Service bulletin. This informational bulletin provides information for the IPC odometer programming method quick reference guide. |
| PIT3665M | 2023-06-13. Service bulletin. This Preliminary Information communication advises the technician that the Hydro-Boost is not serviceable and will need to be replaced if the brake pedal moves or applies on its own at a full turn. |
| 23-NA-001 | 2023-01-25. Service bulletin. This service bulletin provides information for dealers/technicians on OnStar Module 2G Sunset Information. |
| 15-NA-079 | 2021-04-20. Service bulletin. OnStar® Voice Fallback Number Update Some customers may have received a letter from OnStar® stating that "We recently tried to provide a software update to the OnStar® hardware in your vehicle. However, your system could not be updated remotely. As a result, some of your OnStar® system functions may not be working as expected." The customer is further instructed in this letter to "Please contact your dealer – or any dealer near you – as soon as possible to schedule an appointment for this no-cost software update. Your dealer will reprogram your OnStar® module with an update. This is for vehicles that have previously received the Canada upgrade as described in Service Bulletin #15-08-44-001F." |
| 07-08-49-020J | 2021-04-20. Service bulletin. IPC Odometer Programming Method Quick Reference Guide Season Odometer Programming Methods in Use Today 1. IPC reprogramming and setup using the service programming system (SPS). 2. Odometer setup at the electronic service center (ESC) when using an exchange IPC/DIC. 3. Tech 2® – The Tech 2 is used to set up a replacement BCM, which includes loading the odometer value that is displayed and stored in the IPC. A replacement IPC will display the previously stored vehicle odometer value, communicated from the BCM, after cycling the ignition or driving the vehicle. *The odometer programming is integrated as part of the BCM programming procedure. It is not a stand-alone event. |
| 070849020M | 2021-04-16. Service bulletin. IPC Odometer Programming Method Quick Reference Guide |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.