NHTSA recall 26V560000
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | NHTSA (United States) |
|---|---|
| Campaign number | 26V560000 |
| Manufacturer's number | 83D |
| Manufacturer | Chrysler (FCA US, LLC) |
| Reported | 2026-09-01 |
| Owners notified | 2026-09-24 |
| Component | BACK OVER PREVENTION:SOFTWARE |
| Units potentially affected | 239130 |
| Part numbers | Please see attached supplemental information titled FCA US LLC Recall Part Numbers-83D-09012026.pdf |
What is wrong
Chrysler (FCA US, LLC) is recalling certain 2025-2026 Ram 1500 vehicles. A radio software error may cause the rearview camera image not to display. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 111, "Rear Visibility."
What can happen
A rearview image that does not display reduces the driver's view behind the vehicle, increasing the risk of a crash.
The remedy
The radio software will be updated over-the-air (OTA) or by a dealer, free of charge. Owner notification letters were mailed September 24, 2026. Owners may contact Chrysler customer service at 800-853-1403. Chrysler's number for this recall is 83D. Vehicle Identification Numbers (VINs) involved in this recall will be searchable on NHTSA.gov on September 9, 2026.
| 2025 RAM 1500 | Built from 2023-10-06. |
|---|---|
| 2026 RAM 1500 | Built to 2026-02-23. |
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| 114282 | 2026-09-03. Warranty extension. ***Recall Completion Prior to Sale of Vehicle*** |
|---|---|
| 114283 | 2026-09-03. Warranty extension. ***Recall Completion Prior to Sale of Vehicle*** |
| 9100480 | 2025-01-16. Service bulletin. Park Sensor Vehicles can have a warning in the cluster indicating that the park sensors are inoperative and to wipe the park sensors. If the sensors are clean and the message is still present there are 2 items that need to be checked - 1. Verify that the decoupling ring, the thin rubber ring directly around each park sensor, is not rolled or pinched. If an edge is rolled it can put excessive pressure on the sensor and cause the module to think that the sensor is blocked. 2. Verify the PAM PN. If the PN is 56029962AH, then the s/w is old and requires an update to at least 56029962AI level to fix the issue. If the PAM PN is 56029962AH please update it to the latest available PN. |
| 9100479 | 2025-01-15. Service bulletin. Park Sensor Vehicles can have a warning in the cluster indicating that the park sensors are inoperative and to wipe the park sensors. If the sensors are clean and the message is still present there are 2 items that need to be checked - 1. Verify that the decoupling ring, the thin rubber ring directly around each park sensor, is not rolled or pinched. If an edge is rolled it can put excessive pressure on the sensor and cause the module to think that the sensor is blocked. 2. Verify the PAM PN. If the PN is 56029962AH, then the s/w is old and requires an update to at least 56029962AI level to fix the issue. If the PAM PN is 56029962AH please update it to the latest available PN |
| S2523000001 | 2025-01-09. Service bulletin. C00C4-97 And Or C00C5-97 - Rear Radar Module Component Or System Operation Obstructed Or Blocked. |
| S2423000049 | 2024-11-18. Service bulletin. Blind Spot Warning Displayed On Instrument Cluster. Mid Range Radar Left And Or Right Setting C00C4-76 C00C5-76 Rear Radar Module Wrong Mounting Position. |
| 9100414 | 2024-09-26. Service bulletin. Parking assist Vehicles can have a warning in the cluster indicating that the park sensors are inoperative and to wipe the park sensors. If the sensors are clean and the message is still present there are 2 items that need to be checked - 1. Verify that the decoupling ring, the thin rubber ring directly around each park sensor, is not rolled or pinched. If an edge is rolled it can put excessive pressure on the sensor and cause the module to think that the sensor is blocked. 2. Verify the PAM PN. If the PN is 56029962AH, then the s/w is old and requires an update to at least 56029962AI level to fix the issue. If the PAM PN is 56029962AH please update it to the latest available PN. |
| 08-123-24 | 2024-06-07. Service bulletin. "Flash: Park Assist Module (PAM) Updates Customers may experience the following: ● A pop-up on the Instrument Panel Cluster (IPC) telling customer to wipe off the Park Assist Sensors (PAS), even though nothing is actually on the sensors. When this IPC pop-up is present, the front Parksense feature is disabled Fig. 1. This bulletin involves reprogramming the PAM with the latest software available." |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.