NHTSA recall 16V219000

A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.

Campaign
Published by	NHTSA (United States)
Campaign number	16V219000
Manufacturer	Nissan North America, Inc.
Reported	2016-04-15
Owners notified	2016-11-18
Component	STRUCTURE:BODY:HATCHBACK/LIFTGATE:SUPPORT DEVICE/STRUT
Units potentially affected	108503

Remedy progress the manufacturer reported
Report	Quarterly report 6, for 2018 quarter 1
Filed with NHTSA	2018-04-30
Vehicles in the campaign	108503
Reported remedied	86198 (79%)
Reported unreachable	0
Reported removed	0

These are the manufacturer's totals for the whole campaign at the end of 2018 quarter 1, as filed with NHTSA. They do not say whether one vehicle has been remedied: check the VIN with the official lookups. The reports are from data as of 2026-10-19.

What is wrong

Nissan North America, Inc. (Nissan) is recalling certain model year 2014-2016 Nissan Rogue vehicles manufactured July 31, 2013, to January 16, 2016. In the affected vehicles, the rear lift gate support stays may corrode due to insufficient anti-corrosion treatment.

What can happen

Corrosion of one or both of the rear lift gate support stays could cause a sudden release of pressure. If this occurs, the support stays may break off, increasing the risk of injury.

The remedy

Nissan will notify owners, and dealers will replace the rear tailgate stays, free of charge. The recall began on November 18, 2016. Owners may contact Nissan customer service at 1-800-647-7261.

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

Vehicles this campaign lists
2014 NISSAN ROGUE	Built 2013-07-31 to 2016-01-16.
2015 NISSAN ROGUE	Built 2013-07-31 to 2016-01-16.
2016 NISSAN ROGUE	Built 2013-07-31 to 2016-01-16.

A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.

Bulletins for the same vehicles and component

Bulletins for the same vehicles and component
NTB09-131C	2026-04-29. Service bulletin. CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB09-131C	2026-04-29. Service bulletin. CERTIFICATION LABEL AND VIN PLATE REPLACEMENT SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement “Certification Label” or “VIN Plate/Label” may be needed. HINT: Certification Label = FMVSS (Federal Motor Vehicle Safety Standards) label. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. · The “VIN Plate/Label” (metal plate or vinyl label) is attached to the instrument panel or body on the driver side at the base of the windshield (see Figure 1). · The “Certification Label” (vinyl adhesive label) is located on the lower area of the driver side B-Pillar (see Figure 1).
NTB13-028H	2023-03-07. Service bulletin. REMOVING FOREIGN MATERIAL FROM THE WINDOW GLASS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB09-081J	2023-03-07. Service bulletin. WINDSHIELD CRACKING This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB15062A	2021-05-10. Service bulletin. IF YOU CONFIRM There is a popping noise from either the right or the left front coil springs when turning to the right or left. NOTE: Electronic chassis ears may be helpful in isolating this type of noise. ACTION Replace both front coil springs, strut mount bearings, and all other parts listed under PARTS INFORMATION. Position the coil springs as shown on pages 2-5. Check the front end alignment, adjust to factory specifications as needed. NOTE: Refer to the Electronic Service Manual (ESM), section FSU Front Suspension, for strut coil spring removal, installation, and alignment information. IMPORTANT: The Coil Spring Installation Guidelines section in this bulletin MUST be followed in order for a correct repair to be performed.
NTB15070	2021-05-10. Service bulletin. IF YOU CONFIRM An oil leak from the Adapter Case Oil Seal or the O-ring (see Figure 1). ACTION NOTE: DO NOT replace the Transfer Case for a leak from the Adapter Case Oil Seal or the O-ring. Reseal the Adapter Case with the seals listed in PARTS INFORMATION and shown in Figure 1. * Please see this bulletin for further details.
NTB14105	2021-05-10. Service bulletin. IF YOU CONFIRM: The carpet is wet on the driver and/or front passenger floor (see Figure 1). - A "sloshing" type noise may be heard while driving AND the source of the wetness is not caused by the air conditioning system. ACTION: 1. Determine if the leak is from the kick panel and/or cowl end area. 2. If confirmed, apply body sealant to the incident areas as outlined in this bulletin. See this bulletin for further detail.
PC315	2021-05-10. Service bulletin. Nissan is conducting a dealer service action of the rear lift gate hinge mounting bolt torque on 1,372 specific 2014 Rogue vehicles identified in SERVICE COMM.
NTB14047	2021-05-10. Service bulletin. IF YOU CONFIRM: The "front door power window and door lock/unlock switch (RH) finisher" (switch finisher) has a loose fit, causting an excessive gap. See Figure 1. ACTION: 1. Remove the passenger front door finisher (door finisher). - Refer to the Electronic Service Manual (ESM), section INT-Interior, for removal procedure. 2. Install a foam block where shown in SERVICE PROCEDURE. - Use the foam block listed in PARTS INFORMATION. 3. Install the door finisher with a new switch finisher listed in PARTS INFORMATION. - Refer to the ESM, section INT-Interior, for installation procedure. See this bulletin for further detail.
PC255	2021-05-10. Service bulletin. Nissan is conducting a Dealer Service Action to inspect for water leaks at the rear liftgate glass on certain specific 2014 Nissan Rogue vehicles currently in dealer inventory.

A bulletin is the manufacturer's note to its dealers. It is not part of this recall.