NHTSA recall 15V882000
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
| Published by | NHTSA (United States) |
|---|---|
| Campaign number | 15V882000 |
| Manufacturer | BMW of North America, LLC |
| Reported | 2015-12-28 |
| Owners notified | 2016-02-08 |
| Component | ELECTRONIC STABILITY CONTROL (ESC) |
| Units potentially affected | 16 |
| Report | Quarterly report 5, for 2017 quarter 1 |
|---|---|
| Filed with NHTSA | 2017-04-22 |
| Vehicles in the campaign | 16 |
| Reported remedied | 16 (100%) |
| Reported unreachable | 0 |
| Reported removed | 0 |
These are the manufacturer's totals for the whole campaign at the end of 2017 quarter 1, as filed with NHTSA. They do not say whether one vehicle has been remedied: check the VIN with the official lookups. The reports are from data as of 2026-10-19.
What is wrong
BMW of North America, LLC (BMW) is recalling certain model year 2015 i8 vehicles manufactured May 29, 2015, to June 5, 2015. Improperly drilled holes within the Dynamic Stability Control (DSC) hydraulic unit may restrict one or more pistons impairing the DSC functions, including braking.
What can happen
Impaired DSC functionality may negatively impact vehicle handling and braking and increase the risk of a crash.
The remedy
BMW will notify owners, and dealers will inspect the DSC hydraulic unit, and replace if necessary, free of charge. The recall began on February 8, 2016. Owners may contact BMW customer service at 1-800-525-7417.
Notes
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
| 2015 BMW I8 | Built 2015-05-29 to 2015-06-05. |
|---|
A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.
Bulletins for the same vehicles and component
| B610920 | 2020-04-20. Service bulletin. CHECK CONTROL MESSAGES FOR BRAKE SUSPENSION AND AIR BAG SYSTEM MALFUNCTION: Multiple check control messages (CCM) can display for brake suspension and air bag system malfunction. The customer may also complain about any of the following: Engine can no longer be switched off Drive position (D) cannot be engaged on the gear selector switch (GWS) Reduction of steering assist After an engine emergency shut-off (either a prolonged long press; or 3 consecutive short presses of the Start/Stop button) and the vehicle going to sleep (identifiable by the lighting of the "Start/Stop button") everything resumes normal functionality and the CCM messages no longer appear. |
|---|---|
| B340517 | 2020-04-20. Service bulletin. TICKING NOISE WHILE CORNERING WITHOUT THE BRAKES APPLIED: This Service Information Bulletin (Revision 3) replaces SI B34 05 17 dated September 2017. Ticking noise coming from front wheel while cornering without brakes applied noticeable at low speeds. The vehicle must be moving. See attached video V34 01 20 Note: For a similar noise heard when parking with the brakes applied refer to SIB 31 01 12. Microscopic movement of the contact interface between the inner brake disc and the wheel bearing flange on vehicles equipped with lightweight brake discs. |
| B660115 | 2018-12-17. Service bulletin. Surround View Camera Last User Mode Operation Change. After programming with ISTA/P 2.53.5 or a more recent version, the rear camera view is displayed when the reverse gear is selected. The vehicle does not remember the last user mode (surround/top camera view). INFORMATION An operational concept change for the surround/top camera view was introduced with ISTA/P 2.53.5 (I-level Fxx-14-07-505). When the reverse gear is selected, the default view will be the rear camera. The surround/top camera view has been removed from the last user mode function. This is to meet the upcoming (new) federal regulations regarding rear view cameras. Note: The surround/top camera view is available, but the driver must manually switch the camera view using the iDrive controller. |
| B650715 | 2018-12-10. Service bulletin. "This Service Information bulletin supersedes SI B65 07 15 dated April 2015. designates changes to this revision SUBJECT Airbag Warning Light ON: Fault 930BE8, High-voltage System Shutdown . The airbag warning light in the instrument cluster is on, or the check control message (CCM) ""Restraint system faulty"" is displayed. The advance crash safety module (ACSM4I) has fault code 930BE8 ""High-voltage system switchoff Range extender Electrical Machine Electronics (REME)/battery management electronics: Resistance too high"" stored. A sporadically poor connection causes high resistance in the airbag ignition circuit." |
| B662116 | 2018-11-05. Service bulletin. KAFAS CAMERA-BASED ASSISTANCE SYSTEM LIMITS. INFORMATION The situations described above may all be caused by known limitations of the system such as: Dirty windshield Incomplete calibration process Unsuccessful calibration Restricted visibility- weather conditions or parked vehicles Missing lamps on target vehicle Non-standard vehicle exterior surfaces Insufficient ambient lighting Abrupt motion of target vehicle. |
A bulletin is the manufacturer's note to its dealers. It is not part of this recall.