NHTSA recall 15V507000

A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.

Campaign
Published by	NHTSA (United States)
Campaign number	15V507000
Manufacturer	Nissan North America, Inc.
Reported	2015-08-12
Owners notified	2015-09-14
Component	VEHICLE SPEED CONTROL:ACCELERATOR PEDAL; SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES
Units potentially affected	298747

Remedy progress the manufacturer reported
Report	Quarterly report 6, for 2016 quarter 4
Filed with NHTSA	2017-01-31
Vehicles in the campaign	298747
Reported remedied	175712 (58%)
Reported unreachable	0
Reported removed	0

These are the manufacturer's totals for the whole campaign at the end of 2016 quarter 4, as filed with NHTSA. They do not say whether one vehicle has been remedied: check the VIN with the official lookups. The reports are from data as of 2026-10-19.

What is wrong

Nissan North America, Inc. (Nissan) is recalling certain model year 2012-2015 Nissan Versa sedan vehicles manufactured June 9, 2011, to March 11, 2015, and 2014-2015 Nissan Versa Note vehicles manufactured April 23, 2013, to March 11, 2015. The affected vehicles have a center console trim panel that may catch the driver's shoe and delay the transition from the accelerator pedal to the brake pedal.

What can happen

A delay in the application of the brake pedal would lengthen the distance needed to stop the vehicle and increase the risk of a crash.

The remedy

Nissan will notify owners, and dealers will modify the console trim panel, free of charge. The recall began on September 14, 2015. Owners may contact Nissan customer service at 1-800-647-7261.

Notes

Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

Vehicles this campaign lists
2012 NISSAN VERSA	Built 2011-06-09 to 2015-03-11.
2013 NISSAN VERSA	Built 2011-06-09 to 2015-03-11.
2014 NISSAN VERSA	Built 2011-06-09 to 2015-03-11.
2015 NISSAN VERSA	Built 2011-06-09 to 2015-03-11.
2014 NISSAN VERSA NOTE	Built 2013-04-23 to 2015-03-11.
2015 NISSAN VERSA NOTE	Built 2013-04-23 to 2015-03-11.

A vehicle with no link is not in this site's catalog, which covers cars, multipurpose vehicles and trucks by model year. The campaign is from data as of 2026-10-19.

Investigated as EA15003

This recall followed 1 NHTSA investigation. An investigation is NHTSA looking into a possible defect. It is not a finding that a defect exists, and it does not say that any one vehicle is affected.

NHTSA investigations that led to this recall
EA15003	Engineering analysis, opened 2015-04-01, closed 2015-09-01. Pedal Operation Interference. SERVICE BRAKES, HYDRAULIC; SERVICE BRAKES, HYDRAULIC:PEDALS AND LINKAGES; VEHICLE SPEED CONTROL:ACCELERATOR PEDAL.

From NHTSA's investigation file, as of 2026-10-19. The JSON has NHTSA's summary of each.

Bulletins for the same vehicles and component

Bulletins for the same vehicles and component
NTB10-145B	2023-04-06. Service bulletin. ABS/VDC CAN DIAGNOSIS INFORMATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB13088A	2021-05-10. Service bulletin. SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail.
NTB15060	2021-05-10. Service bulletin. SERVICE INFORMATION When servicing run flat tires or low profile tires: - Special equipment and procedures are required to avoid damage. - Specifically, Tire Pressure Monitor transmitters (TPMS sensors) can be damaged when improperly dismounting and mounting tires. - TPMS sensors becoming damaged during mounting or dismounting tires are not covered under warranty. - To avoid such damage, ensure that the tire changer being used and the operator of the tire changer is capable of servicing run flat and low profile tires. - Operator?s manuals for such tire changers must be followed. See this bulletin for further detail.
PC383A	2021-05-10. Service bulletin. Nissan is conducting a dealer inventory inspection on certain 2015 Sentra, 2015 Versa Note to inspected and, if necessary, replace the driver's side door locks.
PC383	2021-05-10. Service bulletin. Effective immediately, Nissan is placing a temporary Quality Assurance (QA) Hold on approximately 1,036 MY 2015 Sentra and Versa Note vehicles because the door latch may not fully engage. This issue is still under investigation.
NTB04094A	2021-05-10. Service bulletin. If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail.
NTB00033E	2021-05-10. Service bulletin. SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details.
PM365A	2021-05-10. Service bulletin. Nissan is conducting a dealer service action to replace the rear seat back latch bolts on certain specific MY14 Versa Note vehicles.
NTB13038	2021-05-10. Service bulletin. SERVICE INFORMATION The "Lock / Unlock request buttons" that are located on the outside door handles of vehicles with Intelligent Key can be disabled (or enabled) through either the "Comfort & Conv." settings of the Audio/Visual/Navigation system, orthrough the "Combination Meter settings" depending on the vehicle model, year and trim level. NOTE: In some instances this feature may be unintentionally disabled. Please verify the status of this feature before any further diagnostic is performed. Please see this bulletin for further details.
NTB17-041	2017-10-25. Service bulletin. ADDITIONAL SERVICE WHEN REPLACING CONTROL VALVE OR TRANSAXLE ASSEMBLY SERVICE INFORMATION After a CVT assembly or control valve replacement, additional service must be completed with CONSULT-III plus (C-III plus). - The original calibration data must first be erased from the TCM and then newcalibration data written. - If the calibration data is not erased, the vehicle can experience drivability concernswhich may result in a CVT issue. Additional Service when Replacing Control Valve or Transaxle Assembly - The following procedures, starting on the next page, must be performed in thisorder. - Check off procedure as they are performed in the order listed below.

A bulletin is the manufacturer's note to its dealers. It is not part of this recall.