WenmarOpen by Wenmar Pro

Service bulletins for the 2005 Volkswagen Beetle

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

259 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Bulletins, newest first
9414022023-07-24. Service bulletin. EXTERIOR LIGHTING. Exterior Lights, Moisture Accumulation
9414012023-07-24. Service bulletin. EXTERIOR LIGHTING. Exterior Lights, Moisture Accumulation
9113132023-07-24. Service bulletin. EQUIPMENT:ELECTRICAL:ANTENNA. Antenna Diagnosis Overview
9113092023-07-24. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. Satellite Radio Overview
8714092023-07-24. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM. Air Conditioning, Cleaning of the Refrigerant Circuit (U.S.Only)
8714022023-07-24. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM. HVAC, Unpleasant Odor
8714012023-07-24. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM. HVAC, Unpleasant Odor
8713012023-07-24. Service bulletin. VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM. HVAC, Unpleasant Odor
TT5713042023-07-17. Service bulletin. ELECTRICAL SYSTEM:IGNITION:ANTI-THEFT:IMMOBILIZER/PROXIMITY:KEY/SENDER; ELECTRICAL SYSTEM. When adapting keys using ODIS, an error message may be displayed once the test plan directs to cycle the key off. If error is displayed, this does not necessarily indicate key adaptation has failed. If the immobilizer light turns off (instead of flashes) when key is switched on, key adaptation is in process. Continue to cycle remaining keys through ignition and then wait 2 minutes with the key off after adapting the last key. After 2 minutes have elapsed, evaluate vehicle operation with all keys, waiting 2 minutes with ignition off between each key.
TT5713022023-07-17. Service bulletin. ELECTRICAL SYSTEM:IGNITION:ANTI-THEFT:IMMOBILIZER/PROXIMITY:KEY/SENDER. If key blade is found to stick or bind when opening or closing, check position of roll pin that secures key blade to mechanism. If roll pin is sticking out on either side (as shown below), do not replace key. Instead, use appropriate sized punch and hammer to drive in the roll pin so that it is flush with edge of mechanism.
Warranty2023-07-17. Service bulletin. EQUIPMENT. Volkswagen Warranty Policies and Procedures ? April 2014
VWS13032023-07-17. Service bulletin. ENGINE; EQUIPMENT. In SAGA, the time units for the Volkswagen DoubleCheck labor operation were reduced in error from 50 time units to 30 time units during the system update posted on July 4th.
UpdateB2023-07-17. Service bulletin. COMMUNICATION:MANUFACTURER TELEMATICS. Quick Reference Update Guide
UpdateA2023-07-17. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. Quick Reference Update Guide
TT5710112023-07-10. Service bulletin. ELECTRICAL SYSTEM; LATCHES/LOCKS/LINKAGES:DOORS:LOCK; ELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM; STRUCTURE. If a comfort or body control module is replaced during normal diagnosis, make sure the factory mode has been switched OFF. This can be accomplished by selecting the test plan through GFF or through Vehicle Self Diagnosis in adaptation channel 99.
TT5014012023-07-10. Service bulletin. WHEELS; TIRES. The use of tire dressing gives your tires that shiny finish that completes the image of a clean (new) vehicle. There are many different tire dressing products available. When choosing a product please pay close attention to its contents. Always use a water based product.
TT201301a2023-07-10. Service bulletin. UNKNOWN OR OTHER; ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM); FUEL SYSTEM, OTHER. To clear static ECM fault P1250 ?Fuel Level Too Low?, add fuel to vehicle and complete a road test of at least 10 miles. Simply adding fuel without completing a road test may not allow fault to clear.
TT2013012023-07-10. Service bulletin. FUEL SYSTEM, OTHER; ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM); UNKNOWN OR OTHER. To clear static ECM fault P1250 ?Fuel Level Too Low?, add fuel to vehicle and complete a road test of at least 10 miles. Simply adding fuel without completing a road test may not allow fault to clear.
TT2009062023-07-10. Service bulletin. FUEL SYSTEM, GASOLINE; ENGINE AND ENGINE COOLING:ENGINE:DIESEL; FUEL SYSTEM, DIESEL; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER. Use the diagram below to test the N75 Solenoid Valve in the event of a turbocharger fault code such as P0299 or P0234. This applies to Mechanical Injection Style Diesel Engines, Pumpe Duse Style Diesel Engines and the new Common Rail Style Diesel Engines.
TT0014032023-07-10. Service bulletin. EQUIPMENT; EQUIPMENT:ELECTRICAL:INFOTAINMENT:BLUETOOTH/WIFI; ELECTRICAL SYSTEM. When performing SVM updates, the scan tool should be hardwired to the vehicle and the Bluetooth physically turned off. A hard wired internet connection is also recommended.
TT001304A2023-07-10. Service bulletin. EQUIPMENT. If a needed service part is on back order, upgrade the daily order to a red order and check the ?Car Down? box to escalate the order. If parts assistance is needed, please call 800-767-6552 to speak with a VWGoA Parts Specialist.
TT0013042023-07-10. Service bulletin. EQUIPMENT. If a needed service part is on back order, upgrade the daily order to a red order and check the ?Car Down? box to escalate the order. If parts assistance is needed, please call 800-767-6552 to speak with a VWGoA Parts Specialist.
TT3706062023-07-05. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). 09A Transmission -- Replacing Transmission
TT3214012023-07-05. Service bulletin. POWER TRAIN. Incorrect torque converter or flywheel/flexplate installation can result in transmission damage. When installing an engine, flywheel or transmission, please follow the installation procedures outlined in ELSA. For the flywheel/flexplate, please be certain the correct shim is installed between it and the crankshaft (reference VWIQ120). When installing a torque converter, press the torque converter hub through the seal as far as the first stop. Turn the torque converter while pushing toward the transmission using light force, until the cut outs in the torque converter hub lock into the pump wheel plate. The torque converter slides in. The torque converter is installed correctly if it is easy to turn by hand and if it fits evenly in the transmission bell housing. Additionally, it should spin freely when the transmission bell housing bolts are torqued to the engine block, prior to installation of the flywheel to converter bolts (reference VWIQ121).
TT2713012023-07-05. Service bulletin. ELECTRICAL SYSTEM. When diagnosing a generator charging concern, it is recommended to verify operation of the one way clutch located in the generator pulley (if equipped) before replacing generator assembly. To check the one way clutch, remove the belt from the generator pulley and use a trim removal tool to hold fan blades inside generator, as shown below. When attempting to turn pulley by hand with fan blades held, pulley should spin freely in only one direction. If pulley spins freely in both directions, the one way clutch has failed and should be replaced before continuing diagnosis.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.