Recalls that may apply to the 2009 Toyota Corolla
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
By component
| 19V741000 | 2019-10-17. AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE; AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE. Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2010-2016 4Runner, 2003-2006 Tundra, 2003-2013 Corolla, 2009-2010 Corolla Matrix, 2004-2005 RAV4, 2002-2007 Sequoia, 2011-2013 Sienna, 2008-2012 Scion xB, 2008-2009 Lexus IS-F, 2007-2012 Yaris and Lexus ES350, 2010-2017 Lexus GX460, 2002-2010 Lexus SC430, 2006-2012 Lexus IS250 and IS350 and 2010-2015 Lexus IS250C and IS350C vehicles. These vehicles had their driver or passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling. Built 2001-12-28 to 2013-07-12. |
|---|---|
| 18V024000 | 2018-01-09. AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE. Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2013 Scion xB, Toyota Corolla, Corolla Matrix, Sienna, 4Runner, Lexus IS250, IS350, IS250C, IS350C, IS-F, and GX460 vehicles sold, ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP (Saipan), and the U.S. VI or "Zone A." Toyota is also recalling certain 2010 Scion xB, Toyota Corolla, Corolla Matrix, Yaris, 4Runner, Lexus IS250, IS350, IS250C, IS350C, ES350, IS-F, GX460, and Pontiac Vibe vehicles sold, ever registered, in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." Toyota is also recalling certain 2009 Scion xB, Toyota Corolla, Corolla Matrix, Yaris, Lexus IS250, IS350, ES350, IS-F, and Pontiac Vibe vehicles ever registered in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. Built 2007-11-23 to 2010-12-06. |
| 17V006000 | 2017-01-09. AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE. Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2012 Toyota 4Runner, Corolla, Corolla Matrix, Sienna, Yaris, Scion xB, Lexus ES350, GX460, IS-F, IS250, IS350, IS250C, IS350C, and Lexus LFA vehicles originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Toyota is recalling certain 2009 Toyota Corolla, Corolla Matrix, Yaris, Yaris HB, Scion xB, Pontiac Vibe, Lexus, ES350, IS250, IS350, and IS-F vehicles originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Additionally, unless included in "Zone A" or "Zone B" above, Toyota is recalling certain 2006-2008 Lexus IS250 and IS350, 2007-2008 Lexus ES350, Toyota Yaris, Yaris HB, and 2008 Lexus IS-F and Scion xB vehicles originally sold, or ever registered in Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin and Wyoming. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. Built 2007-11-23 to 2009-03-03. |
| 16V396000 | 2016-06-02. SEATS:FRONT ASSEMBLY:SEAT HEATER/COOLER. Southeast Toyota Distributors, LLC (SET) is recalling certain 2005-2011 4Runner, Highlander, Sequoia, and Sienna, 2005-2010 Avalon and Tundra, 2006-2008 Camry Solara, 2006-2010 Highlander hybrid, 2006-2011 Rav4 and Tacoma, 2007-2010 FJ Cruiser, 2007-2011 Camry hybrid, 2009-2010 Venza, 2010-2012 Prius, 1988-1990 and 2005-2010 Camry, and 1989 and 2009-2010 Corolla vehicles equipped with aftermarket accessory seat heaters with a copper strand heating element. The electrical wiring in the seat heaters may be damaged when the seat cushion is compressed. Built 1987-12-05 to 2012-01-27. |
| 16V340000 | 2016-05-23. AIR BAGS:FRONTAL:PASSENGER SIDE:INFLATOR MODULE. Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2008-2011 Scion xB and Lexus IS F, 2009-2011 Toyota Corolla and Corolla Matrix, 2006-2011 Toyota Yaris, Lexus IS250 and Lexus IS350, 2010-2011 Toyota 4Runner, Lexus IS250C, Lexus IS350C and Lexus GX460, 2011 Sienna, 2007-2011 Lexus ES350, and 2009-2010 Pontiac Vibe vehicles, originally sold, or ever registered, in Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands, or "Zone A." Additionally, unless included in "Zone A" above, Toyota is recalling certain model year 2008 Scion xB and Lexus IS F, 2007-2008 Toyota Yaris, 2006-2008 Lexus IS250 and Lexus IS350 and 2007-2008 Lexus ES350 vehicles, originally sold, or ever registered, in Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia, or "Zone B." Vehicles of these model years and models that were not originally sold or ever registered in either Zones A or B are not subject to this safety recall. These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules, and used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the front air bags, these inflators may rupture due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling. Built 2007-07-31 to 2011-12-20. |
| 15V689000 | 2015-10-22. VISIBILITY:POWER WINDOW DEVICES AND CONTROLS. Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window Master Switch (PWMS), grease lubricant may have been inconsistently applied to the sliding electrical contacts. Built 2008-08-01 to 2010-12-31. |
| 14V168000 | 2014-04-09. AIR BAGS:FRONTAL:DRIVER SIDE:INFLATOR MODULE. Toyota is recalling certain model year 2006-2008 RAV4, 2006-2010 Yaris, 2008-2010 Highlander, and 2009-2010 Tacoma, Corolla, Corolla Matrix and General Motors Pontiac Vibe vehicles. In the affected vehicles, the steering column assembly contains electrical connections to the driver's airbag module housed in a spiral cable assembly, which includes a Flexible Flat Cable (FFC). Due to the shape and location of the FFC's retainer, the FFC could become damaged when the steering wheel is turned. Built 2007-07-31 to 2010-07-07. |
| 12V491000 | 2012-10-10. VISIBILITY:POWER WINDOW DEVICES AND CONTROLS. Toyota is recalling certain model year 2007-2009 Camry, Camry Hybrid, RAV4, Corolla, Corolla Matrix, Tundra, Sequoia, Highlander, Highlander Hybrid, Yaris, Scion xB, Scion xD and Pontiac Vibe vehicles. The power window master switch assemblies in some of these vehicles were built using a less precise process for lubricating the internal components of the switch assemblies. Irregularities in this lubrication process may cause the power window master switch assemblies to malfunction and overheat. Built 2007-11-23 to 2008-12-18. |
| 10V036000 | 2010-02-03. EQUIPMENT:OTHER:LABELS. SOUTHEAST TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2011 PASSENGER VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS. |
| 10V035000 | 2010-02-03. EQUIPMENT:OTHER:LABELS. GULF STATES TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2010 VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD BETWEEN SEPTEMBER 1, 2005 AND JUNE 2, 2008 WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS. |
| 10V023000 | 2010-01-27. VEHICLE SPEED CONTROL:ACCELERATOR PEDAL. TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008-2010 HIGHLANDER, MODEL YEAR 2009-2010 COROLLA, VENZA AND MATRIX PASSENGER VEHICLES. THE ACCELERATOR PEDAL CAN GET STUCK IN THE WIDE OPEN POSITION DUE TO ITS BEING TRAPPED BY AN UNSECURED OR INCOMPATIBLE DRIVER'S FLOOR MAT. THIS RECALL IS AN EXPANSION OF A CAMPAIGN OF 3.8 MILLION OTHER TOYOTA VEHICLES ANNOUNCED IN 2009 FOR THE SAME ISSUE (SEE 09V-388). |
| 10V017000 | 2010-01-21. VEHICLE SPEED CONTROL:ACCELERATOR PEDAL. TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2010 AVALON, MODEL YEAR 2007-2010 CAMRY, MODEL YEAR 2009-2010 COROLLA, COROLLA MATRIX, RAV4, MODEL YEAR 2010 HIGHLANDER, MODEL YEAR 2008-2010 SEQUOIA, AND MODEL YEAR 2007-2010 TUNDRA VEHICLES. DUE TO THE MANNER IN WHICH THE FRICTION LEVER INTERACTS WITH THE SLIDING SURFACE OF THE ACCELERATOR PEDAL INSIDE THE PEDAL SENSOR ASSEMBLY, THE SLIDING SURFACE OF THE LEVER MAY BECOME SMOOTH DURING VEHICLE OPERATION. IN THIS CONDITION, IF CONDENSATION OCCURS ON THE SURFACE, AS MAY OCCUR FROM HEATER OPERATION (WITHOUT A/C) WHEN THE PEDAL ASSEMBLY IS COLD, THE FRICTION WHEN THE ACCELERATOR PEDAL IS OPERATED MAY INCREASE, WHICH MAY RESULT IN THE ACCELERATOR PEDAL BECOMING HARDER TO DEPRESS, SLOWER TO RETURN, OR, IN THE WORST CASE, MECHANICALLY STUCK IN A PARTIALLY DEPRESSED POSITION. Built 2008-01-02 to 2010-01-22. |
| 09V338000 | 2009-08-27. SERVICE BRAKES, HYDRAULIC:POWER ASSIST:VACUUM. TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008-2009 SCION XD AND MY 2009-2010 COROLLA, AND COROLLA MATRIX VEHICLES EQUIPPED WITH 1.8L ENGINE AND ORIGINALLY SOLD IN OR CURRENTLY REGISTERED IN THE STATES OF ALASKA, COLORADO, IDAHO, ILLINOIS, IOWA, KANSAS, MAINE, MICHIGAN, MINNESOTA, MONTANA, NEBRASKA, NEVADA, NEW HAMPSHIRE, NEW YORK, NORTH DAKOTA, SOUTH DAKOTA, VERMONT, WISCONSIN, AND WYOMING. WHEN DRIVING UNDER CERTAIN UNIQUE CONDITIONS IN EXTREMELY LOW AMBIENT TEMPERATURES, THE INTAKE MANIFOLD SUCTION PORT FOR THE BRAKE VACUUM CAN BECOME BLOCKED DUE TO THE FREEZING OF CONDENSATION RESULTING FROM POSITIVE CRANKCASE VENTILATION. Built 2008-01-02 to 2007-11-26. |
| 2021723 | 2021-11-24. Electrical. Issue: This recall is for certain block heater kits installed on certain vehicles or sold as accessories at Toyota or Lexus dealerships. On certain vehicles, the engine block heater cable may not have enough heat protection and could be damaged by high temperatures. If this happens, the cable could short circuit while plugged in, and cause the wiring to overheat or melt. Note: This recall only affects the following block heater/cord part numbers: C014003034 PK5A408J09 PU14000904 C014003151 PK5A408J13 PU14000905 C014000885 PK5A489J11 PU14000907 C014000888 PK5A489J22 PU14000909 C014000907 PK5A410H00 PU14000911 C014100904 PU14000900 PU14000913 C014100907 PU14000901 PU14003571 C014100911 PU14000902 PK5A489J14 PK5A408J05 PU14000903 Safety Risk: Engine block heater wiring that overheats or melts could create the risk of a fire. Corrective Actions: Toyota recommends that you should stop using the engine block heater immediately. Toyota will notify owners by mail and instruct you to take your vehicle to a dealer to disable the engine block heater. For some vehicles, the corrective actions for this recall are under development. For others, a new engine block heater cannot be installed, and the owner will receive a refund of the purchase price of the engine block heater. |
|---|---|
| 2018014 | 2018-01-09. Airbag. On certain vehicles, long-term exposure to high absolute humidity and temperature, combined with high temperature cycling, could eventually degrade the propellant contained in the passenger frontal airbag. This could cause the airbag to deploy with more force than normal. As a result, if the vehicle were involved in a collision that warrants airbag deployment, fragments could be propelled toward vehicle occupants, and the airbag assembly could be damaged, preventing proper function. These issues could increase the risk of injury. Correction: Depending on the vehicle model, dealers will either replace the passenger frontal airbag inflator, or replace the airbag assembly. Note: Canadian climate results in the propellant degrading slowly. The recall is being conducted as a precaution to address future risk, and is expected to replace airbag inflators before their function would be affected. |
| 2015493 | 2015-10-21. Electrical. On certain vehicles, inconsistent application of grease during the manufacturing process could cause the driver's side power window master switch to stick or become inoperative due to electrical contact point wear. This could cause debris to accumulate between the contact points, potentially resulting in an electrical short circuit. If a short circuit occurs, the switch assembly may overheat, produce smoke, melt and/or potentially lead to a fire causing injury and/or property damage. Correction: Dealers will inspect the driver's power window master switch and apply a specialized grease that inhibits heat build-up, or replace the power window master switch circuit board, as necessary. Note: This is an expansion of recall 2012-338. |
| 2014124 | 2014-04-09. Airbag. On certain vehicles, electrical circuitry in the steering wheel assembly may become damaged. As a result, the driver's airbag may not function as intended, causing the instrument panel airbag warning lamp to illuminate. Failure of the driver's airbag to deploy during a crash (where deployment is warranted) could increase the risk of injury to the seat occupant. Correction: Dealers will replace the spiral cable assembly. |
| 2013317 | 2013-09-20. Structure. On certain vehicles, the trunk lid may begin to close after it has been opened. Contributing factors may include the trunk lid being in the partially open position, windy conditions, the vehicle being parked on an incline, or weight (such as snow or ice) acting on the trunk lid. As a result, interaction could occur between a person and the trunk lid, which could lead to minor injury. Correction: Owners who are dissatisfied with the performance of their vehicle’s trunk lid may have the trunk springs replaced under special warranty coverage. |
| 2012338 | 2012-10-10. Electrical. On certain vehicles, due to improperly applied grease, the driver's side power window master switch could stick or become inoperative. If attempts are made to lubricate the switch, the switch assembly could overheat and melt. A melting switch may produce smoke and potentially lead to a fire causing property damage and/or personal injury. Correction: Dealers will inspect the driver's power window master switch and apply a specialized grease that inhibits heat build-up, or replace the power window master switch circuit board, as necessary. |
| 2010012 | 2010-01-22. Other. On certain vehicles, accelerator pedal movement may become rough, slow to return, or the pedal may stick in a depressed position. This could result in a loss of throttle control and a vehicle crash, causing property damage, personal injury or death. Correction: Dealers will install a steel reinforcement bar to the accelerator pedal assembly. With this reinforcement in place, the excess friction that can cause the pedal to stick is eliminated. |
| 2009290 | 2009-10-07. Other. On certain vehicles, the accelerator pedal may become stuck in the wide open position due to an unsecured or incompatible driver's floor mat. A stuck open accelerator pedal may result in very high vehicle speeds and make it difficult to stop the vehicle, which could cause a crash, serious injury or death. Correction: Dealers will reconfigure the shape of the accelerator pedal. Certain models will also have the shape of the floor underneath the accelerator pedal modified and/or a brake override system installed. |
| 2009251 | 2009-08-26. Brakes. On certain vehicles, when driven in extremely low ambient temperatures, the intake manifold suction port for the brake vacuum can become blocked due to the freezing of condensation emanating from Positive Crankcase Ventilation (PCV). Should the suction port become blocked, vacuum assist to the brakes would be insufficient and the increased pedal pressure required could lead to an increase in vehicle stopping distance. Extended stopping distances may result in a vehicle crash causing property damage, personal injury or death. Correction: Dealers will install a newly designed intake air connector which will relocate the brake system vacuum port. |
A campaign lists a year, a make and a model, and often only some of the vehicles built. A list with nothing on it is not a clearance either. The lookups below check one VIN.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.