Service bulletins for the 2016 Subaru WRX
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
429 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Engine are shown. Show all
| 02-172-18R | 2018-06-11. Service bulletin. ENGINE. This bulletin provides details regarding a new oil filler tube o-ring developed to address engine oil seepage concerns. This seepage may accumulate along the bottom sealing surface of the rocker cover. The new o-ring utilizes material which has an increased resistance to engine heat. |
|---|---|
| 02-170-17 | 2018-04-02. Service bulletin. ENGINE AND ENGINE COOLING. This bulletin announces part information for new Active Valve Control System (AVCS) oil control solenoid valves (OCV) which contain a redesigned internal oil seal. The new seal will eliminate potential oil seepage into the wire harness connector portion of the valve. If oil seeps into the connector, over time, the Check Engine lamp may illuminate and set various AVCS-related DTCs. |
| 10-84-16R | 2017-10-27. Service bulletin. ENGINE AND ENGINE COOLING; POWER TRAIN:CLUTCH ASSEMBLY; ELECTRICAL SYSTEM. This bulletin announces the availability of a new Air Conditioning compressor / clutch assembly to address customer concerns of the system not operating. Electrical windings located inside the clutch assembly have been changed to eliminate the condition. The service procedure will involve replacement of the A/C compressor and clutch as a complete assembly. |
| 02-168-17 | 2017-09-14. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:BELTS AND ASSOCIATED PULLEYS; ENGINE. This Service Information bulletin announces a material change to the engine accessory drive / v-belt made to address customer concerns of a slipping belt (squeal or chirping) sound. |
| 02-166-17R | 2017-09-14. Service bulletin. ENGINE AND ENGINE COOLING. This bulletin outlines design changes made to the upper oil pan assembly on FA and FB engines used on the models listed above. There have been isolated cases where the sealer used between the upper oil pan and the crankcase has become displaced resulting in engine oil seepage. Revisions made to the upper oil pan casting: * The mating flange thickness of the casting in the area identified as the cause for the seepage has been increased by 5.5mm. (See images provided in the Parts Information section below.) This thickness increase creates the need for a longer bolt to provide proper tightening and retention. * An additional mounting point has been added to the ribbing inside the casting to increase retention of the steel baffle plate and eliminate vibration. |
| 02-166-17 | 2017-08-14. Service bulletin. ENGINE AND ENGINE COOLING. This bulletin outlines design changes made to the upper oil pan assembly on FA and FB engines used on the models listed above. There have been isolated cases where the sealer used between the upper oil pan and the crankcase has become displaced resulting in engine oil seepage. |
| 02-164-16 | 2017-08-14. Service bulletin. ENGINE AND ENGINE COOLING. This Service Information bulletin announces a design change to the internal contact portion of the oil pressure switch to increase durability |
| 02-162-15 | 2017-02-27. Service bulletin. ENGINE. "THIS SERVICE INFORMATION BULLETIN ANNOUNCES A DESIGN CHANGE TO THE OIL PRESSURE SWITCH ASSEMBLY. NICKEL PLATING HAS BEEN APPLIED TO THE INTERNAL SWITCH CONTACTS TO ENHANCE THEIR DURABILITY AND REDUCE THE POSSIBILITY OF POOR CONTACT WHICH COULD AFFECT OPERATION OR CAUSE IMPROPER ILLUMINATION OF THE OIL PRESSURE WARNING LAMP. A SMALL PILOT PORTION WAS ADDED TO THE THREADED AREA ON P.N. 25240KA051 AS SHOWN IN THE ILLUSTRATION BELOW." |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.