Recalls that may apply to the 2000 Saab 9-5
A recall listed here may apply to a vehicle of this year, make and model. Only the manufacturer can say whether it applies to one vehicle: check the VIN with the official lookups.
By component
| 05V399000 | 2005-09-14. ELECTRICAL SYSTEM:IGNITION:MODULE. CERTAIN PASSENGER VEHICLES EQUIPPED WITH B205/B235 4-CYLINDER GASOLINE ENGINES AND B308 6-CYLINDER GASOLINE ENGINES MAY EXPERIENCE OVERHEATING AND BURNOUT OF THE ISOLATED GATED BIPOLAR TRANSISTOR (IGBT) WITHIN THE IGNITION DISCHARGE MODULE (IDM) DUE TO INCREASED SUSCEPTIBILITY TO ELECTRICAL LOADS. Built 1999-06-01 to 2000-06-30. |
|---|---|
| 03V006000 | 2003-01-13. WHEELS:HUB. ON CERTAIN PASSENGER VEHICLES, IF AN OWNER CHANGES THEIR WHEELS/TIRES BETWEEN SUMMER AND WINTER USING A STEEL WHEEL IN THE WINTER AND AN ALLOY WHEEL IN THE SUMMER, IT IS POSSIBLE FOR RUST AND CONTAMINATION TO BUILD UP ON THE WHEEL HUB DURING THE STEEL WHEEL USAGE. IF THIS OCCURS AND THE CONTAMINATION IS NOT REMOVED, IT IS POSSIBLE THAT AFTER THE TIRE CHANGE SERVICE, SOME OF THIS CONTAMINATION COULD FLAKE OR GRIND AWAY RESULTING IN REDUCED CLAMPING FORCE OF THE WHEEL TO THE HUB. OVER SEVERAL SEASONS, IT IS POSSIBLE THAT THIS REDUCED FORCE COULD RESULT IN FRACTURES DEVELOPING IN THE WHEEL BOLTS DUE TO WHEEL TO HUB MOVEMENT. Built 1997-11-26 to 2002-10-10. |
| 01V168000 | 2001-05-18. AIR BAGS. VEHICLE DESCRIPTION: CERTAIN PASSENGER VEHICLES FAIL TO COMPLY WITH REQUIREMENTS OF FMVSS NO. 208, "OCCUPANT CRASH PROTECTION." THE AIR BAG ALERT LABELS MAY NOT BE PERMANENTLY AFFIXED AS REQUIRED BY THIS STANDARD. Built 1999-09-27 to 2000-07-07. |
| 2005271 | 2005-09-20. Electrical. Certain 2000-2002 Saab 9-3 and 9-5 model vehicles equipped with 4-cylinder gasoline engines, and 2001-2003 9-5 models equipped with 6-cylinder gasoline engines may experience overheating and burnout of the Isolated Gated Bipolar Transistor (IGBT) within the Ignition Discharge Module (IDM) due to increased susceptibility to electrical loads. Overheating of the IGBT occurs most often at engine start-up but may also occur while the engine is running. When the IDM fails on a 4-cylinder while it is running, the engine may stall without warning, with no ability to be restarted. When the IDM fails on a 6-cylinder engine while it is running, the driver will initially experience reduced power and rough operation because the engine will only be running on three cylinders. The check engine light will flash. If the driver continues, unburnt fuel in the exhaust can cause thermal damage to the catalytic converter. The engine may stall and not restart. Correction: Dealers will inspect and, if required, replace the IDM. |
|---|---|
| 2005179 | 2005-06-14. Other. Certain vehicles do not comply with the requirements of CMVSS 210. The required markings for the child tether anchorage hooks are missing in the luggage compartment area. Correction: Dealers will install the required adhesive label to the luggage compartment loading floor in the near vicinity of the three anchorage hooks. |
| 2002247 | 2002-12-23. Suspension. On certain vehicles, when changing back and forth between alloy and steel wheels (as for winter tires), rust and other contaminates may build up on the mating surface of the wheel hubs. If this surface is not cleaned between wheel changes, uneven torque forces may cause wheel bolts to fracture. Although this is most likely to happen during wheel change service, it is possible that the bolts may break later while the vehicle is being driven. Correction: Dealer will clean the hub and reinstall the wheel with improved bolts and attached washers that will eliminate the clamping force reduction. |
A campaign lists a year, a make and a model, and often only some of the vehicles built. A list with nothing on it is not a clearance either. The lookups below check one VIN.
Check one vehicle officially
Contains information licensed under the Open Government Licence – Canada.