WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Ram Promaster 2500

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

184 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
18048232023-05-30. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK
S14080003842023-04-17. Service bulletin. ELECTRICAL SYSTEM. Start Stop Charging Warning Lamp Illuminated On, Intelligent Battery Sensor (IBS) State of Charge (SOC) Inaccurate, Battery Charging Message, Presence of IBS related Diagnostic Trouble Codes (DTCs), or Battery Warning Lamp On
S21080001632023-01-17. Service bulletin. ELECTRICAL SYSTEM. No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
S21090000042023-01-17. Service bulletin. ENGINE AND ENGINE COOLING. Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
31001222023-01-09. Service bulletin. STRUCTURE. Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
68105583A2022-12-19. Service bulletin. ENGINE AND ENGINE COOLING; EQUIPMENT. Pentastar Oil Filter Adapter
68141352A2022-12-19. Service bulletin. ENGINE AND ENGINE COOLING. 3.2L - 3.6L Cylinder Head Assy Multiple cylinder head replacement. If cylinder head is replaced on a vehicle more than 1 time for any reason, please call any of the following people.~ First: Ron Dallison ? Cell (248) 292-9510 Ron.dallison@fcagroup.com ~ Second: Joe Lovell - Cell (734) 309-6467 joe.lovell@fcagroup.com~ If a response is not received within 15 mins, then proceed with the necessary repair.~
S22090000042022-12-19. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils.
25001162022-11-21. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, DIESEL. Diagnosing A Urea Module That Is Exposed To Diesel Fuel This bulletin involves discussing what will happen to the rubber material used in the urea pump when exposed to diesel fuel. This unit is sometimes referred to as the Selective Catalyst Reductant (SCR) module or the Adblue Delivery Module (ADM). Units exposed to hydrocarbons have a particular failure mode, the rubber heater unit is crinkled and in some cases the metal heater protrudes through the rubber membrane. The rubber material used in this unit is designed to withstand Diesel Exhaust Fluid (DEF) only. Exposure to fluids that contain hydrocarbons (i.e. diesel fuel) will damage the unit beyond repair. Units returned that exhibit this failure mode will have warranty claims that are rejected. Units that exhibit this failure mode should be considered customer abuse and should not be covered under warranty. Use the Hydroscopic test paper (P/N 223-44-863) available through MoparEssentialTools.com to confirm exposure.
31001222022-10-31. Service bulletin. STRUCTURE. Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
31001222022-10-31. Service bulletin. STRUCTURE:INTERIOR PANELS:DOOR; STRUCTURE; UNKNOWN OR OTHER. Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components.
051520292022-10-17. Service bulletin. VISIBILITY/WIPER. Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you.
683328102022-10-17. Service bulletin. ENGINE AND ENGINE COOLING. Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar® Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 N·m [21 ft. lbs.].
S21080001632022-09-26. Service bulletin. ELECTRICAL SYSTEM. No Start, Cannot Complete Module Replace, Proxi Or Module Proxi Configuration
S21090000042022-09-26. Service bulletin. ENGINE AND ENGINE COOLING. Issue involves overheating, running hot, coolant leaks and related symptoms after a Mopar replacement engine has been installed in the vehicle.
90043862022-09-26. Service bulletin. ELECTRICAL SYSTEM:WIRING. WIRING, Body Before replacing this harness, please contact FCA Redacted Content to see if a repair kit is available for your application. If no response in 15 minutes, proceed with repair. Please email pictures of harness defects to FCA Redacted Content
S16080002262022-09-26. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Battery Tester Warranty Code Procedures, Midtronics Charger Update Process
S160800022612022-09-26. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. Battery Tester Warranty Code Procedures, Medtronic Update Process
S18210000012022-09-26. Service bulletin. POWER TRAIN. Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
90040092022-09-26. Service bulletin. POWER TRAIN. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
31005192022-09-15. Service bulletin. STRUCTURE. Use of Aftermarket Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of aftermarket parts.
31003192022-09-15. Service bulletin. STRUCTURE. Use of Salvage/Recycled Parts This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the use of recycled or salvage parts.
31004192022-09-15. Service bulletin. VISIBILITY. Authentic Mopar® Glass Replacement This bulletin involves discussing FCA US LLC position with regard to collision repair industry awareness regarding the recommended usage of Authentic Mopar® Glass.
31006192022-09-15. Service bulletin. STRUCTURE; EQUIPMENT. Repair Parts Used For Structural Repairs This bulletin involves discussing FCA US LLC position with regard to structural repair parts usage.
18089192022-09-15. Service bulletin. ENGINE AND ENGINE COOLING. wiTECH Small Leak Verification Test (SLVT) - P0456-EVAP SYSTEM SMALL LEAK

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.