Service bulletins for the 2014 Ram 5500
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
355 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
Only bulletins with component: Electrical system are shown. Show all
| 0811015 | 2022-07-05. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT; STRUCTURE. This bulletin involves configuring the Body Control Module (BCM). |
|---|---|
| 0810815 | 2022-07-05. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. This bulletin involves reprogramming the Vehicle System Interface Module (VSIM) with the |
| 9004470 | 2022-06-27. Service bulletin. ELECTRICAL SYSTEM:WIRING; TRAILER HITCHES. CONNECTOR/WIRING, Trailer Tow If the connector or wiring is physically damaged, burned, melted or corroded, prior to replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content |
| 0900122 REVA | 2022-05-31. Service bulletin. ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER; EXTERIOR LIGHTING. Cummins 6.7L Turbocharger Actuator - X93 Warranty Extension This bulletin involves replacing the turbocharger actuator with an updated actuator. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technicianmay find that one or more of the following Diagnostic Trouble Codes (DTCs) have been set: U010C - Lost Communication With Turbocharger/Supercharger Control Module. P003A - Turbocharger Boost Control Module Position Exceeded Learning Limit. P00AF - Turbocharger Boost Control Module Performance. P0046 - Turbocharger Boost Control Circuit Performance. P0234 - Turbocharger Overboost Condition. |
| 9003600 | 2021-05-03. Service bulletin. ELECTRICAL SYSTEM:WIRING:CONNECTORS/PLUGS:ACCESORY POWER OUTLET/JACK/PORT/USB/SAE/CIGARETTE LIGHTER. USB Charging port. |
| DOR-E8D6V-08 | 2020-08-24. Service bulletin. ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL; TRAILER HITCHES. These SKUs are Trailer Brake Control Modules. The customer communication requested return of unsold inventory due to an internal software issue. The internal software issue leads to a fault code for lack of communication with the Trailer Brake Controller. This will cause the part to be replaced because because module installation cannot be completed due to this lack of electronic communication. |
| DOR-E4E8S-08 | 2020-08-24. Service bulletin. ELECTRICAL SYSTEM: INTEGRATED TRAILER BRAKE CONTROL. These SKUs are Trailer Brake Control Modules. The customer communication requested return of unsold inventory due to an internal software issue. The internal software issue leads to a fault code for lack of communication with the Trailer Brake Controller. This will cause the part to be replaced because because module installation cannot be completed due to this lack of electronic communication. |
| 18-042-20 | 2020-06-22. Service bulletin. FUEL SYSTEM, DIESEL; ELECTRICAL SYSTEM; EQUIPMENT; ENGINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:There will be a choice between two calibrations. One for vehicles that utilize an ammonia sensor and one for vehicles that have had the ammonia sensor removed. Be sure to select the correct software based on vehicle configuration.Improvements to prevent or reduce MIL illumination when no defect is present for:P2201 - Aftertreatment Nox Sensor Circuit Performance - Bank 1 Sensor 1(Ammonia delete systems only). P229F - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2. P20EE - SCR NOx Catalyst Efficiency Below Threshold - Bank 1(New Improvements for ammonia delete systems only). P202E - Diesel Exhaust Fluid (DEF) Reductant Injector Performance(New Improvements for ammonia delete systems only). P218F - Reductant No Flow Detected. P1C55 - NOx Sensor Intermittent - Bank 1 Sensor 1. U0001 - CAN C Bus. P229E - NOx Sensor Circuit - Bank 1 Sensor 2(Non-ammonia delete systems only). U059F - Invalid Data Received From NOx Sensor "B"(Non-ammonia delete systems only). P22A7 - NOx Sensor Heater Circuit Performance - Bank 1 Sensor 2(Non-ammonia delete systems only). P2459 - Diesel Particulate Filter Regeneration Too Frequent. P242F - Diesel Particulate Filter Restriction - Ash Accumulation. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. U110E - Lost Ambient Temperature Message. U3017 - Control Module Timer/Clock Performance. P0087 - Fuel Rail Pressure Too Low. P0544 - Exhaust Gas Temperature Sensor Circuit - Sensor 1/1. P2281 - Air Leak Between MAF And Throttle Body. |
| 08-049-20 | 2020-05-26. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. Charging System, Battery Diagnostic Tools and Warranty This information only bulletin discusses using the correct test equipment for testing batteries and charging systems, and also warranty reimbursement when battery replacements are necessary. |
| 54638 | 2019-07-15. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. ASH RECEIVER - INSTRUMENT PANEL |
| 08-006-15 REV A | 2019-05-20. Service bulletin. ELECTRICAL SYSTEM. Flash: Incorrect Language Displayed In The Cluster And Odometer Line Disappears This bulletin involves reprogramming the Instrument Panel Cluster (IPC) with updated software. ? Customer may report that the odometer line disappears sometimes and comes back with an ignition cycle or changing cluster screens. ? The customer may notice when trying to switch the language from English to Spanish/French, only the radio will display the correct language. The cluster will still display English. |
| 08-111-15 | 2019-05-20. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. RA1 Radio Enhancements This bulletin involves updating the software on the RA1 Radio. A customer may experience, one or more of the following conditions: ? Radio may reset, turn itself off and then back on again. All Symptom Listed Below Are For 2013 Vehicles Only: ? Radio may be muted. Any of DTCs B1400-92-Front Left Audio Speaker Output - Performance Incorrect Operation and/or B1404-92- Front Right Audio Speaker Output - Performance Incorrect Operation and/or B1408-92-Rear Left Audio Speaker Output - Performance Incorrect Operation and/or B140C-92-Rear Right Audio Speaker Output - Performance Incorrect Operation, maybe active or stored. ? Radio display screen may turn off. ? Radio will stay on after the vehicle is turned off with remote. (Applies to vehicle with Mopar remote start add on package only). ? Radio will stay on for 20 minutes after ignition is turned off and the only way to turn off the radio is by pressing the power button on the radio. Software was updated to have the radio shut off based on the cluster accessory delay setting. |
| 08-110-15 | 2019-05-20. Service bulletin. ELECTRICAL SYSTEM. LED Lamp Configuration Update This bulletin involves configuring the Body Control Module (BCM). The customer may describe LED Turn Signals do not properly display. |
| 08-108-15 | 2019-05-20. Service bulletin. ELECTRICAL SYSTEM. Vehicle System Interface Module Unresponsive This bulletin involves reprogramming the Vehicle System Interface Module (VSIM) with the latest available software. Customers may notice uplift components connected to the VSIM inoperative at times. This is caused by a condition where as the VSIM locks up and becomes unresponsive. No DTCs will be reported for loss of communication between the VSIM and Central Body Controller (CBC). This can be corrected by updating the VSIM with the latest available software. SYMPTOM ONLY FOR 2013 DD AND DP with Power Take Off Prep (Sales Code LBN) Customers may experience after 30 minutes of operation the PTO may shut off. The PTO will start working again after the ignition is cycled. |
| 18-002-15 REV A | 2019-05-20. Service bulletin. ENGINE; ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN. Flash: Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with updated software. During normal diagnostics a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) present: ? P3426 - Cylinder 4 Deactivation Control Performance. ? P3402 - Cylinder 1 Deactivation Control Performance. ? P3442 - Cylinder 6 Deactivation Control Performance. ? P3450 - Cylinder 7 Deactivation Control Performance. ? U0140 - Lost Communication With Body Control Module. (Attempting to clear this DTC will be unsuccessful.) ? P030X - Cylinder X Misfire Detected. ? P0300 - Multiple Cylinder Misfire Detected. Additionally the following enhancements have been implemented: ? Improved Cruise Control Acceleration mode. ? Improved Multi Displacement System operation. 6-Speed Automatic 66RFE transmission (Sales Code DFP). ? Multi Displacement System function improved while in stationary mode. 6-Speed Auto Aisin AS66RC transmission (Sales Code DF3). ? Potential small improvement in fuel economy at higher altitudes. ? Potential improvement in high altitude engine idle RPM stability. |
| 18-042-15 | 2019-05-20. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN; EQUIPMENT; ENGINE. Flash: 6.4L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Powertrain Control Module (PCM) with new software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the Technician may find one or more of the following Diagnostic Trouble Codes (DTCs) have been set: ? P0300 - Multiple Cylinder Misfire, cold Idle misfire (DJ,D2 or DD vehicles only). ? P030X - Cylinder Misfire (any cylinder) (Additional improvements over the last software update). ? P04D1 - Cooled EGR Temperature Sensor Circuit High. ? P04D0 - Cooled EGR Temperature Sensor Circuit Low. ? P2504 - Charging System Output High. ? P0441 - Evap Purge System Performance. ? P2066 - Fuel Level Sensor 2 Performance. ? P0401 - EGR System Performance (DJ/D2 vehicles only). ? P2096 - Downstream Fuel Trim System 1 Lean (DD/DP vehicles only). ? P2098 - Downstream Fuel Trim System 2 Lean (DD/DP vehicles only). ? P0740 - TCC Out of Range (DD vehicles equipped with a DFP automatic transmission). Customers may also experience any of the following conditions: ? Slightly elevated idle speed noticed during engine warm-up when in Reverse or Drive and when operating in cold ambient temperatures. ? PTO mobile mode cancels or deactivates when vehicle comes to a stop (DD/DP vehicles only). ? Engine cycles in and out of MDS mode too often when operating in PTO stationary mode (DD/DP vehicles only). ? PTO stationary mode cancels or deactivates when PTO up-fit equipment loads fluctuate (DD/DP vehicles only) The following powertrain system improvements/enhancements are also included in this software release: ? Improve Idle at high altitudes (DJ,D2 or DD vehicles only). ? Spark knock on vehicle with low octane fuel (DJ,D2 or DD vehicles only). ? Operator idle speed control enhancements. ? Raise 4x4 low range minimum engine speed from 725 to 800 RPM. ? Raise minimum engine speed to allow MDS activa |
| 56041380A | 2018-11-26. Service bulletin. ELECTRICAL SYSTEM:12V/24V/48V BATTERY. Battery Please call Bob Horn at cell (248) 231-3315 prior to replacing any battery. Please identify battery with the last 8 VIN digits along with the 15 digit Medtronic code from the GR-8 tester. If no response in 15 minutes, continue with the repair. Battery needs to be held and not turned in for core charges. |
| 08-028-16 | 2018-06-25. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); ELECTRICAL SYSTEM:SOFTWARE. RE2 RE6 RB5 RB6 Radio Software Enhancements This bulletin involves updating the radio software and navigation if equipped. A customer may experience one or more of the following conditions: · Radio display screen will lock up and reset intermittently. · Incorrect routing directions to fuel stations when using Travel Link. · Unable to turn on heated seats; icon is greyed out. · Navigation screen goes blank. · Navigation system freezes/locks up. · Vehicles with Mopar special edition radio will update radio?s splash screen. · Navigation icon shows the vehicle going backward when it?s moving forward. |
| Z5091195A$ | 2018-06-11. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT; EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; EQUIPMENT:ELECTRICAL. RES / RHA / REB radio that supports Bluetooth and Hands-Free For issues with Bluetooth, Hands-Free Calling, and/or Voice Commands, DO NOT replace the radio. Diagnose the Hands-Free Module system (also called the Telematics Module). The Telematics Module (and associated components) is the system responsible for these features. A power cycle may be required for the hands-free module for proper diagnosis.~ Please reference; 8T - Navigation/Telecommunication Diagnosis and Testing (DIAGNOSIS AND TESTING - HANDS FREE PHONE) |
| 18-023-16 | 2018-06-11. Service bulletin. EXTERIOR LIGHTING; ELECTRICAL SYSTEM. Flash: 2.4L Powertrain Diagnostic and System Improvements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination or one or more of the following conditions. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: |
| 17161 | 2018-06-11. Service bulletin. ELECTRICAL SYSTEM:IGNITION; EQUIPMENT; ELECTRICAL SYSTEM:IGNITION:SWITCH. You have been identified as either having stock, or have stock in transit to your dealership. Please return suspect stock of part number 04685719AI. See attachments for identifying suspect stock. Please return suspect parts back to your facing depot using Return Code 02, before 11 July, 2016. Return any open orders in process too. Direct all questions via email to mopardmail@fcagroup.com. |
| 30657 | 2018-06-11. Service bulletin. ELECTRICAL SYSTEM. R4801865AC Alternator Assy - 220 Amp You have been identified as either having stock, or have stock in transit to your dealership. Please return all stock of part number R4801865AC. Replacement is part number 04801865AE which is in stock and available. Please return suspect parts back to your facing depot using Return Code 02, before 04 April, 2017. |
| 14-001-14 REV. B | 2018-06-11. Service bulletin. FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM:SOFTWARE. Fuel Gelling in Cold Ambient Temperatures This bulletin involves reconfiguring the Body Control Module (BCM). Some customers may experience a Malfunction Indicator Lamp (MIL) due to fuel related Diagnostic Trouble Code (DTC) and/or may have a hard or no start condition due to fuel gelling in cold ambient temperatures (20°F or -7°C) or below. DTCs, such as P0087, P0191 or P026B (or other DTCs) may have been set.frame mounted fuel filter heater not to function. The condition is due to a configuration setting in the Body Control Module (BCM). |
| 18-002-14 REV. A | 2018-06-11. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, GASOLINE. Flash: Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module (ECM/PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo Diesel. Software To Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (MIL) Illumination For The Following Diagnostic Trouble Codes (DTCs). These DTCs Are Currently Tripped As A One Trip Fault And Should Have Been A Two Trip Fault: ? P0201 - P0206 - FUEL INJECTOR X CIRCUIT/OPEN Fault Codes. ? U110E - LOST AMBIENT TEMPERATURE MESSAGE. ? P049D - EGR CONTROL POSITION EXCEEDED LEARNING LIMIT. Improvements To Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (Mil) Illumination For: ? P0087 - FUEL RAIL PRESSURE TOO LOW. ? P0544 - EXHAUST GAS TEMPERATURE SENSOR CIRCUIT - SENSOR 1/1. ? P2281 - AIR LEAK BETWEEN MAF AND THROTTLE BODY. ? P0128 - THERMOSTAT RATIONALITY. In low ambient temperatures. ? U3017 - CONTROL MODULE TIMER/CLOCK PERFORMANCE. ? U1421 - IMPLAUSIBLE IGNITION KEY OFF TIME RECEIVED. ? P202E - (DIESEL EXHAUST FLUID) REDUCTANT INJECTOR PERFORMANCE. ? P20EE - SCR NOx CATALYST EFFICIENCY BELOW THRESHOLD - BANK 1. ? P2002 - DIESEL PARTICULATE FILTER EFFICIENCY BELOW THRESHOLD. ? P0604 - INTERNAL CONTROL MODULE RAM ERROR. This DTC may be caused by enabling the remote throttle feature via the EVIC, and it will be accompanied by a ?service electronic throttle control? message in the EVIC. Other Updates: ? Fuel Filter Minder Calibration Changes ? Cruise control system improvements. ? Improvements in exhaust brake switch operation. ? Charging system improvements for dual alternator applications. ? Various wiTECH data and system test additions and improvements. ? OBD Template changes for P2453. ? Dual Fuel Tank component update. ? Inducement Timer Reset (Feature enable in wiTech). ? PTO Denied Status Message Update. ? PTO Horn Request sen |
| 68184926A$ | 2018-05-21. Service bulletin. ELECTRICAL SYSTEM. Integrated Center Stack If vehicle is found within 50 mile radius of the Detroit Metro area please hold vehicle and contact:~ Contact one of the following:~ Daniel Acciacca CELL (586) 709-1537~ Michael Savich CELL (248) 214-7270~ Ayed Hadaad CELL (248) 941-8707~ Issue: On a 2015 & 2016MY LA (Challenger), LD(Charger) and LX (300), the Integrated Center Stack (ICS) may experience a lock-up/Inop condition (complete loss of functionality) during any vehicle diagnostic session (reading fault codes, clearing fault codes, reflashing of any module, etc.). If this occurs, do not replace the ICS. The module functionality can be restored if it is reset by disconnecting power to it (by removing fuse, battery disconnect or module connector disconnect).~ |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.