WenmarOpen by Wenmar Pro

Service bulletins for the 2018 Ram 3500

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

444 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Transmission and driveline are shown. Show all

Bulletins, newest first
1023072025-01-06. Service bulletin. POWER TRAIN. GEAR - REACTION SUN
1023872025-01-04. Service bulletin. POWER TRAIN. SEAL - OUTPUT SHAFT
1023892025-01-04. Service bulletin. POWER TRAIN. SEAL - OUTPUT SHAFT
1012322024-11-07. Service bulletin. POWER TRAIN. Plate - Planetary
S18080001522023-04-17. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). CEL (Check Engine Lamp) Illuminates, Recent PCM Replace or Flash Update Performed, Diagnostic Trouble Codes (DTCs) P057B Brake Pedal Position Sensor Circuit Performance, P1572 Brake Pedal Stuck, C0042-54 Brake Pedal Missing Calibration
S1623000028 Rev.2023-02-13. Service bulletin. VEHICLE SPEED CONTROL; BACK OVER PREVENTION; POWER TRAIN; VISIBILITY; PARKING BRAKE. Outside Power Fold Rearview Mirror Noise Or Loose At Pivot. Mirror Contacts Door Window Glass In The Folded Position.
18131222023-01-17. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set: P064F - Unauthorized Software/Calibration Detected. P229F - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2. P207F - Reductant Quality Performance. P249E - Closed Loop Scr Reductant Injection Control At Limit - Flow Too High. P2509 - PCM/PCM Power Input Signal Intermittent. P0128 - Thermostat Rationality. P2201 - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 1. In addition, the following software enhancements are also available:Scan Tool Fan Actuation Test fix. Enabling DTC P208B - Reductant Pump 1 Control Performance. Mass Air Flow (MAF) Sensor Out Of Range (OOR) low calibration. Idle based misfire retune. Abort timer for Selective Catalytic Reduction (SCR) Out NOx Sensor missing change to 70 seconds. Map SCR missing DTC/Fault (P1C54) to tampering inducement. Particulate Matter (PM) Sensor False Fault Improvement. CC inner loop used up faults. Ultrasonic Flow Meter (UFM) test results fix. Engine run state idle unstable software fix. Ability to write Engine Serial Number (ESN) through wiTECH. Add Diesel Exhaust Fluid (DEF)/Reagent type as a readable value in wiTECH. Fan actuation test. SCR missing tuning capability improvement. Smart tampering improvement.
S19080001022022-10-17. Service bulletin. POWER TRAIN. (Rev. A) Power Inverter Load Ratings
1806120REVA2022-10-17. Service bulletin. SERVICE BRAKES; POWER TRAIN; BACK OVER PREVENTION; ELECTRICAL SYSTEM; EXTERIOR LIGHTING; FUEL SYSTEM, GASOLINE. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:P2706 - MS Solenoid Circuit(Sales Code DG7 Only). P0868 - Line Pressure Low. P229F - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2. P207F - Reductant Quality Performance. P2509 - PCM/PCM Power Input Signal Intermittent. P0401 - EGR System Performance. P0870 - OD Hydraulic Pressure Test. P040B - Exhaust Gas Recirculation Temperature Sensor "A" Circuit Performance. P2201 - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 1. P1C54 - SCR NOx Catalyst Missing. P249E - Closed Loop SCR Reductant Injection Control At Limit - Flow Too High. P0128 - Thermostat Rationality. P24C7 - Particulate Matter Sensor Temperature Circuit Performance. Customers may also comment on the following:Engine misfire in cold ambient temperatures. In addition, the following software enhancements are also available:Scan tool fan actuation test fix. Enabling diagnostics forDTC P208B- Reductant Pump 1 Control Performance. Unable to turn on the ability to set ?MAX? road speed using wiTECH scan tool. Mass Air Flow (MAF) sensor Out Of Range (OOR) low calibration. Improved 5-4 shift (reduce shift flare) after extended operation in 5th or 6th gear. Engine Manifold Pressure Misfire Monitor (EMP MFM) retune(Sales Code DG7 Only). Idle based misfire retune. Abort timer for Selective Catalytic Reduction (SCR) out NOx sensor missing change to 70 seconds. Map SCR missingFault/DTC P1C54to tampering inducement. Particulate Matter (PM) sensor false fault improvement. CC inner loop used up faults. Ultrasonic Flow Meter (UFM) test results fix. Engine run state idle unstable software fix. Ability to write Engine Serial Number (ESN
S1918000003RevA2022-10-17. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. Revision A: Intermittent Engine Buck, Surge, or Misfire.
18131222022-10-17. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the PCM with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set: P064F - Unauthorized Software/Calibration Detected. P229F - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2. P207F - Reductant Quality Performance. P249E - Closed Loop Scr Reductant Injection Control At Limit - Flow Too High. P2509 - PCM/PCM Power Input Signal Intermittent. P0128 - Thermostat Rationality. P2201 - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 1. In addition, the following software enhancements are also available:Scan Tool Fan Actuation Test fix. Enabling DTC P208B - Reductant Pump 1 Control Performance. Mass Air Flow (MAF) Sensor Out Of Range (OOR) low calibration. Idle based misfire retune. Abort timer for Selective Catalytic Reduction (SCR) Out NOx Sensor missing change to 70 seconds. Map SCR missing DTC/Fault (P1C54) to tampering inducement. Particulate Matter (PM) Sensor False Fault Improvement. CC inner loop used up faults. Ultrasonic Flow Meter (UFM) test results fix. Engine run state idle unstable software fix. Ability to write Engine Serial Number (ESN) through wiTECH. Add Diesel Exhaust Fluid (DEF)/Reagent type as a readable value in wiTECH. Fan actuation test. SCR missing tuning capability improvement. Smart tampering improvement.
S22080000732022-10-17. Service bulletin. POWER TRAIN. No Start, After Flash And Or PCM Replace, DTC P0513 Invalid Skim Key Setting
90044452022-10-17. Service bulletin. POWER TRAIN. Transfer Case Shift Lever Design Change
18061202022-09-26. Service bulletin. POWER TRAIN. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:P0868 - Line Pressure Low (Module, Powertrain Control (PCM), 68RFE). P229F - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2. P207F - Reductant Quality Performance. P2509 - PCM/PCM Power Input Signal Intermittent. P0401 - EGR System Performance. P0870 - OD Hydraulic Pressure Test. P040B - Exhaust Gas Recirculation Temperature Sensor "A" Circuit Performance. P2201 - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 1. P1C54 - SCR NOx Catalyst Missing. P249E - Closed Loop SCR Reductant Injection Control At Limit - Flow Too High. P0128 - Thermostat Rationality. P24C7 - Particulate Matter Sensor Temperature Circuit Performance. Customers may also comment on the following:Engine misfire in cold ambient temperatures. In addition, the following software enhancements are also available:Scan tool fan actuation test fix. Enabling diagnostics forDTC P208B- Reductant Pump 1 Control Performance. Unable to turn on the ability to set ?MAX? road speed using wiTECH scan tool. Mass Air Flow (MAF) sensor Out Of Range (OOR) low calibration. Improved 5-4 shift (reduce shift flare) after extended operation in 5th or 6th gear. Engine Manifold Pressure Misfire Monitor (EMP MFM) retune(68RFE Only). Idle based misfire retune. Abort timer for Selective Catalytic Reduction (SCR) out NOx sensor missing change to 70 seconds. Map SCR missingFault/DTC - P1C54to tampering inducement. Particulate Matter (PM) sensor false fault improvement. CC inner loop used up faults. Ultrasonic Flow Meter (UFM) test results fix. Engine run state idle unstable software fix. Ability to write Engine Serial Number (ESN) through wiTE
S18210000012022-09-26. Service bulletin. POWER TRAIN. Gear Ratio DTC?s, Transmission Shift Concerns, Does Not Shift At Times, Shudders
90040092022-09-26. Service bulletin. POWER TRAIN. Transmission Kit with Torque Converter 1. All Promaster (VF) 3.6L/62TE equipped vehicles. If the transmission bracket to the transmission case fasteners are removed during servicing, the fasteners (Part Number 06511385A$) are one-time usage. Vehicles built prior to 10/23/2015 requires Service Kit PN 68461214AA; includes Transmission Isolator PN 68264483AA, and Adaptation Bracket 68264479AA and Fastener Service Kit PN 68329056AA Vehicles built after on or after 10/23/2015 will require only the Fastener Service Kit PN 68329056AA. 2. All 3.6L/62TE equipped vehicles. If the vehicle you are repairing has a crack in the flex plate or failed pump bushing inspect and confirm that both (2) dowel pins are present in the engine block, which align the transmission center line to the crank shaft centerline and visually inspect the dowel alignment holes in the transmission case. If the holes are damaged or elongated the transmission should be replaced to prevent further damage to the transmission/flexplate or pump bushing due to the inability to properly align the engine to the transmission during the repair. 3. All 62TE equipped vehicles. If pump bushing is scored or damaged and the dowel pin alignment holes are ok, replace the pump assembly as opposed to complete transmission. 4. All 62TE equipped vehicles. If vehicle is jerking/slipping with MIL code(s) P0740 or P2764, check TCC Solenoid operation. If TCC Solenoid is ok, the codes are indicative of a torque converter failure. Replace the torque converter.
21043192022-09-15. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Flash: Transmission Control Module (TCM) Updates This bulletin involves reprogramming the TCM with the latest available software. The customer may notice a harsh 2-3 and 3-4 shift. The following software enhancements are available:2-3 and/or 3-4 shift improvements.
21-049-172022-08-08. Service bulletin. POWER TRAIN; POWER TRAIN:AUTOMATIC TRANSMISSION:FLUID/LUBRICANT; EXTERIOR LIGHTING. Incorrect Transmission Oil Level Indicator This bulletin involves inspecting and replacing the transmission oil level indicator (dipstick) if needed. During a new vehicle preparation, the technician may notice the transmission fluid level is low.
90038142022-08-08. Service bulletin. POWER TRAIN. Power Distribution Center For 2018 D2/DD/DF/DJ/DP, prior to replacing the Power Distribution Center (PDC), you MUST contact the STAR Center (800) 850-7827 for diagnostic assistance and pre- authorization. Failure to do so WILL result in your warranty claim being rejected.
21-049-172022-07-25. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; POWER TRAIN. Incorrect Transmission Oil Level Indicator This bulletin involves inspecting and replacing the transmission oil level indicator (dipstick) if needed. During a new vehicle preparation, the technician may notice the transmission fluid level is low.
S2008000113 Rev.2021-05-24. Service bulletin. POWER TRAIN. No Start Intermittently, Vehicle Requires Multiple Keyless Push To Start Attempts To Start Vehicle, Intermittent Key Not Detected Message
S1625000007 Rev.2021-03-15. Service bulletin. EXTERIOR LIGHTING; EQUIPMENT; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM). Malfunction Indicator Lamp (MIL) Illumination. Diagnostic Trouble Code (DTC) P207F ? Reductant Quality Performance Set.
18-061-20 REV. A2020-11-30. Service bulletin. ENGINE; ELECTRICAL SYSTEM:SOFTWARE; POWER TRAIN. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:P2706 - MS Solenoid Circuit(Sales Code DG7 Only). P0868 - Line Pressure Low. P229F - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2. P207F - Reductant Quality Performance. P2509 - PCM/PCM Power Input Signal Intermittent. P0401 - EGR System Performance. P0870 - OD Hydraulic Pressure Test. P040B - Exhaust Gas Recirculation Temperature Sensor "A" Circuit Performance. P2201 - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 1. P1C54 - SCR NOx Catalyst Missing. P249E - Closed Loop SCR Reductant Injection Control At Limit - Flow Too High. P0128 - Thermostat Rationality. P24C7 - Particulate Matter Sensor Temperature Circuit Performance. Customers may also comment on the following:Engine misfire in cold ambient temperatures. In addition, the following software enhancements are also available:Scan tool fan actuation test fix. Enabling diagnostics forDTC P208B- Reductant Pump 1 Control Performance. Unable to turn on the ability to set ?MAX? road speed using wiTECH scan tool. Mass Air Flow (MAF) sensor Out Of Range (OOR) low calibration. Improved 5-4 shift (reduce shift flare) after extended operation in 5th or 6th gear. Engine Manifold Pressure Misfire Monitor (EMP MFM) retune(Sales Code DG7 Only). Idle based misfire retune. Abort timer for Selective Catalytic Reduction (SCR) out NOx sensor missing change to 70 seconds. Map SCR missingFault/DTC P1C54to tampering inducement. Particulate Matter (PM) sensor false fault improvement. CC inner loop used up faults. Ultrasonic Flow Meter (UFM) test results fix. Engine run state idle unstable software fix. Ability to write Engine Serial Number (ESN
08-094-202020-11-30. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN:TRANSFER CASE (4-WHEEL DRIVE); EQUIPMENT. Flash: Drivetrain Control Module (DTCM) Update This bulletin involves reprogramming the DTCM with the latest available software. The customer may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Code (DTC) has been set::If the customer has any concerns with the transfer case or if the tech performs any repairs on the transfer case, the software must be updated.C140E - Transfer Case Motor Blocked. If DTC C140E is present, follow normal diagnostic procedures before updating the DTCM.In addition the customer may describe the following:The ?Service 4WD? message/fault is displayed in the Instrument Panel Cluster (IPC). Transfer case shift fork tabs broken during range shift. Noisy (clunking/ratcheting) transfer case range shifts. Failure to complete transfer case range shifts. The following software enhancement is available:This update will help reduce premature transfer case failure.
18-061-202020-09-28. Service bulletin. ELECTRICAL SYSTEM; ENGINE; EQUIPMENT; POWER TRAIN. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find that one or more of the following DTCs have been set:P0868 - Line Pressure Low (Module, Powertrain Control (PCM), 68RFE). P229F - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 2. P207F - Reductant Quality Performance. P2509 - PCM/PCM Power Input Signal Intermittent. P0401 - EGR System Performance. P0870 - OD Hydraulic Pressure Test. P040B - Exhaust Gas Recirculation Temperature Sensor "A" Circuit Performance. P2201 - Aftertreatment NOx Sensor Circuit Performance - Bank 1 Sensor 1. P1C54 - SCR NOx Catalyst Missing. P249E - Closed Loop SCR Reductant Injection Control At Limit - Flow Too High. P0128 - Thermostat Rationality. P24C7 - Particulate Matter Sensor Temperature Circuit Performance. Customers may also comment on the following:Engine misfire in cold ambient temperatures. In addition, the following software enhancements are also available:Scan tool fan actuation test fix. Enabling diagnostics forDTC P208B- Reductant Pump 1 Control Performance. Unable to turn on the ability to set ?MAX? road speed using wiTECH scan tool. Mass Air Flow (MAF) sensor Out Of Range (OOR) low calibration. Improved 5-4 shift (reduce shift flare) after extended operation in 5th or 6th gear. Engine Manifold Pressure Misfire Monitor (EMP MFM) retune(68RFE Only). Idle based misfire retune. Abort timer for Selective Catalytic Reduction (SCR) out NOx sensor missing change to 70 seconds. Map SCR missingFault/DTC - P1C54to tampering inducement. Particulate Matter (PM) sensor false fault improvement. CC inner loop used up faults. Ultrasonic Flow Meter (UFM) test results fix. Engine run state idle unstable software fix. Ability to write Engine Serial Number (ESN) through wiTE

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.