Service bulletins for the 2015 Ram 3500
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
523 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| 1807622 | 2022-12-19. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); FUEL SYSTEM, GASOLINE; POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE:SOFTWARE; ELECTRICAL SYSTEM; ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM); EXTERIOR LIGHTING; ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE; FUEL SYSTEM, DIESEL; SERVICE BRAKES, HYDRAULIC; BACK OVER PREVENTION. Flash: Powertrain Control Module (PCM) Updates This bulletin involves reprogramming the Engine Control Module/Powertrain ControlModule (ECM/PCM) with the latest available software. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of thefollowing DTCs have been set: P064F - Unauthorized Software/Calibration Detected. P202E - (Diesel Exhaust Fluid) Reductant Injector Performance. P24A5 - EGR Cooler Bypass Bank 1 Control Stuck. P1C55 - NOx Sensor Intermittent ? Bank 1 Sensor 1. P0301 - Cylinder 1 Misfire. P0302 - Cylinder 2 Misfire. P0303 - Cylinder 3 Misfire. P0304 - Cylinder 4 Misfire. P0305 - Cylinder 5 Misfire. P0306 - Cylinder 6 Misfire. P020A - Fuel Injector 1 Performance. P020B - Fuel Injector 2 Performance. P020C - Fuel Injector 3 Performance. P020D - Fuel Injector 4 Performance. P020E - Fuel Injector 5 Performance. P020F - Fuel Injector 6 Performance. U0001 - Can C Bus. P1451 - Diesel Particulate Filter System Performance. P229E - NOx Sensor Circuit - Bank 1 Sensor 2. P218F - Reductant No Flow Detected. P242F - Diesel Particulate Filter Restriction - Ash Accumulation. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor CircuitIntermittent (setting when the block heater is plugged in). U110E - Lost Ambient Temperature Message. P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. P2281 - Air Leak Between MAF And Throttle Body. P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. U1421 - Implausible Ignition Key Off Time Received. P026B - Injection Timing Performance. In addition, the following software enhancements are also available: A/C pressure sensor update. Improvements made to reduce misfire. wiTECH engine cooling fan actuation test update. Improved Exhaust Gas Recirculation (EGR) valve response. Over Running Clutch (ORC) software improvement. Unpleasantodor in the vehicle at low speeds during regeneration cycle. |
|---|---|
| V51 | 2022-12-19. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION:CONTROL MODULE (TCM/PCM/TECM); UNKNOWN OR OTHER. Customer Satisfaction Notification V51 Reprogram Powertrain Control Module |
| S2209000004 | 2022-12-19. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. If a Mopar oil filter is not available, use a filter that meets or exceeds USCAR36 specification and is compatible with semi and full synthetic oils. |
| Parts | 2022-11-21. Service bulletin. STRUCTURE; EQUIPMENT. Center Console. |
| 2500116 | 2022-11-21. Service bulletin. ENGINE AND ENGINE COOLING; FUEL SYSTEM, DIESEL. Diagnosing A Urea Module That Is Exposed To Diesel Fuel This bulletin involves discussing what will happen to the rubber material used in the urea pump when exposed to diesel fuel. This unit is sometimes referred to as the Selective Catalyst Reductant (SCR) module or the Adblue Delivery Module (ADM). Units exposed to hydrocarbons have a particular failure mode, the rubber heater unit is crinkled and in some cases the metal heater protrudes through the rubber membrane. The rubber material used in this unit is designed to withstand Diesel Exhaust Fluid (DEF) only. Exposure to fluids that contain hydrocarbons (i.e. diesel fuel) will damage the unit beyond repair. Units returned that exhibit this failure mode will have warranty claims that are rejected. Units that exhibit this failure mode should be considered customer abuse and should not be covered under warranty. Use the Hydroscopic test paper (P/N 223-44-863) available through MoparEssentialTools.com to confirm exposure. |
| 1806216 | 2022-11-21. Service bulletin. ELECTRICAL SYSTEM; POWER TRAIN. Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: · **P0335 - Crankshaft Position Sensor Circuit. · P0456 - EVAP System Small Leak. · P2610 - PCM Internal Engine Off Timer Performance.** · P0300 - Multiple Cylinder Misfire. · P0301 - Cylinder 1 Misfire. · P0302 - Cylinder 2 Misfire. · P0303 - Cylinder 3 Misfire. · P0304 - Cylinder 4 Misfire. · P0305 - Cylinder 5 Misfire. · P0306 - Cylinder 6 Misfire. · P0307 - Cylinder 7 Misfire. · P0308 - Cylinder 8 Misfire. |
| S2214000003 | 2022-11-07. Service bulletin. FUEL SYSTEM, DIESEL. Guidelines For The Use Of Alternative Diesel Fuels. |
| 9004470 | 2022-11-07. Service bulletin. STRUCTURE:BODY:BUMPERS; ELECTRICAL SYSTEM:WIRING:CONNECTORS/PLUGS/RECEPTACLES; TRAILER HITCHES. CONNECTOR Trailer Tow,WIRING Trailer Tow,CONNECTOR 7 Way,WIRING Rear Bumper If the connector or wiring is physically damaged, burned, melted or corroded, prior to replacing the part, please contact FCA Redacted Content If no response in 15 minutes, proceed with repair. Please send pictures of the failed part to FCA Redacted Content |
| 3100122 | 2022-10-31. Service bulletin. STRUCTURE. Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components. |
| 3100122 | 2022-10-31. Service bulletin. STRUCTURE:INTERIOR PANELS:DOOR; STRUCTURE; UNKNOWN OR OTHER. Approved Use of Weld Through Primers This bulletin documents the FCA US LLC position regarding the use of weld through primer when using Squeeze Type Resistance Spot Welding (STRSW) and Gas Metal Arc Welding (GMAW) processes when welding steel body panels and structural components. |
| 9003319 | 2022-10-24. Service bulletin. ELECTRICAL SYSTEM; BACK OVER PREVENTION; POWER TRAIN; ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER. Turbocharger, Turbo Speed Sensor, Turbo Gaskets and Seals 1. Do Not Replace Turbocharger for Exhaust Brake Operation Complaints. Do not replace the turbocharger for complaints of exhaust brake operating when the Exhaust Brake switch is off. Replacing the turbocharger will not address these complaints. Update the PCM with the new software version to correct this issue. 2. Turbo Speed Sensor is Now Serviceable. If a Turbocharger Speed Sensor is being replaced for a P2580 or any other reason, the Turbo Speed Sensor is now available separate from the Turbocharger Kit. do not replace the entire Turbocharger Kit. 2013-2015 Chassis Cab or Pickup - PN 68210095A$ 2007-2012 Chassis Cab or Pickup - PN 68039104A$. 3. Replace Exhaust Gaskets with Turbocharger Removal.~ If turbocharger is removed/replaced, the following items are not reusable and must be replaced: Turbocharger Gasket Turbocharger Outlet Seal Turbocharger Band Clamp If the front exhaust pipe is removed/replaced, the following items are not reusable and must be replaced. Turbocharger Outlet Seal Turbocharger Band Clamp |
| 2300116REVD | 2022-10-24. Service bulletin. EQUIPMENT. Center Console Lid Binding |
| 0804616 | 2022-10-24. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Bulletin involves updating the (ASCM) software. |
| 0900416REVA | 2022-10-24. Service bulletin. ELECTRICAL SYSTEM. Cummins Service Engine Replacement This bulletin involves replacing the engine assembly. Remanufactured long block or short block was installed during a prior repair. A new replacement engine will be installed. |
| 18-038-16 | 2022-10-24. Service bulletin. ELECTRICAL SYSTEM; FUEL SYSTEM, DIESEL; FUEL SYSTEM, GASOLINE; EXTERIOR LIGHTING. P20EE SCR NOX Catalyst Efficiency Below Threshold Bank 1 This bulletin involves verifying the proper operation of the Diesel Exhaust Fluid (DEF) system and, if necessary, replacing the Selective Catalyst Reduction (SCR) Catalyst assembly. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find Diagnostic Trouble Code (DTC) P20EE SCR NOX Catalyst Efficiency Below Threshold Bank 1 set in the Powertrain Control Module (PCM) memory. |
| 18-037-16 | 2022-10-24. Service bulletin. FUEL SYSTEM, DIESEL; SERVICE BRAKES, HYDRAULIC; FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM; POWER TRAIN; EXTERIOR LIGHTING; BACK OVER PREVENTION; ELECTRONIC STABILITY CONTROL:AUTOMATIC (ASC). Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: · **P218F - Reductant No Flow Detected. · P242F - Diesel Particulate Filter Restriction - Ash Accumulation.** · P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). · U110E - Lost Ambient Temperature Message. · P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. · P2281 - Air Leak Between MAF And Throttle Body. · P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. · U1421 - Implausible Ignition Key Off Time Received. · P026B - Injection Timing Performance. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: · **Ambient Air Temperature Improvements. · 68RFE Transmission Overall Shift Quality Improvements.** · SCR Efficiency scan tool test improvement. · Charging system improvements for single alternator applications (Changes the cutout threshold from 600 to 500 RPM). · Diesel Exhaust Fluid (DEF) system calibration improvement during Stationary Regeneration. · Cold idle speed stability improvement. · Charging system improvements for dual alternator applications. · Torque increase to 865 ft/lbs (D2 vehicles equipped with the Aisin transmission sales code DF2 only). · Fuel Filter Minder calibration changes. · wiTECH Fuel Pressure Override and Fuel System Run Up test improvements. |
| 18-036-16 | 2022-10-24. Service bulletin. ELECTRICAL SYSTEM. SUBJECT: Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module (ECM) with the latest available software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo diesel. |
| S1908000102 | 2022-10-17. Service bulletin. POWER TRAIN. (Rev. A) Power Inverter Load Ratings |
| 68158770 | 2022-10-17. Service bulletin. ELECTRICAL SYSTEM:WIRING:CONNECTORS/PLUGS:ACCESORY POWER OUTLET/JACK/PORT/USB/SAE/CIGARETTE LIGHTER. USB Charging Port Before replacing this part - this is a charge only USB port intended to charge smart phones and other low power USB devices. To verify proper functionality, turn on the ignition with no cables or devices plugged into the port. Connect a charging cable to the port, then connect the device. If the device receives power, the port is functioning to design. There are some minor compatibility issues with some charging cables including Apple Lightning cables. For questions regarding the charging port functionality, please call Dave Diovardi at Cell (248) 941-8704 or Rick Gordon at Cell (248) 630-6281.~ |
| 68234041 | 2022-10-17. Service bulletin. ENGINE AND ENGINE COOLING; VISIBILITY:DEFROSTER/DEFOGGER/HVAC SYSTEM. Thermal Expansion Valve (TXV), H-valve For D trucks only; When diagnosing an A/C system leak at the TXV (Thermal Expansion Valve, H-valve), do not replace the TXV unless it has been proven to be defective for function or for a leak. Instead replace just the O-ring(s) part number 05161806AA, 68046015AA, 68100682AA, 68100676AA. For any questions call Matt Mihm cell (248) 736-6542. If no response in 15 minutes, please continue with repair.~ ~___________________________________________________________________~ Contact us at CAGRIS@Chrysler.com for feedback related ONLY to this GPOP Tech Tip. Please include the Part Number(s) and Tech Tip Part Description of the Tech Tip you are referencing for our tracking system. |
| 05086755 | 2022-10-17. Service bulletin. ENGINE AND ENGINE COOLING. Rear Crank Shaft Oil Seal and Retainer Plate For Cummins equipped vehicles only;~ If you are working on a 2015 or 2016 vehicle ONLY and are replacing the Rear Main Seal for oil leak, replace seal, retainer and gasket using PNs; 05086755A, 05086754A, 05015705A. Remove the retainer with the seal installed. Please do not disturb seal in retainer when removing from engine. Please refer to detailed repair instructions in DealerConnect TechConnect for oil seal retainer replacement.~ Cummins Engineering is currently investigating the root cause of the oil leak concern and would like to analyze these parts. Please contact Chad Eichbrecht at cell (248) 309-2695 to arrange for part return~ If you do not receive a response within 15 minutes, please proceed with normal repair. ~_________________________________________________________________~ Contact us at CAGRIS@Chrysler.com for feedback related ONLY to this GPOP Tech Tip. Please include the Part Number(s) and Tech Tip Part Description of the Tech Tip you are referencing for our tracking system. |
| 05152029 | 2022-10-17. Service bulletin. VISIBILITY/WIPER. Washer Fluid Level Sensor Prior to replacing this part due to "Low Washer Fluid" tell tale light on the dash and the washer fluid bottle is full, please perform the this inspection. Inspect the sensor for a fluid coating on the sensor pins. Orange colored rain repellant can cause this fluid build-up. Clean the pins, drain the reservoir, and fill with Mopar approved washer fluid. Check to determine if the issue has been resolved. Continue with repair if necessary. Also, please inform the customer not to use Rain-X in the system to avoid this issue. Please contact Chuck Hood at cell (248) 613-7591 if you have questions or need additional information. Thank you. |
| 68332810 | 2022-10-17. Service bulletin. ENGINE AND ENGINE COOLING. Service - Four Piece Oil Pan Gasket All Cummins Equipped Vehicles ONLY - The replacement oil pan gasket can be a four piece gasket rather than a single piece gasket. This applies to Cummins 5.9L and 6.7L engines only. Installation: 1. Clean the oil pan T-joints.~ 2. Fill the T-joint between the pan rail/gear housing and pan rail/rear seal retainer with sealant. Use Mopar® Silicone Rubber Adhesive Sealant or equivalent. 3. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the oil pan flange.~ 4. The four piece gasket will need to be assembled to make a complete oil pan gasket. 5. Lay the oil pan gasket(s) onto the oil pan flange.~ 6. Ensure the oil pan gasket segment joints are properly aligned. 7. Apply a 2-mm [0.063-in] bead of Mopar Engine Sealant RTV Silicone Rubber Adhesive, to the top of the oil pan gasket.~ 8. Install the oil pan. Starting from the center and working outward, tighten the oil pan bolts to 28 N·m [21 ft. lbs.]. |
| 0900522REVA | 2022-10-17. Service bulletin. ENGINE AND ENGINE COOLING:ENGINE:GASOLINE:TURBO/SUPERCHARGER; ELECTRICAL SYSTEM. Cummins 6.7L Turbocharger Actuator - X99 Warranty Extension This bulletin involves replacing the turbocharger actuator. Customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technicianmay find that one or more of the following DTCs have been set: U010C - Lost Communication With Turbocharger/Supercharger Control Module. P003A - Turbocharger Boost Control Module Position Exceeded Learning Limit. P00AF - Turbocharger Boost Control Module Performance. P0046 - Turbocharger Boost Control Circuit Performance. |
| 0802817 | 2022-10-17. Service bulletin. EQUIPMENT:ELECTRICAL. This bulletin provides information regarding the latest Flash Over The Air update (FOTA) and provides a service technician an overview of the steps a customer will need to take to complete the update. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.