WenmarOpen by Wenmar Pro

Service bulletins for the 2015 Ram 3500

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

523 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
23-001-16 REV. D2018-06-11. Service bulletin. EQUIPMENT. Center Console Lid Binding This bulletin involves adding a rubber bumper to the console lid to prevent the lid from binding. The customer may describe a binding or audible clicking condition when the center console lid is being opened or closed.
08-046-162018-06-11. Service bulletin. SUSPENSION. Flash: Air Suspension Control Module (ASCM) System Enhancements This Bulletin involves updating the (ASCM) software. A customer may describe the following: · **Cluster stays awake after ignition is turned off for 10 minutes or more.** · False message Battery Voltage Low - Start Engine to Change Ride Height which appears in the Electronic Vehicle Information Center (EVIC). This condition may happen when the vehicle is first started and trying to move the suspension from trailer ride height to normal ride height.
68277402A2018-06-11. Service bulletin. VEHICLE SPEED CONTROL:CRUISE CONTROL. Adaptive Cruise Control Sensor 1) If you are replacing this part due to the cluster displaying Clean Radar Sensor in Front of Vehicle or DTC C1266 ACC Sensor Blinded, please verify that there is no blockage in front of the sensor. Blockage can occur from mud, ice, snow, front end damage, bracket damage, the sensor not attached to the bracket properly or an aftermarket fascia installed. This fault can occur intermittently in muddy or icy/snowy conditions and is considered normal operation. Under some circumstances, a misaligned sensor can also cause the C1266 DTC, please complete an alignment procedure. No replacement is required.~ 2) If you are replacing this part due to the cluster displaying ?ACC/FCW Unavailable Service Required?, please check the DTC fault codes. This will indicate which module needs to be serviced (TCM, PCM, ESP/ABS, etc). This fault is not due to the ACC Sensor. No sensor replacement is required.~ 3) If you have fault code DTC C125E ACC Sensor Adjustment Required, please verify that the radar sensor is fully seated in the clips and there is no damage (if clips are damaged on a 2013 or earlier vehicle, order P/N 68085813A$, otherwise please replace the module), please verify there is no blockage to the sensor due to mud, ice, snow, front end damage, bracket damage or the sensor not attached to the bracket properly. Perform the Vertical Alignment and the Electronic Horizontal Alignments procedure as stated in the service manual. Please note, if the horizontal alignment procedure will not complete, check the vertical alignment and confirm that the sensor is seated properly. Rerun the horizontal alignment procedure. No sensor replacement is required. **Hints for running Horizontal Alignment procedure: A) Verify speed is between 45 and 75 mph, B) verify the road is relatively straight with signs, poles, guard rails, etc C) Do not tail a vehicle too closely this inhibits the learning procedure
RL305553A2018-06-11. Service bulletin. POWER TRAIN. 9-spd Transmission: FOR NAFTA Market Only: If you are ordering this transmission please follow all wiTECH pop ups and Warranty Payment Guidelines. If this vehicle contains 1 of the 30 Diagnostic Codes in the 9 Speed Tutorial located on the Service Home Page then please follow the repair steps and submit a Topology report as well as a Vehicle Scan Report with the Warranty Claim.~
68105583A2018-06-11. Service bulletin. ENGINE AND ENGINE COOLING. Pentastar Oil Filter Adapter: Before replacing this part, please call any one of the following people. Engineering is seeking information regarding this part.~ Dye must be used to determine where the leak is coming from before replacing. Also please check the recently updated Service Bulletin Number 09-008-15. ~ First: Nick Morand Cell (248) 410-8078 - Nick.morand@fcagroup.com Second: Bob Jackson Cell (248) 944-0466 - bob.jackson@fcagroup.com Third: Joe Lovell Cell (734 309-6467 - joe.lovell@fcagroup.com If a response is not received within 15 mins, then proceed with the necessary repair.~
5RR541XRA2018-06-11. Service bulletin. VISIBILITY:REARVIEW MIRRORS/DEVICES. Power Fold Rearview Mirror Prior to replacing this part for a loose mirror, please first follow this procedure to reset the pivot mechanism. Move the mirror to its full forward position and then to full retract position using the power fold mirror button located on drivers side door panel. Perform this procedure three times. If this doesn't resolve the issue, then repair as necessary.~ Note: 1- The looseness of power fold mirror does not necessary indicate a defective mirror, it may be caused by folding it manually rather than using the power fold feature. If the mirror is adjusted manually out of the proper detent, always use the button to adjust it back into sync.~ 2- The intended use of the power fold mirrors is by pushing the button to fold and unfold the mirror. Only manually fold the mirrors when absolutely necessary.~ 3- In the circumstance where the left hand mirror and right hand mirror are in different positions, it may take up to three cycles (bottom pushes) to re-sync the mirrors together.
08-079-14 REV. C2018-06-11. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; ELECTRICAL SYSTEM:SOFTWARE. RA3 RA4 Radio Enhancements This bulletin involves inspecting and, if required, updating the radio software. A small number of customers may experience one or more of the following: Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only) The Radio may switch from SiriusXM to an AM station by itself Uconnect registration always present, can not remove Uconnect account Teleprompter does not appear when pressing the Voice Recognition (VR) button VR operation cancels while in media mode Radio may display previous cameras image before displaying the current image Navigation lost vehicle position, during route calculation Navigation displays are missing after vehicle heading changes Navigation giving incorrect guidance to exit the highway FM audio may switch to AM after ignition cycle Text messages appear as sender?s phone number not their name. VR phone button may not work at times Audio muted after AUX device is disconnected VR, ? Listen? to text, will only play 1st message Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only) SirusXM station information does not update. Speed adjusted volume, may not work AM or FM seek or tuner soft keys may be missing Display screen show ambient temperature as ?- - ? not normal values.Improvements: High Definition (HD) radio buffering. Spanish translation. Radio station, scroll feature. Drive Mode: Launch control button, text improvements (LA, LD, LX and ZD Only). Making assist calls. App functionality and screen displays. Displays correct media, song titles and tracks. Travel Link, Points Of Interest (POI), displaying movies and favorites. Incoming calls, audio enhancements (LA, LD and LX Only). Audio for strong AM stations. VR performance. Settings can only be changed in run mode, not ACC.
08-108-142018-06-11. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; ELECTRICAL SYSTEM:SOFTWARE. RA2 Radio Software Enhancements This bulletin involves updating the radio's software. A customer may have experience one or more of the following: Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. Touchscreen confirmation beep may be too loud (Grand Cherokee only). U0208-00 - Loss Communication With Heated Seat Control Module (Cherokee only).Improvements: Only allow vehicle settings to be changed in run mode. To help insure settings are properly saved. Always gray out text message soft keys for non-supporting devices. Voice Recognition (VR) improved accuracy.
08-109-142018-06-11. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; ELECTRICAL SYSTEM:SOFTWARE. RG2 Or RJ2 Radio Software Enhancements This bulletin involves updating the radio's software. A customer may have experience one or more of the following: Not able to change state of heated seats and/or steering wheel during stop event on Stop/Start vehicles. Touchscreen confirmation beep may be too loud. The radio does not allow selection of the Polish language. The radio fan continually runs at high speed. Customer perception may be the radio fan is too loud.Improvements: Only allow vehicle settings to be changed in run mode. To help insure settings are properly saved. Always gray out text message soft keys for non-supporting devices. Voice Recognition (VR) improved accuracy.
21-037-142018-06-11. Service bulletin. POWER TRAIN. 66RFE Transmission Slip Under High Engine Load And Premature Wear This bulletin involves inspecting the torque converter build date and if necessary, replacing the torque converter. A small number of torque converters were manufactured with the oil grooves on the internal friction discs too wide. This may result in the transmission slipping under heavy loads causing premature wear.
08-096-142018-06-11. Service bulletin. VISIBILITY. Uconnect Access Buttons On The Rear View Mirror Are Inoperative This bulletin involves reconfiguring the vehicle for proper Uconnect Access operation. The customer may notice that the Uconnect Access feature is inoperative. Pressing either button (Assist or 9-1-1) on the rear view mirror will not activate that feature.
18-052-142018-06-11. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Flash: 6.7L Diagnostic And System Improvements This bulletin involves selectively erasing and reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with new software. Several software improvements are available for vehicles equipped with a Cummins 6.7L turbo diesel.Improvements To Prevent Or Reduce Unnecessary Malfunction Indicator Lamp (Mil) Illumination For: P2281 - Air Leak Between MAF And Throttle Body. U1421 - Implausible Ignition Key Off Time Received. P026B - Injection Timing Performance.Other Software Improvements: Charging system improvements for dual alternator applications. Torque increase to 865 ft/lbs (D2 vehicles equipped with the Aisin transmission sales code DF2 only) Fuel Filter Minder calibration changes. wiTECH Fuel Pressure Override and Fuel System Run Up test improvements
STAR News No. 852018-06-11. Service bulletin. EQUIPMENT. STAR receives on average 1,000 contacts per day ? that?s 300,000 annual contacts for technical assistance. This same month last year we had over 40,000 open aged > 5 days tickets. As a result of focused efforts to verify vehicles are repaired and close tickets the number is now at just under 7,000 tickets.
25-003-142018-06-11. Service bulletin. EQUIPMENT. Information: P207F P1C70 And SCR Inducement Strategy
BJA465972018-06-11. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; POWER TRAIN. Job aid - If you have a suspected TC shudder/vibration, check the Interactive Network for Service Bulletins for the vehicle you are working on. A test-drive snap shot may help you isolate the source of the issue.
18-037-16 REV. A2018-06-04. Service bulletin. POWER TRAIN; FUEL SYSTEM, GASOLINE; ELECTRICAL SYSTEM; EXTERIOR LIGHTING; FUEL SYSTEM, DIESEL; ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE. Flash: 6.7L Diagnostic And System Improvements This bulletin involves reprogramming the Engine Control Module/Powertrain Control Module (ECM/PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation a technician may find one or more of the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: · P218F - Reductant No Flow Detected. · P242F - Diesel Particulate Filter Restriction - Ash Accumulation. P205E - (Diesel Exhaust Fluid) Reductant Tank Temperature Sensor Circuit Intermittent (setting when the block heater is plugged in). · U110E - Lost Ambient Temperature Message. · P20E8 - (Diesel Exhaust Fluid) Reductant Pressure Too Low. · P2281 - Air Leak Between MAF And Throttle Body. P1477 - Intake Air Diverter Valve Position Sensor Circuit Shorted To Ground. U1421 - Implausible Ignition Key Off Time Received. · P026B - Injection Timing Performance. In addition to addressing the above DTCs, the following powertrain system improvements/enhancements are also included in this software release: · NOx sensor calibration improvements. (Sales Code DG7). Enhanced software for a No crank/No start issue. (U0100 - Lost Communication With ECM/PCM). (Sales Code DG7).** · Ambient Air Temperature (AAT) improvements. · 68RFE Transmission overall shift quality improvements. · SCR Efficiency scan tool test improvement. · Charging system improvements for single alternator applications (Changes the cutout threshold from 600 to 500 RPM). · Diesel Exhaust Fluid (DEF) system calibration improvement during Stationary Regeneration. · Cold idle speed stability improvement. Charging system improvements for dual alternator applications. · Torque increase to 865 ft/lbs (D2 vehicles equipped with the Aisin transmission sales code DF2 only). Fuel Filter Minder calibration changes. · wiTECH Fuel Pressure Override and Fuel System Run Up test improvements.
08-053-162018-06-04. Service bulletin. EQUIPMENT; PARKING BRAKE; ELECTRICAL SYSTEM. Flash: RA3/RA4 Radio Software Enhancements This bulletin involves inspecting and, if required, updating the radio software. A small number of customers may experience one or more of the following: · Poor or no connection to cellular network (U.S. market only). · HVAC temperature out of sync with radio display (KL vehicles).** · Intermittently blind spot chime will not turn off (KL vehicles only). · Enable High Definition (HD) feature (RA4 radios located in Canada and Mexico). Low battery condition due to the radio remaining powered up after the ignition has been turned off (U.S Markets Only). The Radio may switch from SiriusXM to an AM station by itself. · Uconnect registration always present, can not remove Uconnect account. · Teleprompter does not appear when pressing the Voice Recognition (VR) button. VR operation cancels while in media mode. · Radio may display previous image before displaying the current image. · Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. · FM audio may switch to AM after ignition cycle. · Text messages appear as sender's phone number not their name. VR phone button may not work at times. · Audio muted after AUX device is disconnected. · VR, Listen, to text will only play first message. · Drive Mode: Eco, sport or normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). · Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). · SirusXM station information does not update. · Speed adjusted volume, may not work. AM or FM seek or tuner soft keys may be missing. · Display screen show ambient temperature as ?- - ? not normal values. Improvements: · **User can pair iPhone with Uconnect via Bluetooth and talk to Siri through Uconnect. · Ability to press VR button for more than one second.** · Faster response time when using the Remote
09-004-16 REV. A2018-06-04. Service bulletin. EQUIPMENT; ENGINE AND ENGINE COOLING. Cummins Service Engine Replacement This bulletin involves replacing the engine assembly. Remanufactured long block or short block was installed during a prior repair. A new replacement engine will be installed.
08-047-172018-06-04. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. Flash: RA3/RA4 Radio Software Enhancements This bulletin involves inspecting and if required, updating the radio software. A small number of customers may experience one or more of the following: ? **?Navigation Failed? message is displayed. ? Navigation is inoperative or inaccurate. ? CD player will not play songs and/or locks up the radio. ? The clock will not automatically update to local time. ? The clock may be off by several hours (RA3 only). ? HVAC temperature out of sync with radio display (KL vehicles). ? Some Uconnect App remote commands do not execute with the vehicle. ? Radio Apps are inoperative. ? Radio will lock up. Radio display screen is black or blank. Battery drain due to radio staying on.** Rearview Camera image appears jittery (UF vehicles only). Inability to establish a WiFi connection when security feature is enabled (UF vehicles only). Audio distortion/popping heard while playing Apple devices through the USB port (UF vehicles only). Remote Uconnect Apps functions (i.e. door locks, remote start) inoperative while the engine is running (UF vehicles only). HVAC temperature out of sync with radio display (KL vehicles). Intermittently blind spot chime will not turn off (KL vehicles only). The radio may switch from SiriusXMT to an AM station by itself. Uconnect registration always present, can not remove Uconnect account. Audio muted after AUX device is disconnected. In addition, the following Improvements are included: **Adds Apple SiriT Eyes Free capability for iPhoneT owners. Add the ability to drag and drop icons into the menu bar. Auto Play can now be configured. Enhanced VR performance. Media devices, phone pairing and Bluetooth usage improvements. Improved tuner performance. Enhancements in Connectivity Apps (YelpT, PandoraT, AhaT, etc). Human Machine Interface (HMI) improvements. Adds ?do not disturb? text message feature.**
08-019-17 REV. A2018-06-04. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.; ELECTRICAL SYSTEM:SOFTWARE. RG3 RG4 RJ3 RJ4 Radio Enhancements This bulletin involves inspecting and if required, updating the radio software. A small number of customers may experience one or more of the following:Navigation failed message is displayed (WK and KL with RG3 and RG4). The clock not automatically updating to local time (WK and KL with RG3 and RG4). Poor or no connection to cellular network (WK and KL with RG3 and RG4). HVAC temperature out of sync with radio display (KL with RG3 and RG4). Some Uconnect App remote commands do not execute with the vehicle. Display goes blank/black (WK and KL with RG3 and RG4). Cyrillic keyboard is missing in phone book (WK and KL with RG3 or RG4). Wrong speed limit on NAV speed camera indication (WK and KL with RG3 or RG4). Blind Spot module beep or chime sound may be heard continuously (KL Only). Radio may keep the CAN bus network awake, causing a battery drain. Voice Recognition (VR) to set temperature, will indicate wrong setting to rear seat temperature. Not possible to set temperature in degrees Celsius using the VR (UK vehicles only). Teleprompter does not appear when pressing the VR button. VR operation cancels while in media mode. Radio may display cameras previous image before displaying the current image. Navigation lost vehicle position during route calculation. Navigation displays are missing after vehicle heading changes. Navigation giving incorrect guidance to exit the highway. FM audio may switch to AM after ignition cycle. Text messages appear as senders phone number, not their name. VR phone button may not work at times. Audio muted after AUX device is disconnected. VR Listen to text will only play 1st message. Drive Mode: Eco, Sport or Normal setting may not be saved after key cycle (LA, LD, LX and ZD Only). Drive Mode: Shift light On/Off, out of sync (LA, LD, LX and ZD Only). Speed adjusted volume may not work. AM/FM seek or tuner soft keys may be missing.
90037402018-06-04. Service bulletin. ENGINE AND ENGINE COOLING. Oil Pan 2012-2017 Cummins engines with oil pan leaks, please inspect the shallow area of the oil pan for cracks. If cracks are found, please replace as necessary. Cracks are typically found above the cross member area. Please contact Chad Eichbrecht at cell (248) 309-2695 to arrange for part return or email chad.w.eichbrecht@fcagroup.com If you do not receive a response within 15 minutes, please proceed with normal repair.
90034132018-06-04. Service bulletin. VEHICLE SPEED CONTROL:ACCELERATOR PEDAL. Accelerator Pedal Before replacing accelerator pedal, be sure to follow fault code diagnostic procedures in service manual. Make sure to check wiring and connectors. P2122 and P2127 will set if accelerator pedal connector is disconnected during diagnosis. Make sure codes are active before replacing pedal. DTC P2299 is usually caused by a two footed driver and accelerator pedal should not be replaced for this fault.
25-001-162018-05-21. Service bulletin. FUEL SYSTEM, DIESEL. Diagnosing A Urea Module That Is Exposed To Diesel Fuel This bulletin involves discussing what will happen to the rubber material used in the urea pump when exposed to diesel fuel. This unit is sometimes referred to as the Selective Catalyst Reductant (SCR) module or the Adblue Delivery Module (ADM). Units exposed to hydrocarbons have a particular failure mode, the rubber heater unit is crinkled and in some cases the metal heater protrudes through the rubber membrane. The rubber material used in this unit is designed to withstand Diesel Exhaust Fluid (DEF) only. Exposure to fluids that contain hydrocarbons (i.e. diesel fuel) will damage the unit beyond repair. Units returned that exhibit this failure mode will have warranty claims that are rejected. Units that exhibit this failure mode should be considered customer abuse and should not be covered under warranty. Use the Hydroscopic test paper (P/N 223-44-863) available through MoparEssentialTools.com to confirm exposure.
18-062-162018-05-21. Service bulletin. POWER TRAIN; ENGINE AND ENGINE COOLING. Flash: Powertrain Diagnostic And System Enhancements This bulletin involves reprogramming the Powertrain Control Module (PCM) with the latest available software. A small number of customers may experience a Malfunction Indicator Lamp (MIL) illumination. Upon further investigation the technician may find the following Diagnostic Trouble Codes (DTCs) set in the PCM memory: · **P0335 - Crankshaft Position Sensor Circuit. · P0456 - EVAP System Small Leak. · P2610 - PCM Internal Engine Off Timer Performance.** · P0300 - Multiple Cylinder Misfire. · P0301 - Cylinder 1 Misfire. · P0302 - Cylinder 2 Misfire. · P0303 - Cylinder 3 Misfire. · P0304 - Cylinder 4 Misfire. · P0305 - Cylinder 5 Misfire. · P0306 - Cylinder 6 Misfire. · P0307 - Cylinder 7 Misfire. · P0308 - Cylinder 8 Misfire.
68184926A$2018-05-21. Service bulletin. ELECTRICAL SYSTEM. Integrated Center Stack If vehicle is found within 50 mile radius of the Detroit Metro area please hold vehicle and contact:~ Contact one of the following:~ Daniel Acciacca CELL (586) 709-1537~ Michael Savich CELL (248) 214-7270~ Ayed Hadaad CELL (248) 941-8707~ Issue: On a 2015 & 2016MY LA (Challenger), LD(Charger) and LX (300), the Integrated Center Stack (ICS) may experience a lock-up/Inop condition (complete loss of functionality) during any vehicle diagnostic session (reading fault codes, clearing fault codes, reflashing of any module, etc.). If this occurs, do not replace the ICS. The module functionality can be restored if it is reset by disconnecting power to it (by removing fuse, battery disconnect or module connector disconnect).~

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.