WenmarOpen by Wenmar Pro

Service bulletins for the 2000 Pontiac Bonneville

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

349 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

Bulletins, newest first
PIP5226B2018-02-21. Service bulletin. ENGINE. This Preliminary Information communication provides information to the technician about finding needle bearings during an oil change. Technician will gain access to the roller rockers to inspect them. Only replace the roller rocker that is missing needle bearings. Be sure to clean the oil drains to retrieve the needle bearings. Each roller rocker has 66 bearings.
PIP5540A2018-02-21. Service bulletin. ENGINE. This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components. That any of the listed DTC's may set with or without poor engine performance.
PIP55402018-02-21. Service bulletin. EQUIPMENT. This Preliminary information communicates to the technician the need to inspect the induction system for potential icing issues in very cold ambient temperatures. To allow the ice to melt so that it can be drained from the related components.
PIT54642018-01-22. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that the incoming caller ID may no longer be available or displayed after the Canada OnStar upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIP53252018-01-22. Service bulletin. FUEL SYSTEM, GASOLINE. This Preliminary Information communication provides information to the technician to help determine if the vehicle is equipped with factory or aftermarket Compressed Natural Gas, Liquefied Petroleum Gas, or Bi-Fuel Systems. Technician will check for the Vehicle Emission Control Information Label. By using the engine Regular Production Option Code as well as the Vehicle Emission Control Information Label, technician can confirm the vehicle has a factory installed alternative fuel system or who the manufacturer is of the aftermarket fuel system.
000089027G2017-12-22. Service bulletin. EQUIPMENT. This informational bulletin provides a step by step procedure on how to properly use the GM chemicals to eliminate unwanted odors in vehicles and which products to use for each application.
PIC5588B2017-12-22. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM); EQUIPMENT. This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIC3100F2017-12-14. Service bulletin. ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
PIC5588D2017-10-04. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication provides information to the technician on the programming and activation of the OnStar system. For many 2008 and prior model year GM vehicles, the programming is performed using the Tech 2 and the activation is initiated by a Service Programming System. For the 2010 and UP model year vehicles, the OnStar set-up procedure and OnStar Activation request have been combined into a single programming event called OnStar Set-up and Activation in Service Programming System.
PIT3099P2017-10-04. Service bulletin. EQUIPMENT:OTHER:OWNERS/SERVICE/OTHER MANUAL. This Preliminary Information communication provides information to the technician about installing General Motors Accessory pats. Technician can check Service Information for some accessories. Technician can also contact Partect for assistance. Technician can also contact Techline Customer Support Center for programming issues.
01-08-42-001K2017-08-31. Service bulletin. EXTERIOR LIGHTING:HEADLIGHTS. This informational bulletin provides information on exterior lamp condinsation and replacement guidelines
16-NA-0252017-08-31. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY. This informational bulletin provides information on Behavior of Non-Upgraded OnStar Equipped Vehicles Operating in Canada after Decommissioning of 2G CDMA Cellular Networks
17-NA-0162017-08-31. Service bulletin. WHEELS. This informational bulletin provides information on wheel bearing P/N 13582664 being received new with visible rust and no action is needed as this does not affect the part performance.
17-NA-0162017-08-31. Service bulletin. WHEELS. This informational bulletin provides information on wheel bearing P/N 13582664 being received new with visible rust and no action is needed as this does not affect the part performance.
03-08-46-004S2017-08-31. Service bulletin. ELECTRICAL SYSTEM:SOFTWARE. This informational bulletin provides information on OnStar® VCIM is currently restricted parts. By working closely with our dealers and technicians, through the part restriction process, the General Motors team will gain a better understanding of any field concerns that may develop.
PIP5232B2017-08-15. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. This Preliminary Information communication provides information to the technician about gasoline powered cars, mid-size trucks, light duty trucks, and heavy duty trucks with premature catalytic converter failures. It is recommended to inspect for a poor crimp on the grounds ring terminal at the engine block for the bank with the concern and repair the wire.
PIC3100E2017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). This Preliminary Information communication provides information to the technician about vehicle's odometer appears to be inaccurate relative to a known distance traveled. Technician should obtain a hand-held GPS unit to test the odometer. If a hand held GPS unit is not available, the only other option is to verify the miles traveled using a surveyor's wheel or a dynamometer.
PIC6140A2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that has a red LED and DTC B2455 setting current in the Vehicle Communication Interface Module after performing Canada upgrade. Technician will need to gain access to the Vehicle Communication Interface Module. After gaining access to the Vehicle Communication Interface Module pull the tape back on the X2 connector then tape the bare wires individually to prevent them from shorting.
PIP53462017-08-15. Service bulletin. EQUIPMENT; POWER TRAIN:AUTOMATIC TRANSMISSION:COOLING UNIT AND LINES; POWER TRAIN. This Preliminary Information communication provides information to the technician about cooler line fittings that come with the 4T65E General Motors remanufactured transmission may not be the same as Original equipment manufacturer quick connect verses inverted flare. Dealer will need to contact General Motors Technical Assistance Center for further assistance.
PIC61072017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about being unable to receive OnStar ?Over The Air? updates. Technician will need to press the OnStar button and verify they have an active account and that the call connects with data and location.
PIT5384A2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that may have the OnStar wireless fidelity inoperative. Technician will need to contact General Motors Technical Assistance Center with a scan tool connect to the vehicle for further assistance.
PIC6140B2017-08-15. Service bulletin. ELECTRICAL SYSTEM. This Preliminary Information communication provides information to the technician about vehicles that has a red LED and DTC B2455 setting current in the Vehicle Communication Interface Module after performing Canada upgrade. Technician will need to gain access to the Vehicle Communication Interface Module. After gaining access to the Vehicle Communication Interface Module pull the tape back on the X2 connector then tape the bare wires individually to prevent them from shorting.
PIT54862017-08-15. Service bulletin. EQUIPMENT:ELECTRICAL:RADIO/TAPE DECK/CD ETC.. This Preliminary Information communication provides information to the technician about vehicles that when dialing certain numbers using OnStar Hands-free Calling, the audio is distorted or has poor quality after performing the OnStar Canada Upgrade. Dealer should communicate to the customer that we apologize for this inconvenience and that General Motors is working on a solution for this concern.
PIT54842017-08-15. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT:ELECTRICAL; EQUIPMENT; ELECTRICAL SYSTEM:SOFTWARE. This Preliminary Information communication advises the technician that if OnStar is unable to configure the vehicle after the OnStar 15-08-44-001 upgrade and Onstar receives a 118 error code when attempting to configure the vehicle. Dealers should receive a sheet with the kit that provides steps to assist with handling this error. Dealer will follow one of the listed steps to resolve the issue. If there are still configuration issues, please contact the OnStar Technical Assistance Centre for assistance.
PIT4943D2017-08-15. Service bulletin. FUEL SYSTEM, GASOLINE; FUEL SYSTEM, OTHER:STORAGE:TANK ASSEMBLY; ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. This Preliminary Information communication provides information to the technician about vehicles that have a Service Engine Soon Malfunction Indicator Lamp. Technician may find Diagnostic Trouble Code P0442. Technician will need to review Techlink article from May 2013 titled "Using the Evaporative Emissions System Tester" Technician will need to follow these steps to help diagnose the issue. First after the P0442 has been verified do not disturb any of the fuel system components. The technician now can use the scan tool to close the Evaporative Emissions System. If possible change the tank pressure sensor units from inch_H2O to milimeter_Hg for better resolution. Now the vehicle can be stared to monitor the tank pressure sensor output value for approximately two minutes. If the tank pressure sensor value does change, pressurize the fuel tank side of the purge solenoid with the GE 41413-A / J 41413-A and the necessary adaptors. Now add smoke and allow pressure to stabilize for 2 minutes. If smoke is allowed to pass through the purge solenoid, replace the purge solenoid. If the tank pressure sensor value does not change, then install CH-48096 adaptor between the purge line from the canister and the purge solenoid. With the Evaporative Emissions System closed, pressurize the system through the CH-48096 adaptor and allow the system to completely stabilize, by observing the Press / Vac Gauge for a minimum of 5 minutes. Now add smoke to the system with GE 41413-A / J 41413-A after system stabilization. Now inspect the purge solenoid, engine side, fuel cap, canister vent solenoid filter and any line quick connects. When the leak is unable to be located, test under a vacuum condition. his type of leak may be detected by using the scan tool Purge/Seal function to create a vacuum in the Evaporative Emissions System and then observe the FTP sensor parameter for vacuum decay.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.