WenmarOpen by Wenmar Pro

Service bulletins for the 2014 Nissan Rogue

A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.

332 on file from NHTSA, as of 2026-10-19.

By type

By component

By trouble code

By topic

Only bulletins with component: Electrical system are shown. Show all

Bulletins, newest first
NTB140672021-05-10. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; ELECTRICAL SYSTEM; EQUIPMENT. IF YOU CONFIRM The maintenance interval mileage in the Vehicle Information Display resets to zero with each ON > OFF > ON ignition cycle, ACTION Reprogram the Vehicle Information Display (METER/M&A) per the Service Procedure in this bulletin. See this bulletin for further detail.
NTB14039A2021-05-10. Service bulletin. ELECTRICAL SYSTEM:BODY CONTROL MODULE/BCM; ENGINE AND ENGINE COOLING:ENGINE:ENGINE CONTROL MODULE (ECU/ECM):SOFTWARE. SERVICE INFORMATION If one or both Intelligent Keys cannot be located prior to customer delivery of an Applied Vehicle, refer to the applicable section of this bulletin for Intelligent Key registration instructions. - One (1) Intelligent Key Is Lost ---- Page 2 - Two (2) Intelligent Keys Are Lost ---- Page 3 NOTE - If both Intelligent Keys are lost with the BCM in Transit Mode, the BCM and ECM will need to be replaced. Refer to pages 3 - 5 for more information. See this bulletin for more detail.
NTB10066A2021-05-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information.
PC300A2021-05-10. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM:IGNITION. The original VIN list provided with the initial announcement contained 29 vehicles that are not equipped with push-button ignition. These 29 vehicles are exempt from the repair and are no longer subject to the quality hold.
PC3002021-05-10. Service bulletin. ELECTRICAL SYSTEM; ELECTRICAL SYSTEM:IGNITION. Nissan is conducting a dealer inventory service action to replace the push button ignition switch on 158 specific 2014 Rogue vehicles identified in SERVICE COMM.
NTB140472021-05-10. Service bulletin. ELECTRICAL SYSTEM; STRUCTURE. IF YOU CONFIRM: The "front door power window and door lock/unlock switch (RH) finisher" (switch finisher) has a loose fit, causting an excessive gap. See Figure 1. ACTION: 1. Remove the passenger front door finisher (door finisher). - Refer to the Electronic Service Manual (ESM), section INT-Interior, for removal procedure. 2. Install a foam block where shown in SERVICE PROCEDURE. - Use the foam block listed in PARTS INFORMATION. 3. Install the door finisher with a new switch finisher listed in PARTS INFORMATION. - Refer to the ESM, section INT-Interior, for installation procedure. See this bulletin for further detail.
NTB140382021-05-10. Service bulletin. EQUIPMENT ADAPTIVE/MOBILITY; EQUIPMENT; ELECTRICAL SYSTEM. SERVICE INFORMATION When registering the Intelligent Keys (I-Keys) to a vehicle for one of the following concerns: * After replacing the BCM. Or * When one of the I-Keys has been lost and needs to be replaced. Or * When additional I-Keys are being added to the vehicle. Always use the following steps to insure proper registration of the I-Keys: 1. First Initialize the BCM. 2. Register all of the vehicle?s ?previously registered? I-Keys to the vehicle first. And then 3. Register any new (additional) I-Keys only after all of the pre-existing I-Keys have been registered. 4. Confirm operations of all I-Keys. Please see this bulletiln for further details.
NTB140322021-05-10. Service bulletin. ELECTRICAL SYSTEM:WIRING. SERVICE INFORMATION Warranty claims coding for repairing wiring harnesses for all Nissan vehicles has changed. This bulletin gives an outline of the technician?s responsibilities in assisting the dealer?s claims administrator to properly code a harness repair. Failure to provide correct information may result in claims suspension or rejection. See this bulletin for further detail.
NTB140262021-05-10. Service bulletin. ELECTRICAL SYSTEM. IF YOU CONFIRM: An electrical issue caused by corrosion in the Main Harness to Body Harness connectors located at the bottom of the driver side A-pillar: Connector numbers M13 to B3 and/or M14 to B4. ACTIONS: 1. Preform repairs to harness connectors as needed. 2. Apply Harness Protector to cover the harness connectors. See this bulletin for further detail.
NTB140212021-05-10. Service bulletin. STEERING; ELECTRICAL SYSTEM: INSTRUMENT CLUSTER/PANEL. IF YOU CONFIRM The Instrument Lower Panel LH (as shown in Figure 1) molded plastic clip will not stay secured. ACTION Install a shim between the Steering Member and the Instrument Panel and apply felt tape to the Instrument Lower Panel LH with the SERVICE PROCEDURE starting on page 2. Please see this bulletin for further details.
PC2602021-05-10. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. Nissan is conducting a Dealer Service Action to inspect the CVT output speed sensor on certain specific 2014 Nissan Altima, Pathfinder, Rogue vehicles currently in dealer inventory only.
NTB131072021-05-10. Service bulletin. ENGINE AND ENGINE COOLING; ELECTRICAL SYSTEM. SERVICE INFORMATION Intelligent Key (I-Key) systems on the Applied Vehicles use two (2) different Radio Frequencies (RF) that are similar to other wireless devices; 315 MHz and 433 MHz. In the event another wireless device (e.g. aftermarket alarm system) is transmitting at the same time as an I-Key, it can interfere with the I-Key signals being received by the BCM. If there is interference with I-Key signals, the following symptoms may occur: - The I-key is not detected, causing: - The engine to not start (no response when the Stop/Start button is pressed) - "I-Key System Error" displayed in the instrument cluster - "No I-Key Detected" displayed in the instrument cluster - Intermittent operation of the buttons on the remote (Key FOB). - Intermittent operation of the door request switches. If a vehicle has experienced the above symptoms, or a customer has reported the above symptoms, refer to Supplemental Diagnosis / Information in this bulletin. See this bulletin for further detail.
NTB16-047A2021-05-09. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. 2014-2016 ROGUE; INTELLIGENT KEY AND/OR ELECTRICAL ISSUES AFTER INSTALLATION OF AFTERMARKET REMOTE START This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB14-114B2021-05-09. Service bulletin. EQUIPMENT; ELECTRICAL SYSTEM. INTELLIGENT KEY DOES NOT WORK INTERMITTENTLY This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB17-014A2021-04-09. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. BLUETOOTH, USB, AND AUX FUNCTION DIAGNOSTIC TOOL This bulletin has been amended. See AMENDMENT HISTORY on page 3. Please discard previous versions of this bulletin.
NTB15-011C2021-04-09. Service bulletin. ELECTRICAL SYSTEM. NISSAN CONNECT NAVIGATION SYSTEM SOFTWARE UPDATE This bulletin has been amended. See AMENDMENT HISTORY on page 9. Please discard previous versions of this bulletin.
NTB13-106G2021-04-08. Service bulletin. LANE DEPARTURE:LANE KEEP:NAVIGATION SYSTEM/SOFTWARE; ELECTRICAL SYSTEM; BACK OVER PREVENTION: SENSING SYSTEM: CAMERA. CORRECT OPERATION OF AUDIO CONTROLS AND BACK-UP CAMERA REQUIRES CONFIGURATION WITH C-III PLUS This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB13-099G2021-04-08. Service bulletin. EQUIPMENT:ELECTRICAL:AUX AUDIO JACK/PLUG; ELECTRICAL SYSTEM; EQUIPMENT:ELECTRICAL:NAVIGATIONAL SYSTEM(GLOBAL POSITIONING SYSTEM). AUDIO UNIT REPLACEMENT - VEHICLES WITH COLOR DISPLAY AUDIO AND NAVIGATION SYSTEM This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin
NTB13-096C2021-04-08. Service bulletin. ELECTRICAL SYSTEM. AUDIO UNIT REPLACEMENT - NON-NAVIGATION VEHICLES WITH COLOR DISPLAY AUDIO This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB13-085C2021-04-08. Service bulletin. ELECTRICAL SYSTEM. 2014-2015 ALTIMA & 2014 ROGUE; AUDIO VISUAL SYSTEM SOFTWARE UPDATE This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin.
NTB12-099E2021-04-08. Service bulletin. ELECTRICAL SYSTEM. NAVIGATION WILL NOT WORK AFTER SD MAP CARD INSTALLED This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB12-110d2021-02-06. Service bulletin. ELECTRICAL SYSTEM. POWER BACK DOOR CALIBRATION This bulletin has been amended. See AMENDMENT HISTORY on the last page. Discard all previous versions of this bulletin.
NTB20-0692020-10-08. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. ROGUE AND ROGUE SPORT; VIBRATION AND/OR NOISE WHEN MAKING LOW SPEED TURNS IF YOU CONFIRM There is a vibration or judder feeling from the rear of the vehicle during the following conditions: • When making turns • On dry roads • At low speeds (under 40 MPH) And • The above vibration does not occur if the electric controlled coupling is electrically disconnected. ACTION 1. Confirm the AWD control unit part number, and replace it, if applicable. 2. Replace the electric controlled coupling for the rear final drive. 3. Perform Unit Characteristics Writing.
NTB19-0802019-11-08. Service bulletin. UNKNOWN OR OTHER; ELECTRICAL SYSTEM. 2014-2020 ROGUE; NO AIR FLOW FROM VENTS DUE TO SNOW BUILD-UP IF YOU CONFIRM Or the customer states there is no air flow from any of the HVAC vents And There is snow build-up in and around the blower motor air inlet, behind the cowl. ACTION 1. Remove all snow, water, and debris from the blower motor inlet, cowl area, and where the blower motor mounts. 2. Clean or replace the blower motor as needed. 3. If the blower motor does not work on all speed settings, replace the variable blower control (fan resistor). 4. If not already equipped: Install the cowl and wiper pivot filters listed in PARTS INFORMATION on the last page of this bulletin.
NTB19-0712019-10-09. Service bulletin. ELECTRICAL SYSTEM; AIR BAGS. DTC B00A0-00 STORED IF YOU CONFIRM DTC B00A0-00 (OCCUPANT DETECTION SENSOR UNIT) is stored And OCS zero point reset cannot be performed (continued on the next page) And The following screen displays: ACTION 1. Check the Occupant Classification System (OCS) control unit using the ODS Analysis tool software. • Refer to SERVICE PROCEDURE on page 5. HINT: “OCS” may also be referred to as “ODS”. 2. Perform “75-zero RESET”.

The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.