Service bulletins for the 2006 Nissan Frontier
A bulletin is a manufacturer's communication to its dealers, as NHTSA indexes it. The summary is NHTSA's. The document is the manufacturer's: read it at NHTSA. A bulletin is not a recall, and listing a model year does not mean every vehicle of it is concerned.
99 on file from NHTSA, as of 2026-10-19.
By type
By component
By trouble code
| NTB09099A | 2021-05-10. Service bulletin. EQUIPMENT:APPLIANCE:AIR CONDITIONER; EQUIPMENT ADAPTIVE/MOBILITY. IF YOU CONFIRM A refrigerant leak at a refrigerant pipe/hose joint location. ACTIONS 1. Inspect the metal surfaces of the pipe/hose joint for damage or contamination. NOTE: Do not replace a refrigerant pipe, hose, or other A/C component if an o-ring seal will solve the leak incident, if it should occur. 2. If no damage is found to the joint metal surfaces, replace the O-ring seal. See this bulletin for further detail. |
|---|---|
| NTB09131B | 2021-05-10. Service bulletin. FORWARD COLLISION AVOIDANCE; EQUIPMENT:OTHER:LABELS. SERVICE INFORMATION Because of collision damage or other vehicle repair, a replacement "Certification Label" or "VIN Plate / Label" may be needed. These items may be available from Nissan by request if certain criteria are met. This bulletin lists the criteria and provides an application form for such replacements. See this bulletin for further detail. |
| NTB15079A | 2021-05-10. Service bulletin. FUEL SYSTEM, GASOLINE. IF YOU CONFIRM: The MIL is ON with DTC P0448 (EVAP canister vent control valve close) stored in the ECM. ACTION: 1. Replace the EVAP canister (canister) and EVAP canister vent control valve (vent control valve). 2. Remove the canister filter. 3. Attach the EPT foam seal to fuel filler tube. 4. Replace the fuel filler pipe, canister drain hose, and fuel filler cap (on some model years) listed in PARTS INFORMATION. 5. Erase the DTC. See this bulletin for further detail. |
| NTB09081C | 2021-05-10. Service bulletin. VISIBILITY. SERVICE INFORMATION The purpose of this bulletin is to give Nissan dealers guidelines to help determine if windshield breakage is covered under warranty or is the customer?s responsibility. Nissan North America (NNA) is not responsible for damage to glass that is a result of objects striking or scratching the glass. However, NNA is responsible for manufacturing issues such as distorted glass and cracks that are due to improper installation or damage to the glass during vehicle assembly. NNA typically does not find any type of cracks in the windshield due to stress after the dealership PDI. See this bulletin for further detail. |
| NTB15107 | 2021-05-10. Service bulletin. POWER TRAIN. IF YOU CONFIRM: A remanufactured automatic transmission supplied by ATC Drivetrain is installed in an APPLIED VEHICLE AND CONSULT-III plus (C-III plus) is not able to communicate with the TCM through Diagnosis (One System) OR C-III plus is able to communicate with the TCM, but the TCM part number?s (P/N) sixth digit is a "5", "6", or "7" (for example, 31020-7xxxx). NOTE: To determine if an applied vehicle is equipped with an ATC Drivetrain remanufactured A/T, see page 3. ACTION: Refer to the Flow Chart on page 2. See this bulletin for further detail. |
| NTB14068A | 2021-05-10. Service bulletin. VISIBILITY. SERVICE INFORMATION Power moonroof initialization procedures for the Applied Vehicles have been revised. The procedure described in this bulletin differs from the procedure in the Electronic Service Manual (ESM). At a later date and where possible, the applicable ESMs will be updated with the revised procedures. Follow the procedure in this bulletin should the power moonroof in an Applied Vehicle need to be initialized. See this bulletin for further details. |
| NTB13028A | 2021-05-10. Service bulletin. VISIBILITY. SERVICE INFORMATION Windshield "foreign material" that is on the surface of the glass in some cases can be cleaned off with a very particular type and grade of steel wool. * Most any foreign material on the surface of the Windshield can be cleaned off by using #0000 super fine steel wool. >The #0000 grade super fine steel wool can be found in most hardware stores. Please see this bulletin for further details. |
| NTB13088A | 2021-05-10. Service bulletin. BACK OVER PREVENTION; WHEELS; SERVICE BRAKES; LANE DEPARTURE. SERVICE INFORMATION This bulletin has compiled Tire Pressure Monitor System (TPMS) and Low Tire Pressure Warning System (LTPWS) information for: - Basic diagnosing of TPMS/LTPWS systems - Radio frequency interference causing a "No Data" (C1708, C1709, C1710, C1711) condition - Sensor leaks - Moving TPMS/LTPWS wheel assemblies from one vehicle to another and TPMS/LTPWS sensor registration - Air pressure changes with altitude and ambient temperatures - Aftermarket tire sealers - Aftermarket wheels - Inflating/deflating tires with TPMS/LTPWS sensors See this bulletin for further detail. |
| NTB15055 | 2021-05-10. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL. SERVICE INFORMATION After ECM reprogramming, the Calibration Verification Number (CVN) needs to be automatically calculated prior to State emissions testing (also known as Inspection Maintainence, I/M, or SMOG testing depending upon location). Allowing the vehicle to idle for 22 minutes will allow for faster CVN calculation. It is recommended that customers utilize this method if the vehicle needs to be tested for emissions soon after ECM reprogramming. See this bulletin for further detail. |
| NTB12078A | 2021-05-10. Service bulletin. POWER TRAIN; STEERING. SERVICE INFORMATION When diagnosing possible power steering gear (rack and pinion steering rack, or steering rack) leak issues, it may appear the steering rack is leaking when actually, it?s not. Use this service bulletin to help make a more accurate diagnosis of the steering rack. See this bulletin for further detail. |
| NTB00042D | 2021-05-10. Service bulletin. AIR BAGS; BACK OVER PREVENTION; EQUIPMENT. SERVICE INFORMATION Changes or modifications to the front seat assembly trim materials may affect the proper operation of the Front Seat-Mounted Side-Impact Supplemental Air Bags and Passenger Occupant Classification Sensor and could result in serious personal injury or death. Nissan STRONGLY RECOMMENDS AGAINST making any change to seat trim materials from the factory equipped condition. This specifically applies to replacing the seat trim with non-factory materials; adding leather/cloth seat covers, seat pads, or seat storage pouches, etc. around or over the seat back and the passenger seat cushion. See this bulletin for further detail. |
| NTB11021A | 2021-05-10. Service bulletin. BACK OVER PREVENTION; AIR BAGS. IF YOU CONFIRM: Squeal/Squeak noise from the front brakes: While moving forward or reverse, with very light brake application (pedal pressure), after the vehicle has been sitting, typically overnight ("cold" brakes), at speeds less than 10 MPH, while traveling straight or turning. ACTION: Replace the hardware on both front brake calipers with the kit listed in the Parts Information in this bulletin. See this bulletin for further detail. |
| NTB14107 | 2021-05-10. Service bulletin. POWER TRAIN; ELECTRICAL SYSTEM. SERVICE INFORMATION If a customer describes lack of power or poor acceleration, perform the following checks before attempting any repair: * Check for stored DTCs. * Check if the driver is resting their left foot on the brake pedal while accelerating. Advise the customer not to rest their foot on the brake while accelerating. * Use CONSULT-III plus in Engine Data Monitor to check operation of the brake lamp circuit signal. Monitor the brake switch during the incident; it should be "OFF". Please see this bulletn for further details. |
| NTB10066A | 2021-05-10. Service bulletin. ELECTRICAL SYSTEM; EQUIPMENT. SERVICE INFORMATION Related to communication codes U1000, U1001, U1002, U1010: - Always diagnose the communication codes first. - When a module reports a U1000 code, it is typically operating normally; however, there is a communication error external to that module on the CAN network. - U1000 indicates an error. V-CAN diagram or CAN Diag Support Monitor provides data to determine the location of the error. See this bulletin for more information. |
| NTB13081A | 2021-05-10. Service bulletin. EQUIPMENT; EQUIPMENT ADAPTIVE/MOBILITY. SERVICE INFORMATION The specifications for the intake and exhaust valves and valve lifter service parts have been changed. * The valve stem length of both intake and exhaust valve has been increased (Figure 1) and are a direct replacement for the shorter style valve. * The related valve lifter cup has been shortened (Figure 2) and the point at which the valve lifter contacts the valve stem has been shortened (not shown). These service parts will require that the valve and valve lifter be replaced at the same time. See this bulletin for further details. |
| NTB08055C | 2021-05-10. Service bulletin. EQUIPMENT; AIR BAGS. SERVICE INFORMATION Information necessary to service the Supplemental Restraint System (SRS) safely is included in the "RESTRAINTS" section of the Electronic Service Manual (ESM) for each vehicle. IMPORTANT: Turn the ignition switch OFF, disconnect both battery terminals, and wait at least 3 minutes before performing any service on the SRS. See this bulletin for further detail. |
| NTB92123D | 2021-05-10. Service bulletin. WHEELS; EQUIPMENT. Nissan Original Equipment or Genuine Accessory Alloy wheels, along with their finish coating (clear, chrome, titanium, etc.), are specifically developed to achieve Nissan design and performance standards. These Original Equipment or Genuine Accessory wheels are subjected to testing to ensure they meet Nissan's standards. Nissan Original Equipment Alloy or Genuine Accessory wheels subjected to aftermarket chroming may no longer continue to meet these standards and may be seriously damaged. Therefore, Nissan most strongly discourages, and recommends that these wheels NEVER be subjected to, aftermarket chroming. See this bulletinfor further detail. |
| NTB13027A | 2021-05-10. Service bulletin. ELECTRICAL SYSTEM. SERVICE INFORMATION This TSB is for troubleshooting of CAN Modules with "Diag-On-CAN" Diagnostics. The flow charts below are meant to troubleshoot current CAN DTCs. The flow charts are intended to diagnose one module at a time; repeat the process as needed for additional control units. Please see this bulleitn for further details. |
| NTB04094A | 2021-05-10. Service bulletin. STEERING; SERVICE BRAKES; WHEELS. If YOU CONFIRM: A vehicle needs to have the brake rotors resurfaced (front or rear). ACTION: Use the ProCut PFM Series on-car brake lathe to perform brake rotor resurfacing and follow the tips listed in this bulletin. - The ProCut PFM Series brake lathe has been chosen as the approved tool for rotor resurfacing. - The ProCut PFM Series brake lathe can be ordered from TECH-MATE at 1-800-662-2001. - ProCut technical support or service can be obtained by calling 1-800-543-6618. NOTE: Brake rotors may need to be resurfaced during routine brake repair or for brake "judder" incidents. - Brake judder: A brake pedal pulsation and/or steering wheel shimmy when braking that occurs when there is too much thickness variation of the brake rotors (see NTB00-033). See this bulletin for further detail. |
| NTB00033E | 2021-05-10. Service bulletin. SERVICE BRAKES; WHEELS; SUSPENSION; STEERING. SERVICE INFORMATION - This bulletin is to assist you in responding to customer questions about brake operation, and provides diagnostic and repair information for each item listed, if any should occur. - Most brake incidents fall into the following categories: a. Brake Noise: A squeak, squeal, clunk, or groan that occurs when the brakes are applied or released. b. Brake Judder: A vibration that can be felt in the vehicle, steering wheel or brake pedal when the brakes are applied. c. Pedal Feel: The effort needed to operate the brakes is too high or too low. SERVICE PROCEDURE 1. Verify the condition by road testing the vehicle with the customer. 2. Determine the specific brake incident based on the description in the Service Information above. 3. Follow the appropriate repair procedure(s), listed on the following pages, for your specific incident. See this bulletin for further details. |
| NTB98018G | 2021-05-10. Service bulletin. ELECTRICAL SYSTEM. As part of an enhanced emissions test for Inspection & Maintenance (I/M), some States may require the System Readiness Test (SRT) status be checked. - The SRT is used to indicate whether the engine control module (ECM) has completed self diagnosis of major emissions systems and components. - In these instances the State may require completion of the SRT before permitting the emissions inspection to proceed. Refer to this Bulletin for further details. |
| NTB99001A | 2021-05-10. Service bulletin. SUSPENSION. SERVICE INFORMATION This bulletin provides information to identify: - A leaking strut or a shock absorber that qualifies for replacement under warranty. - A strut or shock absorber that has slight oil seepage, a condition which is considered normal, does not affect strut/shock absorber operation or performance, and does not require replacement. - A strut or shock absorber that should be replaced due to rod resistance/noise issues. See this bulletin for further detail. |
| MAILM | 2021-05-10. Service bulletin. POWER TRAIN:AUTOMATIC TRANSMISSION. Nissan has decided in the interest of customer satisfaction, to further extend the warranty for the Radiator Assembly on all 2005-10 Frontier, Pathfinder, and Xterra vehicles equipped with automatic transmissions. |
| NTB99-001e | 2021-03-06. Service bulletin. SUSPENSION. STRUT AND SHOCK ABSORBER REPLACEMENT GUIDELINES This bulletin has been amended. See AMENDMENT HISTORY on the last page. Please discard previous versions of this bulletin. |
| DOR-M9J4S-07 | 2020-07-27. Service bulletin. ENGINE AND ENGINE COOLING:EXHAUST SYSTEM:EMISSION CONTROL:CATALYTIC CONVERTOR. These SKUs are Exhaust Manifolds with Catalytic Converters. The customer communication requested return of unsold inventory due to a loss of CARB certification. These SKUs can no longer be sold as they do not meet CARB standards, but parts on vehicles are not effected. |
The summaries are NHTSA's. Each bulletin's page links NHTSA's copy of the manufacturer's document.